Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM
RM27L0U _51 Engine / Hybrid System _049293 3UR-FBE ENGINE CONTROL _0235531 SFI SYSTEM C

3UR-FBE ENGINE CONTROL  SFI SYSTEM  P0327  Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)  P0328  Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)  P032C  Knock Sensor 3 Circuit Low  P032D  Knock Sensor 3 Circuit High  P0332  Knock Sensor 2 Circuit Low Input (Bank 2)  P0333  Knock Sensor 2 Circuit High Input (Bank 2)  P033C  Knock Sensor 4 Circuit Low Input  P033D  Knock Sensor 4 Circuit High Input  


DESCRIPTION

A flat type knock sensor (non-resonant type) has a structure that can detect vibrations between approximately 5 kHz and 15 kHz.

Knock sensors are fitted onto the engine block to detect engine knocking.

The knock sensor contains a piezoelectric element which generates a voltage when it becomes deformed.

The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.

DTC No. DTC Detection Condition Trouble Area
P0327 Output voltage of knock sensor (for Bank 1 Sensor 1) is 0.5 V or less
(1 trip detection logic)
·

Short in knock sensor (for Bank 1 Sensor 1) circuit


·

Knock sensor (for Bank 1 Sensor 1)


·

ECM


P0328 Output voltage of knock sensor (for Bank 1 Sensor 1) is 4.5 V or more
(1 trip detection logic)
·

Open in knock sensor (for Bank 1 Sensor 1) circuit


·

Knock sensor (for Bank 1 Sensor 1)


·

ECM


P0332 Output voltage of knock sensor (for Bank 2 Sensor 1) is 0.5 V or less
(1 trip detection logic)
·

Short in knock sensor (for Bank 2 Sensor 1) circuit


·

Knock sensor (for Bank 2 Sensor 1)


·

ECM


P0333 Output voltage of knock sensor (for Bank 2 Sensor 1) is 4.5 V or more
(1 trip detection logic)
·

Open in knock sensor (for Bank 2 Sensor 1) circuit


·

Knock sensor (for Bank 2 Sensor 1)


·

ECM


P032C Output voltage of knock sensor (for Bank 1 Sensor 2) is 0.5 V or less
(1 trip detection logic)
·

Short in knock sensor (for Bank 1 Sensor 2) circuit


·

Knock sensor (for Bank 1 Sensor 2)


·

ECM


P032D Output voltage of knock sensor (for Bank 1 Sensor 2) is 4.5 V or more
(1 trip detection logic)
·

Open in knock sensor (for Bank 1 Sensor 2) circuit


·

Knock sensor (for Bank 1 Sensor 2)


·

ECM


P033C Output voltage of knock sensor (for Bank 2 Sensor 2) is 0.5 V or less
(1 trip detection logic)
·

Short in knock sensor (for Bank 2 Sensor 2) circuit


·

Knock sensor (for Bank 2 Sensor 2)


·

ECM


P033D Output voltage of knock sensor (for Bank 2 Sensor 2) is 4.5 V or more
(1 trip detection logic)
·

Open in knock sensor (for Bank 2 Sensor 2) circuit


·

Knock sensor (for Bank 2 Sensor 2)


·

ECM



HINT:

When DTC P0327, P0328, P0332, P0333, P032C, P032D, P033C or P033D is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the ignition switch is turned off.


Reference: Inspection using an oscilloscope

A150243E01
0.336,0.512 1.924,0.727 1.588,0.215 10 KNK1 Signal Waveform 2.632,1.857 2.985,2.060 0.353,0.203 10 GND 2.503,1.065 3.067,1.268 0.564,0.203 10 1 V/DIV. 0.915,2.821 1.757,3.024 0.842,0.203 10 1 msec./DIV.

Standard:
Tester Connection Tool Setting Condition Specified Condition
D56-94 (KNK1) - D56-93 (EKNK) 1 V/DIV.
1 msec./DIV.
Keep engine speed at 4000 rpm with warm engine The correct waveform is as shown
D56-117 (KNK2) - D56-116 (EKN2) 1 V/DIV.
1 msec./DIV.
Keep engine speed at 4000 rpm with warm engine The correct waveform is as shown
D56-96 (KNK3) - D56-95 (EKN3) 1 V/DIV.
1 msec./DIV.
Keep engine speed at 4000 rpm with warm engine The correct waveform is as shown
D56-119 (KNK4) - D56-118 (EKN4) 1 V/DIV.
1 msec./DIV.
Keep engine speed at 4000 rpm with warm engine The correct waveform is as shown


MONITOR DESCRIPTION

The knock sensor, located on the cylinder block, detects spark knock. When spark knock occurs, the piezoelectric element of the sensor vibrates. When the ECM detects a voltage in this frequency range, it retards the ignition timing to suppress the spark knock.

The ECM also senses background engine noise with the knock sensor and uses this noise to check for faults in the sensor. If the knock sensor output voltage is outside the normal range, the ECM interprets this as a fault in the knock sensor and stores a DTC.

MONITOR STRATEGY

Related DTCs P0327: Knock sensor (for Bank 1 Sensor 1) open/short (Low voltage)
P0328: Knock sensor (for Bank 1 Sensor 1) open/short (High voltage)
P0332: Knock sensor (for Bank 2 Sensor 1) open/short (Low voltage)
P0333: Knock sensor (for Bank 2 Sensor 1) open/short (High voltage)
P032C: Knock sensor (for Bank 1 Sensor 2) open/short (Low voltage)
P032D: Knock sensor (for Bank 1 Sensor 2) open/short (High voltage)
P033C: Knock sensor (for Bank 2 Sensor 2) open/short (Low voltage)
P033D: Knock sensor (for Bank 2 Sensor 2) open/short (High voltage)
Required Sensors/Components (Main) Knock sensor (Bank 1, 2 Sensor 1, 2)
Required Sensors/Components (Related) -
Frequency of Operation Continuous
Duration 1 second
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs are not stored None
Battery voltage 10.5 V or more
Time after engine start 5 seconds or more

TYPICAL MALFUNCTION THRESHOLDS

Knock Sensor Range Check (Low voltage): P0327, P0332, P032C and P033C:
Knock sensor voltage Less than 0.5 V

Knock Sensor Range Check (High voltage): P0328, P0333, P032D and P033D:
Knock sensor voltage More than 4.5 V

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Start the engine and wait 10 seconds.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTC.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0327, P0328, P032C, P032D, P0332, P0333, P033C or P033D.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:

If the judgment result shows INCOMPLETE or N/A, idle the engine for 5 minutes and check the DTC judgment result again.


12.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A179937E03
1.271,0.958 1.375,1.115 0.104,0.156 10 false 1 2.313,0.958 2.417,1.115 0.104,0.156 10 false 2 1.313,1.365 1.49,1.51 0.177,0.146 10 false b1 1.313,1.51 3.583,1.698 2.271,0.188 10 false Knock Sensor (for Bank 1 Sensor 1) 1.271,2.542 1.375,2.698 0.104,0.156 10 false 1 2.313,2.542 2.417,2.698 0.104,0.156 10 false 2 1.313,2.948 1.49,3.094 0.177,0.146 10 false b2 1.313,3.094 3.583,3.281 2.271,0.188 10 false Knock Sensor (for Bank 2 Sensor 1) 1.271,4.365 1.375,4.521 0.104,0.156 10 false 1 2.313,4.365 2.417,4.521 0.104,0.156 10 false 2 1.313,4.781 1.49,4.927 0.177,0.146 10 false b3 1.313,4.917 3.583,5.104 2.271,0.188 10 false Knock Sensor (for Bank 1 Sensor 2) 1.271,5.958 1.375,6.115 0.104,0.156 10 false 1 2.313,5.958 2.417,6.115 0.104,0.156 10 false 2 1.313,6.375 1.49,6.521 0.177,0.146 10 false b4 1.313,6.51 3.583,6.698 2.271,0.188 10 false Knock Sensor (for Bank 2 Sensor 2) 5.49,0.875 5.76,1.031 0.271,0.156 10 false D56 5.552,0.698 5.729,0.854 0.177,0.156 10 false 94 5.844,0.771 6.229,0.927 0.385,0.156 10 false KNK1 5.49,2.063 5.76,2.219 0.271,0.156 10 false D56 5.552,1.865 5.729,2.021 0.177,0.156 10 false 93 5.844,1.958 6.281,2.115 0.438,0.156 10 false EKNK 5.49,3.646 5.76,3.802 0.271,0.156 10 false D56 5.521,3.469 5.771,3.625 0.25,0.156 10 false 116 5.844,3.542 6.229,3.698 0.385,0.156 10 false EKN2 5.49,4.281 5.76,4.438 0.271,0.156 10 false D56 5.552,4.094 5.729,4.25 0.177,0.156 10 false 96 5.844,4.365 6.229,4.521 0.385,0.156 10 false KNK3 5.49,5.875 5.76,6.031 0.271,0.156 10 false D56 5.51,5.688 5.771,5.844 0.26,0.156 10 false 119 5.844,5.958 6.229,6.115 0.385,0.156 10 false KNK4 5.49,5.469 5.76,5.625 0.271,0.156 10 false D56 5.563,5.292 5.75,5.448 0.188,0.156 10 false 95 5.844,5.375 6.229,5.531 0.385,0.156 10 false EKN3 5.49,7.063 5.76,7.219 0.271,0.156 10 false D56 5.521,6.865 5.771,7.021 0.25,0.156 10 false 118 5.844,6.958 6.229,7.115 0.385,0.156 10 false EKN4 5.49,2.458 5.76,2.615 0.271,0.156 10 false D56 5.521,2.271 5.771,2.427 0.25,0.156 10 false 117 5.844,2.542 6.229,2.698 0.385,0.156 10 false KNK2 6.125,7.719 6.458,7.875 0.333,0.156 10 false ECM 4.542,0.677 4.615,0.823 0.073,0.146 10 false * 4.542,2.281 4.615,2.417 0.073,0.135 10 false * 4.542,4.094 4.615,4.229 0.073,0.135 10 false * 4.542,5.688 4.615,5.823 0.073,0.135 10 false * 0.688,8.25 1.406,8.417 0.719,0.167 10 false *: Shielded

CAUTION / NOTICE / HINT

HINT:
·

DTCs P0327 and P0328 are for the bank 1 sensor 1 knock sensor circuit.

·

DTCs P032C and P032D are for the bank 1 sensor 2 knock sensor circuit.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

DTCs P0332 and P0333 are for the bank 2 sensor 1 knock sensor circuit.

·

DTCs P033C and P033D are for the bank 2 sensor 2 knock sensor circuit.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT KNOCK SENSOR
U152966E02
1.042,2.135 0.271,3.219 true 1.125,2.146 1.031,3.24 true 1.219,2.135 1.49,3.229 true 1.302,2.135 2.167,3.198 true 0.24,2.677 1.052,2.042 true 0.708,2.99 1.125,2.052 true 1.74,2.99 1.219,2.042 true 2.229,2.719 1.302,2.052 true 0.24,0.99 0.542,1.167 0.302,0.177 10 false D56 0.052,3.208 0.438,3.375 0.385,0.167 10 false EKN2 0.802,3.229 1.208,3.396 0.406,0.167 10 false KNK2 1.354,3.219 1.75,3.385 0.396,0.167 10 false EKN4 2.042,3.188 2.438,3.354 0.396,0.167 10 false KNK4 0.021,2.677 0.438,2.844 0.417,0.167 10 false EKNK 0.479,2.969 0.885,3.135 0.406,0.167 10 false KNK1 1.542,3 1.938,3.167 0.396,0.167 10 false EKN3 2.094,2.719 2.49,2.885 0.396,0.167 10 false KNK3 0.031,0.042 2.396,0.406 2.365,0.365 10 false Front view of wire harness connector: (to ECM)

a.

Disconnect the D56 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D56-94 (KNK1) - D56-93 (EKNK) 20°C (68°F) 120 to 280 kΩ
D56-117 (KNK2) - D56-116 (EKN2) 20°C (68°F) 120 to 280 kΩ
D56-96 (KNK3) - D56-95 (EKN3) 20°C (68°F) 120 to 280 kΩ
D56-119 (KNK4) - D56-118 (EKN4) 20°C (68°F) 120 to 280 kΩ


Result
Result Proceed to
NG A
OK B



A

2.CHECK HARNESS AND CONNECTOR (ECM - KNOCK SENSOR)

B

3.INSPECT ECM
2.CHECK HARNESS AND CONNECTOR (ECM - KNOCK SENSOR)
a.

Disconnect the D56 ECM connector.


b.

Disconnect the b3, b4, b1 or b2 knock sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
b1-2 - D56-94 (KNK1) Always Below 1 Ω
b1-1 - D56-93 (EKNK) Always Below 1 Ω
b2-2 - D56-117 (KNK2) Always Below 1 Ω
b2-1 - D56-116 (EKN2) Always Below 1 Ω
b3-2 - D56-96 (KNK3) Always Below 1 Ω
b3-1 - D56-95 (EKN3) Always Below 1 Ω
b4-2 - D56-119 (KNK4) Always Below 1 Ω
b4-1 - D56-118 (EKN4) Always Below 1 Ω
b1-2 or D56-94 (KNK1) - Body ground Always 10 kΩ or higher
b1-1 or D56-93 (EKNK) - Body ground Always 10 kΩ or higher
b2-2 or D56-117 (KNK2) - Body ground Always 10 kΩ or higher
b2-1 or D56-116 (EKN2) - Body ground Always 10 kΩ or higher
b3-2 or D56-96 (KNK3) - Body ground Always 10 kΩ or higher
b3-1 or D56-95 (EKN3) - Body ground Always 10 kΩ or higher
b4-2 or D56-119 (KNK4) - Body ground Always 10 kΩ or higher
b4-1 or D56-118 (EKN4) - Body ground Always 10 kΩ or higher


HINT:

Perform "Inspection After Repair" after replacing the knock sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM
a.

Disconnect the b3, b4, b1 or b2 knock sensor connector.


b.
U152967E03
0.125,0.073 2.479,0.417 2.354,0.344 10 false Front view of wire harness connector: (to Knock Sensor) 0.646,1.313 0.854,1.458 0.208,0.146 10 false b1 0.646,1.656 0.854,1.802 0.208,0.146 10 false b2 0.646,1.969 0.854,2.115 0.208,0.146 10 false b3 0.646,2.302 0.854,2.448 0.208,0.146 10 false b4

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
1 - 2 Ignition switch ON 4.5 to 5.5 V




OK

NG