Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM
RM27L0U _51 Engine / Hybrid System _049293 3UR-FBE ENGINE CONTROL _0235531 SFI SYSTEM C

3UR-FBE ENGINE CONTROL  SFI SYSTEM  P0451  Evaporative Emission Control System Pressure Sensor Range / Performance  P0452  Evaporative Emission Control System Pressure Sensor / Switch Low Input  P0453  Evaporative Emission Control System Pressure Sensor / Switch High Input  


DTC SUMMARY

DTC Monitoring Item Malfunction Detection Condition Trouble Area Detection Timing Detection Logic
P0451 Canister pressure sensor abnormal voltage fluctuation Sensor output voltage fluctuates frequently within a certain time period.
·

Canister pump module

·

Connector/wire harness

(Canister pump module - ECM)

·

EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose)

·

ECM


·

EVAP monitoring (ignition switch off)

·

Engine running


2 trip
Canister pressure sensor constant voltage Sensor output voltage does not vary in a certain time period.
·

EVAP monitoring (ignition switch off)


P0452 Canister pressure sensor low input EVAP pressure less than 42.11009 kPa-a for 0.5 seconds.
·

Canister pump module

·

Connector/wire harness

(Canister pump module - ECM)

·

EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose)

·

ECM


·

Ignition switch ON

·

EVAP monitoring (ignition switch off)


1 trip
P0453 Canister pressure sensor high input EVAP pressure more than 123.76147 kPa-a for 0.5 seconds.
·

Canister pump module

·

Connector/wire harness

(Canister pump module - ECM)

·

EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose)

·

ECM


·

Ignition switch ON

·

EVAP monitoring (ignition switch off)


1 trip

HINT:

The canister pressure sensor is built into the canister pump module.


DESCRIPTION

The description can be found in the EVAP (Evaporative Emission) System (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>EVAP System).

MONITOR DESCRIPTION

A311003E07
5.042,1.115 4.667,1.563 false 5.052,2.927 4.667,3.448 false 0.156,0.135 3.24,0.333 3.083,0.198 10 false Canister Pressure Sensor Specification (fig. 2): 1.813,1.594 2.375,1.792 0.563,0.198 10 false 4.900 V 1.813,2.083 2.375,2.281 0.563,0.198 10 false 4.423 V 1.813,2.781 2.375,2.979 0.563,0.198 10 false 1.425 V 1.813,3.26 2.375,3.458 0.563,0.198 10 false 0.450 V 1.375,1.052 2.375,1.25 1,0.198 10 false Output Voltage 5.031,3.427 5.677,3.625 0.646,0.198 10 false Pressure 5.094,1.021 6.188,1.219 1.094,0.198 10 false Malfunction Area 5.094,2.865 6.188,3.063 1.094,0.198 10 false Malfunction Area 3.031,3.656 3.313,3.833 0.281,0.177 10 false 60 3.719,3.646 4.052,3.854 0.333,0.208 10 false 115 4.406,3.646 4.906,3.823 0.5,0.177 10 false kPa-a 4.146,2.323 5.094,2.521 0.948,0.198 10 false Usable Range 1.219,4.313 5.115,4.51 3.896,0.198 10 false Standard atmospheric pressure is 101.3 kPa-a (760 mmHg-a) 1.219,4.094 1.646,4.292 0.427,0.198 10 false HINT: 2.979,3.813 3.396,4.01 0.417,0.198 10 false (450) 3.698,3.792 4.094,4 0.396,0.208 10 false (862) 4.375,3.792 5.073,4 0.698,0.208 10 false (mmHg-a)

1.

DTC P0451: Canister pressure sensor abnormal voltage fluctuation or being constant

If the canister pressure sensor voltage output fluctuates rapidly for 10 seconds, the ECM stops the EVAP system monitor. The ECM interprets this as the canister pressure sensor voltage fluctuating, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC. Alternatively, if the sensor voltage output does not change for 10 seconds, the ECM interprets this as the sensor being stuck, and stops the monitor. The ECM then illuminates the MIL and stores the DTC. (Both the malfunctions are detected by 2 trip detection logic.)

2.

DTC P0452: Canister pressure sensor voltage low

If the canister pressure sensor output [pressure] is below 42.11009 kPa-a (315.86779 mmHg-a), the ECM interprets this as an open or short circuit malfunction in the canister pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC (1 trip detection logic).

3.

DTC P0453: Canister pressure sensor voltage high

If the canister pressure sensor output [pressure] is 123.76147 kPa-a (928.33489 mmHg-a) or more, the ECM interprets this as an open or short circuit malfunction in the canister pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC (1 trip detection logic).


MONITOR STRATEGY

Required Sensors/Components Canister pump module
Frequency of Operation Continuous
Duration 0.5 seconds: P0452 and P0453
Within 2 minutes: P0451 (sensor stuck)
Less than 15 seconds: P0451 (sensor noise)
MIL Operation Immediate: P0452 and P0453
2 driving cycles: P0451
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

P0451 (Noise monitor):
Monitor runs whenever following DTCs not stored None
Atmospheric pressure (absolute pressure) 70 to 110 kPa-a (525 to 825 mmHg-a)
Battery voltage 10.5 V or more
Intake air temperature 4.4 to 40°C (40 to 104°F)
Either of following conditions met A or B
A. Engine condition Running
B. Time after key off 5 or 7 or 9.5 hours
Canister pressure sensor malfunction (P0452, P0453) Not detected

P0451 (Stuck monitor):
Battery voltage 10.5 V or more
Intake air temperature 4.4 to 40°C (40 to 104°F)
Canister pressure sensor malfunction (P0452, P0453) Not detected
Atmospheric pressure 70 to 110 kPa-a (525 to 825 mmHg-a) [absolute pressure]
Time after key off 5 or 7 or 9.5 hours

P0452 and P0453:
Monitor runs whenever following DTCs not stored None
Battery voltage 8 V or higher
Starter OFF
Either of following conditions met (a) or (b)
(a) Ignition switch ON
(b) ECM Wake up by soak timer

TYPICAL MALFUNCTION THRESHOLDS

P0451: Canister pressure sensor noise
Frequency that EVAP pressure change 0.3 kPa-g (2.25 mmHg-g) or more 10 times or more in 10 seconds

P0451: Canister pressure sensor stuck
EVAP pressure change during reference pressure measurement Less than 0.65 kPa (4.876 mmHg)

P0452: Canister pressure sensor range check (low voltage)
EVAP pressure Less than 42.11009 kPa-a (315.86779 mmHg-a)

P0453: Canister pressure sensor range check (high voltage)
EVAP pressure More than 123.76147 kPa-a (928.33489 mmHg-a)

CONFIRMATION DRIVING PATTERN

NOTICE:
·

The Evaporative System Check (Automatic Mode) consists of 6 steps performed automatically by the Techstream. It takes a maximum of approximately 24 minutes.

·

Do not perform the Evaporative System Check when the fuel tank is more than 90% full because the cut-off valve may be closed, making the fuel tank leak check unavailable.

·

Do not run the engine during this operation.

·

When the temperature of the fuel is 35°C (95°F) or higher, a large amount of vapor forms and any check results become inaccurate. When performing the Evaporative System Check, keep the fuel temperature below 35°C (95°F).



1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the Techstream on.

7.

Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.

8.

After the Evaporative System Check is completed, check All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

9.

Input the DTC: P0451, P0452 or P0453.

10.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:

If the judgment result shows ABNORMAL, the system has a malfunction.


11.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A244835E02
5.884,7.066 6.221,7.222 0.336,0.156 10 ECM 5.443,0.596 5.891,0.752 0.448,0.156 10 MPMP 5.1,0.606 5.381,0.775 0.281,0.170 10 A27 5.1,3.282 5.381,3.451 0.281,0.170 10 A27 5.1,6.106 5.381,6.276 0.281,0.170 10 A27 5.156,0.442 5.340,0.598 0.184,0.156 10 49 5.436,1.591 5.856,1.750 0.420,0.159 10 VCV1 5.1,1.689 5.388,1.852 0.288,0.163 10 D56 5.149,1.514 5.346,1.684 0.198,0.170 10 67 5.436,2.067 5.870,2.223 0.434,0.156 10 PPMP 5.106,1.969 5.366,2.132 0.260,0.163 10 121 5.1,2.151 5.395,2.307 0.295,0.156 10 D56 5.1,2.608 5.395,2.764 0.295,0.156 10 D56 5.1,4.196 5.395,4.352 0.295,0.156 10 D56 5.436,2.53 5.870,2.686 0.434,0.156 10 ETHW 5.151,2.437 5.336,2.592 0.185,0.156 10 97 5.436,3.286 5.873,3.446 0.437,0.159 10 VPMP 5.15,3.118 5.347,3.274 0.198,0.156 10 30 5.442,4.203 5.803,4.362 0.361,0.159 10 PRG 5.148,4.035 5.359,4.191 0.211,0.156 10 63 5.436,6.013 5.870,6.169 0.434,0.156 10 MREL 5.152,5.932 5.343,6.081 0.191,0.149 10 34 1.457,0.504 1.919,0.660 0.461,0.156 10 MGND 1.279,0.52 1.393,0.690 0.114,0.170 10 4 2.9,0.504 3.334,0.660 0.434,0.156 10 MTRB 3.37,0.516 3.484,0.672 0.114,0.156 10 3 1.642,3.691 2.041,3.847 0.399,0.156 10 O24 1.642,3.843 3.090,4.027 1.448,0.184 10 Canister Pump Module 1.707,0.792 3.085,0.976 1.378,0.184 10 Leak Detection Pump 1.45,2.845 3.078,3.015 1.628,0.170 10 Canister Pressure Sensor 2.046,3.407 2.743,3.577 0.698,0.170 10 Vent Valve 2.998,1.598 3.328,1.754 0.330,0.156 10 VCC 3.37,1.591 3.498,1.759 0.128,0.167 10 6 2.9,2.041 3.334,2.196 0.434,0.156 10 VOUT 3.37,2.05 3.485,2.206 0.114,0.156 10 7 2.9,2.733 3.348,2.889 0.448,0.156 10 SGND 3.377,2.513 3.477,2.669 0.100,0.156 10 8 2.886,3.197 3.334,3.367 0.448,0.170 10 VGND 1.443,3.195 1.835,3.351 0.392,0.156 10 VLVB 1.283,3.195 1.397,3.365 0.114,0.170 10 5 3.377,3.195 3.484,3.351 0.107,0.156 10 1 3.943,4.467 4.252,4.623 0.309,0.156 10 D16 3.943,4.605 4.683,4.761 0.739,0.156 10 Purge VSV 3.813,4.034 3.928,4.204 0.114,0.170 10 1 4.6,4.038 4.714,4.208 0.114,0.170 10 2 3.678,6.856 4.778,7.040 1.100,0.184 10 Integration Relay 1.408,5.374 2.064,5.544 0.656,0.170 10 EFI NO. 2 2.557,5.893 3.213,6.062 0.656,0.170 10 EFI NO. 1 3.482,6.417 4.112,6.573 0.630,0.156 10 EFI MAIN 2.238,5.756 2.456,5.923 0.218,0.166 10 1C 2.296,5.584 2.411,5.740 0.114,0.156 10 1 1.464,6.611 1.953,6.795 0.489,0.184 10 Battery 2.249,5.262 2.464,5.414 0.215,0.152 10 1B 2.725,6.663 2.940,6.816 0.215,0.152 10 1B 4.525,6.108 4.740,6.260 0.215,0.152 10 1B 2.293,5.096 2.407,5.258 0.114,0.162 10 4 4.574,5.937 4.689,6.106 0.114,0.170 10 2 2.527,6.663 2.641,6.819 0.114,0.156 10 3

CAUTION / NOTICE / HINT

NOTICE:
·

When a vehicle is brought into the workshop, leave it as it is. Do not change the vehicle condition. For example, do not tighten the fuel cap.

·

Do not disassemble the canister pump module.

·

The Techstream is required to conduct the following diagnostic troubleshooting procedure.



PROCEDURE

1.CONFIRM DTC AND EVAP PRESSURE
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON (do not start the engine).


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Vapor Pressure Pump.


g.

Read the EVAP (Evaporative Emission) pressure displayed on the Techstream.

Result
Display
(DTC Output)
Test Result Suspected Trouble Area Proceed to
P0451 - Canister pressure sensor C
P0452 Less than 42.11009 kPa-a (315.86779 mmHg-a)
·

Wire harness/connector (ECM - Canister pressure sensor)

·

Canister pressure sensor

·

Short in ECM circuit


A
P0453 More than 123.76147 kPa-a (928.33489 mmHg-a)
·

Wire harness/connector (ECM - Canister pressure sensor)

·

Canister pressure sensor

·

Open in ECM circuit


B



A

2.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)

B

4.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)

C

2.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the D56 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Result
Tester Connection Condition Specified Condition Suspected Trouble Area Proceed to
D56-121 (PPMP) - Body ground Always 10 Ω or less
·

Wire harness/connector (ECM - Canister pressure sensor)

·

Short in canister pressure sensor circuit


A
D56-121 (PPMP) - Body ground Always 10 kΩ or more
·

Wire harness/connector (ECM - Canister pressure sensor)

·

Short in ECM circuit


B



A

3.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)

B

7.REPLACE ECM
3.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
a.

Disconnect the O24 canister pump module connector.


b.

Disconnect the D56 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Result
Tester Connection Condition Specified Condition Suspected Trouble Area Proceed to
D56-121 (PPMP) - Body ground Always 10 kΩ or more Short in canister pressure sensor circuit A
D56-121 (PPMP) - Body ground Always 10 Ω or less Short in wire harness/connector (ECM - Canister pressure sensor) B



A

5.REPLACE CANISTER PUMP MODULE

B

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
a.

Disconnect the O24 canister pump module connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
O24-8 (SGND) - Body ground Always 100 Ω or less



c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
O24-6 (VCC) - Body ground Ignition switch ON 4.5 to 5.5 V
O24-7 (VOUT) - Body ground Ignition switch ON 4.5 to 5.5 V



Result
Test Result Suspected Trouble Area Proceed to
Voltage and resistance within standard ranges Open in canister pressure sensor circuit A
Voltage and resistance outside standard ranges Open in wire harness/connector (ECM - Canister pressure sensor) B


A

5.REPLACE CANISTER PUMP MODULE

B

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE CANISTER PUMP MODULE
a.

Replace the canister pump module (See page Engine / Hybrid System>3UR-FBE EMISSION CONTROL>CANISTER>REMOVAL).

NOTICE:
·

When replacing the canister pump module, check the canister pump module interior, canister interior and related pipes for water, fuel and other liquids. If liquids are present, check for disconnections and/or cracks in the following: 1) the pipe from the air inlet port to the canister pump module; 2) the canister filter; and 3) the fuel tank vent hose. If liquids are present in the canister interior, replace the canister and canister pump module together.

·

Check for filter blockage in the canister. If the charcoal filter inside the canister is clogged, replace the canister and canister pump module together.

·

Check for filter blockage in the canister filter. If the canister filter has blockages, replace the fuel tank inlet pipe sub-assembly.



U153146E03
2.583,4.01 3.563,4.365 true 3.656,5.104 5.292,5.104 false 3.156,2.552 5.292,2.552 false 5.01,2.604 5.01,5.042 false 1.938,6.073 1.938,6.323 false 3.802,5.333 3.802,6.323 false 3.719,6.365 1.99,6.365 false 1.563,5.323 2.01,6.188 true 3.615,5.656 4.313,6.229 4.313,6.229 3.323,5.854 false 5.083,3.583 6.156,3.865 1.073,0.281 10 false Inspection Area* 2.323,6.396 3.396,6.677 1.073,0.281 10 false Inspection Area* 4.354,6.167 5.042,6.49 0.688,0.323 10 false Vent Hose 0.781,5.177 1.583,5.448 0.802,0.271 10 false Air Inlet Port 1.271,3.906 2.594,4.25 1.323,0.344 10 false Fuel Tank Vent Hose 4.51,0.188 7.063,0.573 2.552,0.385 10 false *: Check for disconnection and/or cracks



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
HINT:

If the exhaust tailpipe has been removed, go to the next step before reinstalling it.



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)
7.REPLACE ECM

NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)
8.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.


c.

Wait for at least 60 seconds.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


HINT:

If no pending DTCs are displayed on the Techstream, the repair has been successfully completed.



NEXT

COMPLETED