Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM
RM27L0U _51 Engine / Hybrid System _049293 3UR-FBE ENGINE CONTROL _0235531 SFI SYSTEM C

3UR-FBE ENGINE CONTROL  SFI SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, the positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.

DTC No. DTC Detection Condition Trouble Area
P0617 When conditions (a), (b) and (c) met, positive (+B) battery voltage 10.5 V or more applied to ECM for 20 seconds (1 trip detection logic)

(a) Vehicle speed 20 km/h (12.4 mph) or more

(b) Engine speed 1000 rpm or more

(c) STA signal ON


·

Park/Neutral Position (PNP) switch assembly

·

ST relay circuit

·

Ignition switch

·

ECM



MONITOR STRATEGY

Related DTCs P0617: Starter signal
Required Sensors/Components (Main) ST relay, PNP switch and Ignition switch
Required Sensors/Components (Related) Vehicle Speed Sensor (VSS), Crankshaft Position (CKP) sensor
Frequency of Operation Continuous
Duration 20 seconds
MIL Operation Immediate
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs not stored None
Battery voltage 10.5 V or more
Vehicle speed 20 km/h (12.43 mph) or more
Engine speed 1000 rpm or more

TYPICAL MALFUNCTION THRESHOLDS

Starter signal ON

CONFIRMATION DRIVING PATTERN

A199310E01
1.226,1.979 1.604,2.156 0.378,0.177 10 Idling 0.456,2.238 1.653,2.408 1.198,0.170 10 Ignition Switch ON 0.435,0.603 1.559,0.783 1.125,0.180 10 24 km/h (15 mph) 2.393,2.851 3.076,3.167 0.684,0.316 10 5 seconds or more 3.427,2.938 4.699,3.103 1.272,0.165 10 20 seconds or more 2.004,2.336 2.197,2.525 0.193,0.188 10 [A] 2.586,2.125 2.796,2.297 0.210,0.172 10 [B] 3.02,3.309 3.259,3.492 0.239,0.184 10 [C] 4.03,0.457 4.257,0.625 0.227,0.168 10 [D] 4.905,3.342 5.139,3.510 0.234,0.168 10 [E]

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Idle the engine for 5 seconds or more [B].

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

8.

Read the pending DTC.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0617.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].



12.

Drive the vehicle at 24 km/h (15 mph) or more for 20 seconds or more [D].

13.

Check the DTC judgment result [E].

14.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A243747E01
5.953,1.235 6.322,1.400 0.369,0.165 10 NSW 5.953,0.849 6.358,1.015 0.405,0.165 10 STAR 5.953,0.373 6.419,0.538 0.466,0.165 10 STSW 5.953,1.718 6.322,1.883 0.369,0.165 10 STA 5.612,1.633 5.886,1.793 0.274,0.160 10 A27 5.612,1.234 5.886,1.394 0.274,0.160 10 D56 5.612,0.842 5.886,1.002 0.274,0.160 10 D56 5.612,0.377 5.886,0.537 0.274,0.160 10 A27 5.616,1.077 5.883,1.226 0.267,0.149 10 120 5.651,1.472 5.835,1.622 0.184,0.151 10 46 5.651,0.205 5.835,0.355 0.184,0.151 10 14 5.651,0.667 5.835,0.818 0.184,0.151 10 16 4.912,1.55 5.020,1.699 0.107,0.149 10 5 4.163,1.55 4.270,1.699 0.107,0.149 10 4 4.18,1.919 4.475,2.075 0.295,0.156 10 D21 4.18,2.041 5.160,2.386 0.980,0.345 10 Park/Neutral Position Switch 2.42,1.861 2.707,2.017 0.288,0.156 10 A41 2.42,1.994 2.808,2.146 0.389,0.152 10 Diode 1.858,1.546 1.972,1.695 0.114,0.149 10 7 0.604,1.546 0.718,1.695 0.114,0.149 10 5 1.528,1.721 1.813,1.874 0.284,0.152 10 ST2 1.213,3.585 1.446,3.737 0.232,0.152 10 ST 3.329,3.276 3.561,3.429 0.232,0.152 10 ST 0.744,1.721 1.066,1.874 0.323,0.152 10 AM2 0.46,2.846 0.783,2.998 0.323,0.152 10 AM2 3.742,2.501 3.849,2.650 0.107,0.149 10 3 3.009,2.501 3.116,2.650 0.107,0.149 10 5 3.002,2.889 3.109,3.038 0.107,0.149 10 2 3.74,2.889 3.847,3.038 0.107,0.149 10 1 4.183,5.287 4.298,5.443 0.114,0.156 10 1 3.651,5.315 3.765,5.471 0.114,0.156 10 1 3.913,5.287 4.125,5.436 0.211,0.149 10 E7 3.611,5.476 3.823,5.625 0.211,0.149 10 E8 3.707,5.924 4.169,6.080 0.461,0.156 10 Starter 6.31,4.681 6.653,4.837 0.343,0.156 10 ECM 1.388,6.044 1.871,6.213 0.482,0.170 10 Battery 0.799,2.339 1.733,2.495 0.934,0.156 10 Ignition Switch 0.799,2.2 1.083,2.370 0.284,0.170 10 H10 4.307,1.545 4.458,1.696 0.151,0.151 10 B 4.76,1.549 4.894,1.700 0.134,0.151 10 L

CAUTION / NOTICE / HINT

HINT:
·

The following troubleshooting flowchart is based on the premise that the engine is cranked normally.

If the engine will not crank, proceed to the problem symptoms table (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>PROBLEM SYMPTOMS TABLE).

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.


d.

Check the value displayed on the Techstream when the ignition switch is turned to the ON and START positions.

OK:
Ignition Switch Position Starter Signal
ON OFF
START ON




OK

NG

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
C160109E32
2.354,2.406 2,1.917 false 1.625,2.385 1.719,1.896 false 1.958,2.406 1.865,1.917 false 1.625,1.677 1.542,1.188 false 1.083,2.385 1.438,1.896 false 1.813,1.677 2.177,1.188 false 1.385,1.677 1.021,1.188 false 0.052,0 2.635,0.365 2.583,0.365 10 false Component without harness connected: (Park / Neutral Position Switch) 1.396,0.969 1.677,1.156 0.281,0.188 10 false RB 0.896,1.042 1.042,1.219 0.146,0.177 10 false B 1.906,2.417 2.167,2.594 0.26,0.177 10 false PL 2.385,2.375 2.594,2.552 0.208,0.177 10 false L 1.5,2.396 1.781,2.594 0.281,0.198 10 false DL 0.885,2.375 1.125,2.563 0.24,0.188 10 false NL 2.208,1.042 2.417,1.219 0.208,0.177 10 false RL

a.

Disconnect the D21 park/neutral position switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
4 (B) - 5 (L) Shift lever position P Below 1 Ω
Shift lever position N Below 1 Ω
Shift lever position not on P or N 10 kΩ or higher
2 (RB) - 5 (L) All positions 10 kΩ or higher


Result
Result Proceed to
NG A
OK B



A

3.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

B

5.INSPECT IGNITION SWITCH ASSEMBLY
3.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Replace the park/neutral position switch assembly (See page Drivetrain>AB60F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL).



NEXT

4.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
4.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.


d.

Check the value displayed on the Techstream when the ignition switch is turned to the ON and START positions.

OK:
Ignition Switch Position Starter Signal
ON OFF
START ON




OK

SYSTEM OK

NG

5.INSPECT IGNITION SWITCH ASSEMBLY
5.INSPECT IGNITION SWITCH ASSEMBLY
B110407E17
2.771,1.167 2.104,1.865 true 2.073,1.177 1.75,1.813 true 1.063,1.854 0.656,1.188 true 1.802,2.188 2.219,2.823 true 2.104,2.156 2.615,2.844 true 1.385,2.188 0.927,2.708 true 0.073,0.104 2.594,0.479 2.521,0.375 10 false Component without harness connected: (Ignition Switch) 2.823,1.073 3.073,1.229 0.25,0.156 10 false IG1 2.052,1.031 2.365,1.188 0.313,0.156 10 false ACC 0.344,1.063 0.667,1.229 0.323,0.167 10 false AM1 0.781,2.719 1.083,2.875 0.302,0.156 10 false ST2 2.656,2.771 2.99,2.938 0.333,0.167 10 false AM2 2.125,2.854 2.396,3.021 0.271,0.167 10 false IG2

a.

Disconnect the H10 ignition switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Switch Condition Specified Condition
5 (AM2) - 7 (ST2) Ignition switch position LOCK 10 kΩ or higher
Ignition switch position START Below 1 Ω


Result
Result Proceed to
NG A
OK B



A

6.REPLACE IGNITION SWITCH ASSEMBLY

B

8.REPAIR OR REPLACE HARNESS OR CONNECTOR (PNP SWITCH - STA TERMINAL OF ECM)
6.REPLACE IGNITION SWITCH ASSEMBLY
a.

Replace the ignition switch assembly (See page Engine / Hybrid System>3UR-FBE STARTING>IGNITION SWITCH>REMOVAL).



NEXT

7.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
7.READ VALUE USING TECHSTREAM (STARTER SIGNAL)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.


d.

Check the value displayed on the Techstream when the ignition switch is turned to the ON and START positions.

OK:
Ignition Switch Position Starter Signal
ON OFF
START ON




OK

SYSTEM OK

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR (PNP SWITCH - STA TERMINAL OF ECM)
8.REPAIR OR REPLACE HARNESS OR CONNECTOR (PNP SWITCH - STA TERMINAL OF ECM)

NEXT

9.CHECK WHETHER DTC OUTPUT RECURS
9.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read DTCs.

Result
Result Proceed to
P0617 is output A
No DTC is output B



A

B

SYSTEM OK