Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM
RM27L0U _51 Engine / Hybrid System _049293 3UR-FBE ENGINE CONTROL _0235531 SFI SYSTEM C

3UR-FBE ENGINE CONTROL  SFI SYSTEM  P0112  Intake Air Temperature Circuit Low Input  P0113  Intake Air Temperature Circuit High Input  


DESCRIPTION

A371036E02
1.802,2.26 2.219,1.844 false 0.104,0.083 0.583,0.281 0.479,0.198 10 false Fig. 1 0.135,0.396 1.198,0.594 1.063,0.198 10 false Resistance 2.042,1.656 2.844,1.854 0.802,0.198 10 false Acceptable 0.469,0.802 0.74,0.99 0.271,0.188 10 false 30 0.469,1.01 0.74,1.198 0.271,0.188 10 false 20 0.469,1.313 0.74,1.5 0.271,0.188 10 false 10 0.469,3.479 0.74,3.667 0.271,0.188 10 false 0.1 0.469,3.156 0.74,3.344 0.271,0.188 10 false 0.2 0.458,2.833 0.729,3.021 0.271,0.188 10 false 0.3 0.458,2.646 0.729,2.833 0.271,0.188 10 false 0.5 0.542,2.385 0.719,2.573 0.177,0.188 10 false 1 0.542,2.063 0.719,2.25 0.177,0.188 10 false 2 0.542,1.875 0.719,2.063 0.177,0.188 10 false 3 0.552,1.646 0.729,1.833 0.177,0.188 10 false 5 0.813,3.865 1.083,4.052 0.271,0.188 10 false -20 1.208,3.865 1.479,4.052 0.271,0.188 10 false 0 1.531,3.865 1.802,4.052 0.271,0.188 10 false 20 1.854,3.865 2.125,4.052 0.271,0.188 10 false 40 2.167,3.865 2.438,4.052 0.271,0.188 10 false 60 2.542,3.865 2.813,4.052 0.271,0.188 10 false 80 2.865,3.865 3.135,4.052 0.271,0.188 10 false 100 0.802,4.021 1.104,4.208 0.302,0.188 10 false (-4) 1.125,4.021 1.427,4.208 0.302,0.188 10 false (32) 1.479,4.021 1.781,4.208 0.302,0.188 10 false (68) 1.771,4.021 2.135,4.219 0.365,0.198 10 false (104) 2.104,4.021 2.469,4.219 0.365,0.198 10 false (140) 2.458,4.021 2.823,4.219 0.365,0.198 10 false (176) 2.833,4.031 3.198,4.229 0.365,0.198 10 false (212) 1.365,4.25 2.688,4.458 1.323,0.208 10 false Temperature °C (°F) 0.073,0.729 0.417,0.948 0.344,0.219 10 false (kΩ)

The Intake Air Temperature (IAT) sensor, mounted on the Mass Air Flow (MAF) meter, monitors the IAT. The IAT sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the IAT is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (See Fig. 1).

The IAT sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.

Resistor R and the IAT sensor are connected in series. When the resistance value of the IAT sensor changes, according to changes in the IAT, the voltage at terminal THA also varies. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.

HINT:

When DTC P0112 or P0113 is set, the ECM enters fail-safe mode. During fail-safe mode, the IAT is estimated to be 20°C (68°F) by the ECM. Fail-safe mode continues until a pass condition is detected.



DTC No. DTC Detection Condition Trouble Area
P0112 Short in IAT sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Short in IAT sensor circuit

·

IAT sensor (built into MAF meter)

·

ECM


P0113 Open in IAT sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Open in IAT sensor circuit

·

IAT sensor (built into MAF meter)

·

ECM



HINT:

When any of these DTCs are set, check the IAT by entering the following menus: Powertrain / Engine and ECT / All Data / Intake Air.

Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or higher Short circuit


MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to calculate the IAT. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the IAT sensor and stores a DTC.

Example:

If the sensor output voltage is more than 4.91 V for 0.5 seconds or more, the ECM determines that there is an open in the IAT sensor circuit, and sets DTC P0113. Conversely, if the output voltage is less than 0.18 V for 0.5 seconds or more, the ECM determines that there is a short in the sensor circuit, and sets DTC P0112.

If the malfunction is not repaired successfully, a DTC is stored 0.5 seconds after the engine is next started.

MONITOR STRATEGY

Related DTCs P0112: IAT sensor range check (Low voltage)
P0113: IAT sensor range check (High voltage)
Required Sensors/Components (Main) IAT sensor
Required Sensors/Components (Related) -
Frequency of Operation Continuous
Duration 0.5 seconds
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs not present None
Battery voltage 8 V or more
Ignition switch ON
Starter OFF

TYPICAL MALFUNCTION THRESHOLDS

P0112:
IAT sensor voltage [IAT] Less than 0.18 V [More than 128°C (262°F)]

P0113:
IAT sensor voltage [IAT] More than 4.91 V [Less than -55°C (-67°F)]

COMPONENT OPERATING RANGE

IAT sensor voltage [IAT] 0.18 to 4.91 V [-55 to 128°C (-67 to 262°F)]

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Wait 0.5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTC.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0112 or P0113.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



12.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A178643E01
0.402,1.816 0.607,1.979 0.205,0.163 10 D3 0.403,1.991 2.531,2.161 2.128,0.170 10 IAT Sensor (Built into MAF Meter) 2.07,0.61 2.399,0.749 0.330,0.139 10 THA 2.175,1.227 2.379,1.369 0.205,0.142 10 E2 2.431,0.608 2.553,0.770 0.121,0.163 10 4 2.431,1.224 2.553,1.387 0.121,0.163 10 5 5.185,0.713 5.473,0.883 0.288,0.170 10 D56 5.185,1.329 5.473,1.499 0.288,0.170 10 D56 5.231,0.543 5.414,0.696 0.184,0.152 10 73 5.231,1.16 5.414,1.312 0.184,0.152 10 97 5.521,0.609 5.851,0.751 0.330,0.142 10 THA 5.521,1.233 6.003,1.375 0.482,0.142 10 ETHW 5.958,2.24 6.323,2.413 0.364,0.173 10 ECM 6.246,0.243 6.513,0.406 0.267,0.163 10 5 V

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING TECHSTREAM (INTAKE AIR TEMPERATURE)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / All Data / Intake Air.


e.

Read the value displayed on the Techstream.

Standard:

Same as actual Intake Air Temperature (IAT).


Result
Temperature Displayed Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
Same as actual IAT C

HINT:
·

If there is an open circuit, the Techstream indicates -40°C (-40°F).


·

If there is a short circuit, the Techstream indicates 140°C (284°F) or higher.





A

2.READ VALUE USING TECHSTREAM (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING TECHSTREAM (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING TECHSTREAM (CHECK FOR OPEN IN WIRE HARNESS)
U152964E02
1.313,4 1.885,3.469 true 1.875,4 2.031,3.458 true 0.406,1.667 1.156,1.844 0.75,0.177 10 false MAF Meter 2.583,1.677 2.938,1.854 0.354,0.177 10 false ECM 2.448,1 2.781,1.156 0.333,0.156 10 false THA 2.448,1.188 2.906,1.333 0.458,0.146 10 false ETHW 0.417,3.323 0.615,3.49 0.198,0.167 10 false D3 1.552,0.688 1.75,0.854 0.198,0.167 10 false D3 1.083,4.021 1.417,4.177 0.333,0.156 10 false THA 1.75,4.021 1.969,4.177 0.219,0.156 10 false E2 0.083,2.083 2.458,2.448 2.375,0.365 10 false Front view of wire harness connector: (to MAF Meter) 1.802,1.021 1.927,1.167 0.125,0.146 10 false 4 1.802,1.406 1.927,1.552 0.125,0.146 10 false 5

a.

Disconnect the D3 MAF meter connector.


b.

Connect terminals 4 (THA) and 5 (E2) of the MAF meter wire harness side connector.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the Techstream on.


f.

Enter the following menus: Powertrain / Engine and ECT / All Data / Intake Air.


g.

Read the value displayed on the Techstream.

Standard value:

140°C (284°F) or higher


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER

NG

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the D3 MAF meter connector.


b.

Disconnect the D56 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D3-4 (THA) - D56-73 (THA) Always Below 1 Ω
D3-5 (E2) - D56-97 (ETHW) Always Below 1 Ω




OK

CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING TECHSTREAM (CHECK FOR SHORT IN WIRE HARNESS)
U153065E02
1.479,0.719 1.677,0.896 0.198,0.177 10 false D3 0.375,1.656 1.094,1.813 0.719,0.156 10 false MAF Meter 2.542,1.698 2.875,1.854 0.333,0.156 10 false ECM 2.458,1.49 2.906,1.646 0.448,0.156 10 false ETHW 2.51,1.042 2.823,1.198 0.313,0.156 10 false THA

a.

Disconnect the D3 MAF meter connector.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the Techstream on.


e.

Enter the following menus: Powertrain / Engine and ECT / All Data / Intake Air.


f.

Read the value displayed on the Techstream.

Standard value:

-40°C (-40°F)


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the D3 MAF meter connector.


b.

Disconnect the D56 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D3-4 (THA) or D56-73 (THA) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR