| DTC | Monitoring Item | Malfunction Detection Condition | Trouble Area | Detection Timing | Detection Logic |
|---|---|---|---|---|---|
| P2610 | Soak timer (built into ECM) | ECM internal malfunction | ECM | Engine running | 2 trip |
The soak timer operates after the ignition switch is turned off. When a certain amount of time has elapsed after turning the ignition switch off, the soak timer activates the ECM to perform malfunction checks which can only be performed after the engine is stopped. The soak timer is built into the ECM.
While the ignition switch is turned off, the ECM monitors the synchronization of the soak timer and CPU clock. If these two are not synchronized, the ECM interprets this as a malfunction, illuminates the MIL and stores the DTC.
If the soak timer activates the ECM even though only a short amount of time has elapsed since the ignition switch was turned off, or if the soak timer does not activate the ECM even though a considerable amount of time has elapsed since the ignition switch was turned off, the ECM determines that the soak timer is malfunctioning, illuminates the MIL and stores a DTC the next time the ignition switch is turned to ON.
| Required Sensors/Components | ECM |
| Frequency of Operation | Once per driving cycle |
| Duration | 2 times: Case 1
-: Case 2 and 3 |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs are not stored | None |
| All of the following conditions are met | - |
| Battery voltage | 8 V or higher |
| Ignition switch | OFF |
| CPU clock elapsed time | 1.96608 seconds or more |
| All of the following conditions are met | - |
| Internal engine off timer (elapsed time from engine stop) | Less than 1800 seconds |
| Battery voltage | 8 V or higher |
| Ignition switch | ON |
| Starter | OFF |
| All of the following conditions are met | - |
| Internal engine off timer (elapsed time from engine stop) | 2400 seconds or more |
| Battery voltage | 8 V or higher |
| Ignition switch | ON |
| Starter | OFF |
| One of the following conditions is met | Condition A, B or C |
| A. Both of the following conditions are met | Condition (a) and (b) |
| (a) CPU clock elapsed time | 1.96608 seconds or more, and less than 8.323072 seconds |
| (b) Internal Engine off timer | 9.375 seconds or more |
| B. Both of the following conditions are met | Condition (c) and (d) |
| (c) CPU clock elapsed time | 8.323072 to 10.420224 seconds |
| (d) Internal Engine off timer | 18.75 seconds or more |
| C. Both of the following conditions are met | Condition (e) and (f) |
| (e) CPU clock elapsed time | More than 10.420224 seconds |
| (f) Internal Engine off timer | Less than 9.375 seconds |
| ECM had the started record | Yes |
| ECM had the started record | No |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Start the engine.
Idle the engine for 10 minutes or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the pending DTC.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2610.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows ABNORMAL, the system has a malfunction.
If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
DTC P2610 is stored if an internal ECM problem is detected. Diagnostic procedures are not required. ECM replacement is necessary.
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Replace the ECM (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>ECM>REMOVAL).
NEXT
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
If no pending DTC is displayed, the repair has been successfully completed.
NEXT