The fuel trim is related to the feedback compensation value, not to the basic injection time. The fuel trim consists of both the short-term and the long-term fuel trims.
The short-term fuel trim is fuel compensation that is used to constantly maintain the air-fuel ratio at stoichiometric levels. The signal from the Air-Fuel Ratio (A/F) sensor indicates whether the air-fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air-fuel ratio is rich and an increase in the fuel injection volume if it is lean.
Factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short-term fuel trim compensation.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0171
P0174 |
With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side
(2 trip detection logic) |
·
Air induction system ·
Injector blockage ·
Mass Air Flow (MAF) meter ·
Engine Coolant Temperature (ECT) sensor ·
Fuel pressure ·
Gas leakage from exhaust system ·
Open or short in A/F sensor (for Sensor 1) circuit ·
A/F sensor (for Sensor 1) ·
A/F sensor heater (for Sensor 1) ·
Integration relay ·
A/F sensor heater and integration relay circuits ·
PCV valve and hose ·
PCV hose connections ·
ECM ·
Fuel pressure switching valve ·
Fuel pressure regulator ·
Fuel pressure regulator for high pressure ·
Fuel pump ·
Fuel pump ECU ·
Fuel sender gauge assembly ·
Wire harness or connector |
| P0172
P0175 |
With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side
(2 trip detection logic) |
·
Injector leakage or blockage ·
MAF meter ·
ECT sensor ·
Ignition system ·
Fuel pressure ·
Gas leakage from exhaust system ·
Open or short in A/F sensor (for Sensor 1) circuit ·
A/F sensor (for Sensor 1) ·
A/F sensor heater (for Sensor 1) ·
Integration relay ·
A/F sensor heater and integration relay circuits ·
ECM ·
Fuel pressure switching valve ·
Fuel pressure regulator ·
Fuel pressure regulator for high pressure ·
Fuel pump ·
Fuel pump ECU ·
Fuel sender gauge assembly ·
Wire harness or connector |
When DTC P0171 or P0174 is set, the actual air-fuel ratio is on the lean side. When DTC P0172 or P0175 is set, the actual air-fuel ratio is on the rich side.
If the vehicle runs out of fuel, the air-fuel ratio is lean and DTC P0171 or P0174 may be set. The MIL is then illuminated.
When the total of the short-term and long-term fuel trim values is within the malfunction threshold (and the engine coolant temperature is more than 75°C [167°F]), the system is functioning normally.
Under closed-loop fuel control, fuel injection volumes that deviate from those estimated by the ECM cause changes in the long-term fuel trim compensation value. The long-term fuel trim is adjusted when there are persistent deviations in the short-term fuel trim values. Deviations from the ECM's estimated fuel injection volumes also affect the average fuel trim learning value, which is a combination of the average short-term fuel trim (fuel feedback compensation value) and the average long-term fuel trim (learning value of the air-fuel ratio). If the average fuel trim learning value exceeds the malfunction threshold, the ECM interprets this as a fault in the fuel system and stores a DTC.
Example:
The average fuel trim learning value is +35% or more or -35% or less, the ECM interprets this as a fuel system malfunction.
| Related DTCs | P0171: Fuel trim lean (for Bank 1)
P0172: Fuel trim rich (for Bank 1) P0174: Fuel trim lean (for Bank 2) P0175: Fuel trim rich (for Bank 2) |
| Required Sensors/Components (Main) | Fuel system |
| Required Sensors/Components (Related) | A/F sensor, Mass air flow meter, Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Duration | Within 10 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | P0010, P0020 (Camshaft timing oil control valve)
P0011, P0021 (VVT System - Advance) P0012, P0022 (VVT System - Retard) P0013, P0023 (Exhaust camshaft timing oil control valve) P0014, P0024 (Exhaust VVT System - Advance) P0015, P0025 (Exhaust VVT System - Retard) P0016, P0018 (VVT System - Misalignment) P0017, P0019 (Exhaust VVT System - Misalignment) P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater) P0102, P0103 (Mass air flow meter) P0115, P0117, P0118 (Engine coolant temperature sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0335 (Crankshaft position sensor) P1340 (Camshaft position sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P0351 - P0358 (Igniter) P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor) P0412, P0415, P0418, P0419, P1613, P1614 (Secondary air injection system control) P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2, P21A3 (Air-fuel ratio imbalance) P2440 - P2447 (Secondary air injection system) P0500 (Vehicle speed sensor) |
| Fuel system status | Closed loop |
| Battery voltage | 11 V or more |
| Either of following conditions 1 or 2 met | - |
| 1. Engine speed | Below 1100 rpm |
| 2. Engine load | 10% or more |
| Catalyst monitor | Not executed |
| Ethanol content learning | Not executed |
| Refuel with small amount or on an incline | Not executed |
| Purge-cut | Executing |
| Either of following conditions 1 or 2 met | - |
| 1. Average of short-term fuel trim and long-term fuel trim | 35% or more (varies with ECT) |
| 2. Average of short-term fuel trim and long-term fuel trim | -35% or less (varies with ECT) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on [A].
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or more with all the accessories switched OFF [B].
With the engine warmed up, idle the engine for 2 minutes or more [C].
Drive the vehicle at a speed between 60 km/h and 120 km/h (38 mph and 75 mph) and at an engine speed of between 1400 rpm and 3200 rpm for 5 minutes or more [D].
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
Read the Pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0171, P0172, P0174 or P0175.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit |
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [C] through [E] again.
If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.
A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.
Bank 2 refers to the bank that does not include the No. 1 cylinder.
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
|---|---|
| P0171, P0172, P0174 or P0175 is output | A |
| P0171, P0172, P0174 or P0175 and other DTCs are output | B |
If any DTCs other than P0171, P0172, P0174 or P0175 are output, troubleshoot those DTCs first.
A
B
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Make sure that the Data List item "Alcohol Density Learning" is "Compl".
Enter the following menus: Powertrain / Engine and ECT / Data List / Alcohol Density Estimate, Short FT and Long FT.
Check the data list values, and then write them down.
NEXT
Confirm the alcohol concentration in the fuel (See page Engine / Hybrid System>3UR-FBE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).
Write down the alcohol concentration in the fuel.
NEXT
Use the following formula to calculate the difference between the learned values from step *1 and the actual alcohol concentration in the fuel from step *2.
[ ((Alcohol Density Estimate / 2) + Short FT + Long FT) - (Alcohol Concentration in Fuel / 2) ] < 35%
| Result | Proceed to |
|---|---|
| Difference is 35% or more | A |
| Difference is less than 35% | B |
A
B
Check the fuel injection system (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>Fuel Injection System).
If the problem area cannot be determined by checking the fuel injection system, proceed to the next step.
NEXT
Use the following formula to calculate the difference between the learned value from step *1 and the actual alcohol concentration in the fuel from step *2.
[ (Alcohol Density Estimate / 2) - (Alcohol Concentration in Fuel / 2) ] < 10%
| Result | Proceed to |
|---|---|
| Difference is 10% or more | A |
| Difference is less than 10% | B |
A
B
Confirm the actual alcohol concentration in the fuel from step *2.
| Result | Proceed to |
|---|---|
| Alcohol concentration is 20% or less | A |
| Alcohol concentration is more than 20% | B |
A
B
Replace the fuel with E0 gasoline (replace approximately 20 liters (5 gallons) of fuel).
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Fuel Density Learning Value Reset.
Confirm the following conditions as instructed on the screen.
Ignition switch: ON
Engine: stopped
Battery voltage: 9 V or higher
After confirming, select "Next" and initialize the learned value.
If a message indicating learned value initialization failure is displayed on the screen, confirm the execution conditions, and perform learned value initialization again.
Turn the ignition switch off and wait for at least 30 seconds.
Proceed to the next step without starting the engine after performing "Learning Value Reset".
NEXT
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Fuel Density Learning Value Reset.
Confirm the following conditions as instructed on the screen.
Ignition switch: ON
Engine: stopped
Battery voltage: 9 V or higher
After confirming, select "Next" and initialize the learned value.
If a message indicating learned value initialization failure is displayed on the screen, confirm the execution conditions, and perform learned value initialization again.
Turn the ignition switch off and wait for at least 30 seconds.
Add at least 8 liters (2 gallons) of fuel.
Check "Fuel Remaining Volume" in the Data List and if it has a value of 85% or more, remove enough fuel so that the value decreases to less than 85% before adding fuel.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Alcohol Density learning.
Make sure that the Data List item "Alcohol Density Learning" is "Incmpl".
NEXT
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Fuel Density Learning Value Reset.
After clearing the learned value, the engine may become difficult to start if the concentration of alcohol in the fuel is high. Therefore, it may be necessary to crank the engine a few times before it starts.
If "Fuel Density Learning Value Reset" is performed after warming the engine coolant up to approximately 50°C (122°F), the engine becomes easier to start afterward.
Confirm the following conditions as instructed on the screen.
Ignition switch: ON
Engine: stopped
Battery voltage: 9 V or higher
Press "Next".
When "Next" is pressed, initialization is performed automatically.
Turn the ignition switch off.
Add at least 8 liters (2 gallons) of fuel.
Add fuel immediately after resetting. (Do not start the engine before adding fuel.)
Learning of the alcohol concentration will not be started until the ECM judges that the fuel gauge has moved after resetting. Add at least 8 liters (2 gallons) of fuel.
Check "Fuel Remaining Volume" in the Data List and if it has a value of 85% or more, remove enough fuel so that the value decreases to less than 85% before adding fuel.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Alcohol Density learning.
Make sure that the Data List item "Alcohol Density Learning" is "Incmpl".
NEXT
If the difference between the learned value of the vehicle from step *1 and the actual alcohol concentration in the fuel from step *2 is less than 10%, it is not necessary to perform learning.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Make sure that the Data List item "Alcohol Density Learning" is "Compl".
Enter the following menus: Powertrain / Engine and ECT / Data List / Alcohol Density Estimate, Short FT and Long FT.
Check the data list values, and then write them down.
Confirm the alcohol concentration in the fuel (See page Engine / Hybrid System>3UR-FBE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).
Write down the alcohol concentration in the fuel.
Use the following formula to calculate the difference between the current learned value and the actual alcohol concentration in the fuel.
[ (Alcohol Density Estimate / 2) - (Alcohol Concentration in Fuel / 2) ] < 10%
| Result | Specified Condition |
|---|---|
| Difference between actual alcohol concentration and Alcohol Density Estimate | Less than 10% |
| Short FT and Long FT | Between -35% and 35% |
OK
NG