CHECK ECM
Measure the voltage according to the value(s) in the table below.
The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A27-1 (BATT) - D56-81 (E1) | L - BR | Battery (for measuring battery voltage and for ECM memory) | Always | 11 to 14 V |
| D56-41 (+BM) - D56-81 (E1) | P - BR | Power source of throttle actuator | Always | 11 to 14 V |
| A27-28 (IGSW) - D56-81 (E1) | LG - BR | Ignition switch | Ignition switch ON | 11 to 14 V |
| A27-3 (+B) - D56-81 (E1) | GR - BR | Power source of ECM | Ignition switch ON | 11 to 14 V |
| A27-2 (+B2) - D56-81 (E1) | GR - BR | Power source of ECM | Ignition switch ON | 11 to 14 V |
| D56-58 (OC1+) - D56-57 (OC1-) | B - B-L | Camshaft timing oil control valve (OCV) (for Intake Side of Bank 1) | Idling | Pulse generation
(see waveform 1) |
| D56-52 (OC2+) - D56-51 (OC2-) | L-B - R-B | Camshaft timing oil control valve (OCV) (for Intake Side of Bank 2) | Idling | Pulse generation
(see waveform 1) |
| D56-56 (OE1+) - D56-55 (OE1-) | L-W - L-B | Camshaft timing oil control valve (OCV) (for Exhaust Side of Bank 1) | Idling | Pulse generation
(see waveform 1) |
| D56-50 (OE2+) - D56-49 (OE2-) | L-R - L | Camshaft timing oil control valve (OCV) (for Exhaust Side of Bank 2) | Idling | Pulse generation
(see waveform 1) |
| A27-34 (MREL) - D56-81 (E1) | W - BR | EFI MAIN relay | Ignition switch ON | 11 to 14 V |
| D56-74 (VG) - D56-75 (E2G) | L-Y - G-W | Mass air flow meter | Idling, Shift lever position P or N, A/C switch OFF | 0.5 to 3.0 V |
| D56-73 (THA) - D56-97 (ETHW) | Y-B - BR | Intake air temperature sensor | Idling, Intake air temperature 20°C (68°F) | 0.5 to 3.4 V |
| D56-76 (THW) - D56-98 (ETHA) | G-B - BR | Engine coolant temperature sensor | Idling, Engine coolant temperature 80°C (176°F) | 0.2 to 1.0 V |
| D56-80 (VCTA) - D56-79 (ETA) | Y - L | Power source of throttle position sensor (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| D56-78 (VTA1) - D56-79 (ETA) | R-Y - L | Throttle position sensor (for engine control) | Ignition switch ON,
Throttle valve fully closed |
0.5 to 1.1 V |
| Ignition switch ON,
Throttle valve fully open |
3.2 to 4.8 V | |||
| D56-77 (VTA2) - D56-79 (ETA) | Y-B - L | Throttle position sensor (for sensor malfunction detection) | Ignition switch ON,
Throttle valve fully closed |
2.1 to 3.1 V |
| Ignition switch ON,
Throttle valve fully open |
4.6 to 5.0 V | |||
| A27-55 (VPA) - A27-58 (EPA) | W - BE | Accelerator pedal position sensor (for engine control) | Ignition switch ON,
Accelerator pedal released |
0.5 to 1.1 V |
| Ignition switch ON,
Accelerator pedal fully depressed |
2.6 to 4.5 V | |||
| A27-56 (VPA2) - A27-60 (EPA2) | LG - BR | Accelerator pedal position sensor (for sensor malfunctioning detection) | Ignition switch ON,
Accelerator pedal released |
1.2 to 2.0 V |
| Ignition switch ON,
Accelerator pedal fully depressed |
3.4 to 4.7 V | |||
| A27-57 (VCPA) - A27-58 (EPA) | B - BE | Power source of accelerator pedal position sensor (for VPA) | Ignition switch ON | 4.5 to 5.5 V |
| A27-59 (VCP2) - A27-60 (EPA2) | V - BR | Power source of accelerator pedal position sensor (for VPA2) | Ignition switch ON | 4.5 to 5.5 V |
| D56-22 (HA1A) - D56-23 (E04) | L - W-B | A/F sensor heater (for Bank 1 Sensor 1) | Idling | Below 3.0 V |
| Ignition switch ON | 11 to 14 V | |||
| D56-20 (HA2A) - D56-21 (E05) | G - W-B | A/F sensor heater (for Bank 2 Sensor 1) | Idling | Below 3.0 V |
| Ignition switch ON | 11 to 14 V | |||
| D56-126 (A1A+) - D56-81 (E1) | G -BR | A/F sensor (for Bank 1 Sensor 1) | Ignition switch ON | 3.3 V* |
| D56-125 (A1A-) - D56-81 (E1) | R - BR | A/F sensor (for Bank 1 Sensor 1) | Ignition switch ON | 2.9 V* |
| D56-103 (A2A+) - D56-81 (E1) | P - BR | A/F sensor (for Bank 2 Sensor 1) | Ignition switch ON | 3.3 V* |
| D56-102 (A2A-) - D56-81 (E1) | L - BR | A/F sensor (for Bank 2 Sensor 1) | Ignition switch ON | 2.9 V* |
| D56-45 (HT1B) - D56-46 (E03) | G-B - W-B | Heated oxygen sensor heater | Idling | Below 3.0 V |
| Ignition switch ON | 11 to 14 V | |||
| D56-44 (HT2B) - D56-46 (E03) | B - W-B | Heated oxygen sensor heater | Idling | Below 3.0 V |
| Ignition switch ON | 11 to 14 V | |||
| D56-114 (OX1B) - D56-115 (EX1B) | G - L | Heated oxygen sensor | Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor | Pulse generation
(see waveform 2) |
| D56-112 (OX2B) - D56-113 (EX2B) | R - W | Heated oxygen sensor | Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor | Pulse generation
(see waveform 2) |
| D56-86 (#10) - D56-43 (E01) | R-L - W-B | Fuel injector | Ignition switch ON | 11 to 14 V |
| Idling | Pulse generation
(see waveform 3) |
|||
| D56-109 (#20) - D56-43 (E01) | L - W-B | Fuel injector | Ignition switch ON | 11 to 14 V |
| Idling | Pulse generation
(see waveform 3) |
|||
| D56-85 (#30) - D56-43 (E01) | R - W-B | Fuel injector | Ignition switch ON | 11 to 14 V |
| Idling | Pulse generation
(see waveform 3) |
|||
| D56-108 (#40) - D56-43 (E01) | Y - W-B | Fuel injector | Ignition switch ON | 11 to 14 V |
| Idling | Pulse generation
(see waveform 3) |
|||
| D56-84 (#50) - D56-43 (E01) | G - W-B | Fuel injector | Ignition switch ON | 11 to 14 V |
| Idling | Pulse generation
(see waveform 3) |
|||
| D56-107 (#60) - D56-43 (E01) | R - W-B | Fuel injector | Ignition switch ON | 11 to 14 V |
| Idling | Pulse generation
(see waveform 3) |
|||
| D56-83 (#70) - D56-43 (E01) | W - W-B | Fuel injector | Ignition switch ON | 11 to 14 V |
| Idling | Pulse generation
(see waveform 3) |
|||
| D56-106 (#80) - D56-43 (E01) | R-B - W-B | Fuel injector | Ignition switch ON | 11 to 14 V |
| Idling | Pulse generation
(see waveform 3) |
|||
| D56-94 (KNK1) - D56-93 (EKNK) | R - G | Knock sensor | Engine speed maintained at 4000 rpm after warming up engine | Pulse generation
(see waveform 4) |
| D56-117 (KNK2) - D56-116 (EKN2) | W - B | Knock sensor | Engine speed maintained at 4000 rpm after warming up engine | Pulse generation
(see waveform 4) |
| D56-96 (KNK3) - D56-95 (EKN3) | W - B | Knock sensor | Engine speed maintained at 4000 rpm after warming up engine | Pulse generation
(see waveform 4) |
| D56-119 (KNK4) - D56-118 (EKN4) | R - G | Knock sensor | Engine speed maintained at 4000 rpm after warming up engine | Pulse generation
(see waveform 4) |
| D56-92 (VV1+) - D56-91 (VV1-) | R - G | Variable valve timing (VVT) sensor (for Intake Side of Bank 1) | Idling | Pulse generation
(see waveform 5) |
| D56-87 (VV2+) - D56-88 (VV2-) | R - Y | Variable valve timing (VVT) sensor (for Intake Side for Bank 2) | Idling | Pulse generation
(see waveform 5) |
| D56-69 (EV1+) - D56-68 (EV1-) | R-L - B | Variable valve timing (VVT) sensor (for Exhaust Side of Bank 1) | Idling | Pulse generation
(see waveform 16) |
| D56-64 (EV2+) - D56-65 (EV2-) | R-L - B | Variable valve timing (VVT) sensor (for Exhaust Side of Bank 2) | Idling | Pulse generation
(see waveform 16) |
| D56-110 (NE+) - D56-111 (NE-) | W - Y | Crankshaft position sensor | Idling | Pulse generation
(see waveform 5) |
| D56-40 (IGT1) - D56-81 (E1) | B-Y - BR | Ignition coil (ignition signal) | Idling | Pulse generation
(see waveform 6) |
| D56-33 (IGT2) - D56-81 (E1) | L-Y - BR | Ignition coil (ignition signal) | Idling | Pulse generation
(see waveform 6) |
| D56-37 (IGT3) - D56-81 (E1) | B - BR | Ignition coil (ignition signal) | Idling | Pulse generation
(see waveform 6) |
| D56-34 (IGT4) - D56-81 (E1) | L-B - BR | Ignition coil (ignition signal) | Idling | Pulse generation
(see waveform 6) |
| D56-35 (IGT5) - D56-81 (E1) | G-R - BR | Ignition coil (ignition signal) | Idling | Pulse generation
(see waveform 6) |
| D56-36 (IGT6) - D56-81 (E1) | G - BR | Ignition coil (ignition signal) | Idling | Pulse generation
(see waveform 6) |
| D56-38 (IGT7) - D56-81 (E1) | G-W - BR | Ignition coil (ignition signal) | Idling | Pulse generation
(see waveform 6) |
| D56-39 (IGT8) - D56-81 (E1) | G-B - BR | Ignition coil (ignition signal) | Idling | Pulse generation
(see waveform 6) |
| D56-104 (IGF1) - D56-81 (E1) | G-B - BR | Ignition coil (ignition confirmation signal) | Ignition switch ON | 4.5 to 5.5 V |
| Idling | Pulse generation
(see waveform 6) |
|||
| D56-105 (IGF2) - D56-81 (E1) | R - BR | Ignition coil (ignition confirmation signal) | Ignition switch ON | 4.5 to 5.5 V |
| Idling | Pulse generation
(see waveform 6) |
|||
| D56-63 (PRG) - D56-81 (E1) | L-B - BR | Purge VSV | Ignition switch ON | 11 to 14 V |
| Idling | Pulse generation
(see waveform 7) |
|||
| A27-13 (SPD) - D56-81 (E1) | B - BR | Speed signal from combination meter | Driving at 20 km/h (12 mph) | Pulse generation
(see waveform 8) |
| A27-46 (STA) - D56-81 (E1) | R - BR | Starter signal | Cranking | 5.5 V or more |
| D56-120 (NSW) - D56-81 (E1) | L - BR | Park/Neutral position switch | Ignition switch ON, Shift lever position other than P and N | 11 to 14 V |
| Ignition switch ON, Shift lever position in P or N | Below 3.0 V | |||
| A27-26 (STP) - D56-81 (E1) | LG - BR | Stop light switch | Brake pedal depressed | 7.5 to 14 V |
| Brake pedal released | Below 1.5 V | |||
| A27-35 (ST1-) - D56-81 (E1) | R - BR | Stop light switch
(opposite to STP terminal) |
Ignition switch ON,
Brake pedal depressed |
Below 1.5 V |
| Ignition switch ON,
Brake pedal released |
7.5 to 14 V | |||
| D56-19 (M+) - D56-82 (ME01) | R - W-B | Throttle actuator | Idling with warm engine | Pulse generation
(see waveform 9) |
| D56-18 (M-) - D56-82 (ME01) | G - W-B | Throttle actuator | Idling with warm engine | Pulse generation
(see waveform 10) |
| A27-48 (FC) - D56-81 (E1) | L - BR | Fuel pump control | Ignition switch ON | 11 to 14 V |
| A27-52 (FPC) - D56-81 (E1) | BE - BR | Fuel pump control | Ignition switch ON | Below 1.5 V |
| A27-24 (W) - D56-81 (E1) | P - BR | MIL | Ignition switch ON | Below 3.0 V |
| Idling | 11 to 14 V | |||
| A27-16 (TC) - D56-81 (E1) | R - BR | Terminal TC of DLC3 | Ignition switch ON | 11 to 14 V |
| A27-15 (TACH) - D56-81 (E1) | W - BR | Engine speed | Idling | Pulse generation
(see waveform 11) |
| A27-30 (VPMP) - D56-81 (E1) | V - BR | Vent valve (built into canister pump module) | Ignition switch ON | 11 to 14 V |
| A27-49 (MPMP) - D56-81 (E1) | G - BR | Leak detection pump (built into canister pump module) | Leak detection pump OFF | Below 3.0 V |
| Leak detection pump ON | 11 to 14 V | |||
| D56-67 (VCV1) - D56-97 (ETHW) | L - BR | Power source for sensor (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| D56-66 (VCV2) - D56-97 (ETHW) | L - BR | Power source for sensor (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
| D56-121 (PPMP) - D56-97 (ETHW) | P - BR | Canister pressure sensor (built into canister pump module) | Ignition switch ON | 3.3 to 4.0 V |
| D56-32 (ALT) - D56-81 (E1) | R - BR | Generator | Ignition switch ON | 11 to 14 V |
| A27-10 (CANH) - D56-81 (E1) | GR - BR | CAN communication line | Ignition switch ON | Pulse generation
(see waveform 12) |
| A27-11 (CANL) - D56-81 (E1) | W - BR | CAN communication line | Ignition switch ON | Pulse generation
(see waveform 13) |
| D56-62 (ACIS) - D56-81 (E1) | L-Y - BR | VSV for ACIS (Acoustic Control Induction System) operation signal | Ignition switch ON | 11 to 14 V |
| D56-28 (AIRV) - D56-81 (E1) | BR - BR | Air switching valve for secondary air injection system | Ignition switch ON | 11 to 14 V |
| D56-54 (AIRP) - D56-81 (E1) | P - BR | Air pump control | Ignition switch ON | 11 to 14 V |
| D56-30 (AIDI) - D56-81 (E1) | G - BR | Diagnostic information signal for secondary air injection system | Air injection system operates | Pulse generation
(see waveform 15) |
| A27-54 (AIP) - D56-98 (ETHA) | Y - BR | Secondary air injection system pressure signal | Ignition switch ON | 3.0 to 3.6 V |
| A27-43 (ARV2) - D56-81 (E1) | V - BR | Air switching valve for secondary air injection system | Ignition switch ON | 11 to 14 V |
| D56-53 (ARP2) - D56-81 (E1) | P-L - BR | Air pump control | Ignition switch ON | 11 to 14 V |
| D56-29 (AID2) - D56-81 (E1) | G-Y - BR | Diagnostic information signal for secondary air injection system | Air injection system operates | Pulse generation
(see waveform 15) |
| A27-53 (AIP2) - D56-97 (ETHW) | G - BR | Secondary air injection system pressure signal | Ignition switch ON | 3.0 to 3.6 V |
| D56-90 (G2) - D56-89 (G2-) | R - B | Camshaft position sensor | Idling | Pulse generation
(see waveform 14) |
| A27-18 (DI) - D56-81 (E1) | Y - BR | Fuel pump control | Ignition switch ON | 0 to 3.0 V |
| A27-14 (STSW) - D56-81 (E1) | BR - BR | Ignition switch signal | Shift lever position P or N, Cranking | 6.0 V or more |
| A27-41 (ACCR) - D56-81 (E1) | BR - BR | ACC relay control signal | Ignition switch ON → Cranking | 11 to 14 V → Below 1 V |
| D56-16 (STAR) - D56-81 (E1) | L - BR | ST relay control | Ignition switch ON | Below 1.5 V |
| Cranking | 5.5 V or more | |||
| D56-72 (PSP) - D56-81 (E1) | G - BR | Power steering oil pressure sensor | Ignition switch ON | 0.3 to 4.7 V |
| D56-60 (FPCR) - D56-81 (E1) | R - BR | Fuel pressure switching valve | Fuel pressure switching valve OFF | 11 to 14 V |
| D56-61 (HAI1) - D56-81 (E1) | B - BR | Air pump heater for secondary air injection system | AI heater operating | Below 1.5 V |
| A27-33 (ELS2) - D56-81 (E1) | B - BR | Electric load | Rear defogger switch on | 7.5 to 14 V |
| Rear defogger switch off | Below 1.5 V |
*: The ECM terminal voltage is constant regardless of the output voltage from the sensor.
WAVEFORM 1:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| D56-58 (OC1+) - D56-57 (OC1-) | 5 V/DIV., 1 msec./DIV. | Idling |
| D56-52 (OC2+) - D56-51 (OC2-) | 5 V/DIV., 1 msec./DIV. | Idling |
| D56-56 (OE1+) - D56-55 (OE1-) | 5 V/DIV., 1 msec./DIV. | Idling |
| D56-50 (OE2+) - D56-49 (OE2-) | 5 V/DIV., 1 msec./DIV. | Idling |
WAVEFORM 2:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| D56-114 (OX1B) - D56-115 (EX1B) | 0.2 V/DIV., 200 msec./DIV. | Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor |
| D56-112 (OX2B) - D56-113 (EX2B) | 0.2 V/DIV., 200 msec./DIV. | Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor |
In Data List, item O2S B1S2 and O2S B2S2 show the ECM input values from the heated oxygen sensor.
WAVEFORM 3:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| D56-86 (#10) - D56-43 (E01) | 20 V/DIV., 20 msec./DIV. | Idling |
| D56-109 (#20) - D56-43 (E01) | 20 V/DIV., 20 msec./DIV. | Idling |
| D56-85 (#30) - D56-43 (E01) | 20 V/DIV., 20 msec./DIV. | Idling |
| D56-108 (#40) - D56-43 (E01) | 20 V/DIV., 20 msec./DIV. | Idling |
| D56-84 (#50) - D56-43 (E01) | 20 V/DIV., 20 msec./DIV. | Idling |
| D56-107 (#60) - D56-43 (E01) | 20 V/DIV., 20 msec./DIV. | Idling |
| D56-83 (#70) - D56-43 (E01) | 20 V/DIV., 20 msec./DIV. | Idling |
| D56-106 (#80) - D56-43 (E01) | 20 V/DIV., 20 msec./DIV. | Idling |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 4:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| D56-94 (KNK1) - D56-93 (EKNK) | 1 V/DIV., 1 msec./DIV. | Engine speed maintained at 4000 rpm after warming up engine |
| D56-117 (KNK2) - D56-116 (EKN2) | 1 V/DIV., 1 msec./DIV. | Engine speed maintained at 4000 rpm after warming up engine |
| D56-96 (KNK3) - D56-95 (EKN3) | 1 V/DIV., 1 msec./DIV. | Engine speed maintained at 4000 rpm after warming up engine |
| D56-119 (KNK4) - D56-118 (EKN4) | 1 V/DIV., 1 msec./DIV. | Engine speed maintained at 4000 rpm after warming up engine |
The wavelength becomes shorter as the engine speed increases.
The waveforms and amplitudes displayed differ slightly depending on the vehicle.
WAVEFORM 5:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| (a) D56-110 (NE+) - D56-111 (NE-) | 5 V/DIV., 20 msec./DIV. | Idle after engine warmed up |
| (b) D56-92 (VV1+) - D56-91 (VV1-) | 5 V/DIV., 20 msec./DIV. | Idle after engine warmed up |
| (c) D56-87 (VV2+) - D56-88 (VV2-) | 5 V/DIV., 20 msec./DIV. | Idle after engine warmed up |
The wavelength becomes shorter as engine speed increases.
WAVEFORM 6:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| (a) D56-40 (IGT1) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
| (a) D56-33 (IGT2) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
| (a) D56-37 (IGT3) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
| (a) D56-34 (IGT4) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
| (a) D56-35 (IGT5) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
| (a) D56-36 (IGT6) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
| (a) D56-38 (IGT7) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
| (a) D56-39 (IGT8) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
| (b) D56-104 (IGF1) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
| (b) D56-105 (IGF2) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Idling |
The wavelength becomes shorter as engine speed increases.
WAVEFORM 7:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| D56-63 (PRG) - D56-81 (E1) | 10 V/DIV., 20 msec./DIV. | Idling |
If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.
WAVEFORM 8:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| A27-13 (SPD) - D56-81 (E1) | 2 V/DIV., 20 msec./DIV. | Driving at 20 km/h (12 mph) |
The wavelength becomes shorter as the vehicle speed increases.
WAVEFORM 9:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| D56-19 (M+) - D56-82 (ME01) | 5 V/DIV., 1 msec./DIV. | Idling with warm engine |
The duty ratio varies depending on the throttle actuator operation.
WAVEFORM 10:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| D56-18 (M-) - D56-82 (ME01) | 5 V/DIV., 1 msec./DIV. | Idling with warm engine |
The duty ratio varies depending on the throttle actuator operation.
WAVEFORM 11:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| A27-15 (TACH) - D56-81 (E1) | 5 V/DIV., 10 msec./DIV. | Idling |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 12:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| A27-10 (CANH) - D56-81 (E1) | 1 V/DIV., 10 μsec./DIV. | Engine stops and ignition switch ON |
The waveform varies depending on the CAN communication signal.
WAVEFORM 13:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| A27-11 (CANL) - D56-81 (E1) | 1 V/DIV., 10 μsec./DIV. | Engine stops and ignition switch ON |
The waveform varies depending on the CAN communication signal.
WAVEFORM 14:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| CH1: D56-110 (NE+) - D56-111 (NE-) | 5 V/DIV., 20 msec./DIV. | Idle after engine warmed up |
| CH2: D56-90 (G2) - D56-89 (G2-) | 5 V/DIV., 20 msec./DIV. | Idle after engine warmed up |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 15:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| D56-30 (AIDI) - D56-81 (E1) | 5 V/DIV., 50 msec./DIV. | Performing system check using Techstream (secondary air injection check) |
| D56-29 (AID2) - D56-81 (E1) | 5 V/DIV., 50 msec./DIV. | Performing system check using Techstream (secondary air injection check) |
The wavelength changes when the air injection control driver detects malfunctions in the secondary air injection system (see page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>P0412).
WAVEFORM 16:
| Terminal No. (Symbol) | Tool Setting | Condition |
|---|---|---|
| (a) D56-110 (NE+) - D56-111 (NE-) | 5 V/DIV., 20 msec./DIV. | Idle after engine warmed up |
| (b) D56-69 (EV1+) - D56-68 (EV1-) | 5 V/DIV., 20 msec./DIV. | Idle after engine warmed up |
| (c) D56-64 (EV2+) - D56-65 (EV2-) | 5 V/DIV., 20 msec./DIV. | Idle after engine warmed up |
The wavelength becomes shorter as engine speed increases.