The crankshaft position (CKP) sensor system consists of a crankshaft position sensor plate and Magnetic Resistance Element (MRE) type sensor. The crankshaft position sensor plate has 34 teeth at 10° intervals (2 teeth are missing for detecting top dead center), and is installed to the rear end of the crankshaft. The crankshaft position sensor outputs 34 rotation signals per crankshaft revolution. The ECM uses the G2 signal to distinguish between the cylinders, and uses the NE signal to detect the crankshaft position and engine speed.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0335 | ·
No CKP sensor signal to ECM while cranking (1 trip detection logic) ·
No CKP sensor signal to ECM at engine speed of less than 450 rpm (1 trip detection logic) |
·
Open or short in CKP sensor circuit ·
CKP sensor ·
CKP sensor plate ·
ECM |
| P0337 | Output voltage of CKP sensor 0.3 V or less for 4 seconds (1 trip detection logic) | ·
Open or short in CKP sensor circuit ·
CKP sensor ·
CKP sensor plate ·
ECM |
| P0338 | Output voltage of CKP sensor 4.7 V or more for 4 seconds (1 trip detection logic) | ·
Open or short in CKP sensor circuit ·
CKP sensor ·
CKP sensor plate ·
ECM |
| P0339 | Under conditions (a), (b) and (c), no CKP sensor signal to ECM for 0.05 seconds or more (1 trip detection logic):
(a) Engine speed 1000 rpm or more (b) Starter signal OFF (c) 3 seconds or more have elapsed since starter signal switched from ON to OFF |
·
Open or short in CKP sensor circuit ·
CKP sensor ·
CKP sensor plate ·
ECM |
Reference: Inspection using an oscilloscope.
| Tester Connection | Tool Setting | Condition | Specified Condition |
|---|---|---|---|
| D56-110 (NE+) - D56-111 (NE-) | 5 V/DIV., 20 msec./DIV. | Cranking or idling | The correct waveform is as shown |
| D56-90 (G2) - D56-89 (G2-) | 5 V/DIV., 20 msec./DIV. | Cranking or idling | The correct waveform is as shown |
G2 stands for the camshaft position sensor signal, and NE stands for the crankshaft position sensor signal.
If there is no signal from the crankshaft position sensor despite the crankshaft revolving, the ECM interprets this as a malfunction of the sensor.
When the sensor output voltage remains at less than 0.3 V, or more than 4.7 V for more than 4 seconds, the ECM stores a DTC.
| Related DTCs | P0335: Crankshaft position sensor range check/rationality
P0337: Crankshaft position sensor check (Low voltage) P0338: Crankshaft position sensor check (High voltage) |
| Required sensors/Components (Main) | Crankshaft Position (CKP) sensor |
| Required sensors/Components (Related) | Camshaft position sensor |
| Frequency of operation | Continuous |
| Duration | -: Verify pulse input (case 2)
4.7 seconds: Verify pulse input (case 1) 4 seconds: Others |
| MIL operation | Immediate |
| Sequence of operation | None |
| Monitor runs whenever following DTCs not stored | None |
| Battery voltage | Higher than 6 V |
| CKP sensor voltage | 0.3 to 4.7 V |
| Time after starter off to ON | 0.5 seconds or more |
| Ignition switch | ON |
| Starter | ON |
| Minimum battery voltage while starter ON | Below 11 V |
| Battery voltage | Higher than 6 V |
| CKP sensor voltage | 0.3 to 4.7 V |
| Ignition switch | ON |
| Engine speed (Top dead center) | 450 rpm or higher |
| Engine speed (30°CA) | 450 rpm or higher |
| Starter | OFF |
| Time after starter turned from ON to OFF | 3 seconds or more |
| Battery voltage | 8 V or more |
| Ignition switch | ON |
| Starter | OFF |
| Engine speed signal | No signal |
| CKP sensor voltage | Less than 0.3 V |
| CKP sensor voltage | More than 4.7 V |
| CKP sensor | ·
CKP sensor output voltage fluctuates while engine crankshaft revolving ·
34 CKP sensor signals per crankshaft revolution |
| CKP sensor voltage | 0.3 to 4.7 V |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Start the engine.
Idle the engine for 20 seconds or more [A].
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
Read the pending DTC.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0335, P0337 or P0338.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.
If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.
The engine speed can be checked by using the Techstream. To check, follow the procedures below:
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.
The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position (CKP) sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed, if the CKP sensor output voltage is insufficient.
Read freeze frame data using the Techstream. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.
Start the engine.
Read the values displayed on the Techstream while the engine is running.
Correct values are displayed.
To check the engine speed change, display the graph on the Techstream.
If the engine does not start, check the engine speed while cranking.
If the engine speed indicated on the Techstream remains zero (0), there may be an open or short in the Crankshaft Position (CKP) sensor circuit.
OK
NG
Disconnect the D1 crankshaft position sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| D1-3 (VC) - Body ground | Ignition switch ON | 4.5 to 5.0 V |
OK
NG
Disconnect the D1 crankshaft position sensor connector.
Disconnect the D56 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D1-1 (NE+) - D56-110 (NE+) | Always | Below 1 Ω |
| D1-2 (NE-) - D56-111 (NE-) | Always | Below 1 Ω |
| D1-1 (NE+) or D56-110 (NE+) - Body ground | Always | 10 kΩ or higher |
| D1-2 (NE-) or D56-111 (NE-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Check the crankshaft position sensor installation.
Sensor is installed correctly.
OK
NG
Check the teeth of the sensor plate.
Sensor plate does not have any cracks or deformation.
OK
NG
Replace the crankshaft position sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>REMOVAL).
NEXT
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Refer to the confirmation driving pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Display (DTC Output) | Proceed to |
|---|---|
| No output | A |
| P0335, P0337, P0338 and/or P0339 | B |
If the engine does not start, replace the ECM.
A
B
Disconnect the D1 crankshaft position sensor connector.
Disconnect the D56 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D1-3 (VC) - D56-66 (VCV2) | Always | Below 1 Ω |
OK
NG