Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM
RM27L0U _51 Engine / Hybrid System _049293 3UR-FBE ENGINE CONTROL _0235531 SFI SYSTEM C

3UR-FBE ENGINE CONTROL  SFI SYSTEM  P0013  Camshaft Position "B" Actuator Circuit / Open (Bank 1)  P0023  Camshaft Position "B" Actuator Circuit / Open (Bank 2)  


DESCRIPTION

This DTC is designed to detect opens or shorts in the Camshaft Timing Oil Control Valve Assembly (OCV) circuit. If the OCV's duty-cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and set the DTC.

The VVT (variable valve timing) system adjusts the exhaust valve timing to improve the driveability. The engine oil pressure turns the camshaft actuator to adjust the valve timing. The OCV is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 volts to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.

A192077E40
4.651,0.815 6.372,1.026 1.721,0.211 10 VVT Sensor (CMP Sensor) 4.651,1.325 5.477,1.485 0.825,0.161 10 CKP Sensor 0.068,0.015 1.618,0.267 1.550,0.253 10 VVT System: 2.333,1.96 3.609,2.134 1.277,0.174 10 Target Valve Timing 2.333,1.287 3.609,1.462 1.277,0.174 10 Actual Valve Timing 2.683,2.695 3.397,2.870 0.714,0.174 10 Correction 2.822,3.204 3.223,3.378 0.402,0.174 10 ECM 1.599,3.747 5.279,3.922 3.681,0.174 10 Camshaft Timing Oil Control Valve Assembly 0.166,2.69 0.860,2.864 0.695,0.174 10 Duty-cycle 4.651,1.827 5.490,1.981 0.839,0.154 10 MAF Meter 4.651,2.854 5.449,3.042 0.797,0.188 10 ECT Sensor 4.651,2.344 5.018,2.511 0.367,0.167 10 TPS 4.651,3.353 5.004,3.506 0.353,0.154 10 VSS 0.313,4.269 1.682,4.474 1.369,0.205 10 Engine Oil Pressure 3.659,4.217 4.885,4.400 1.225,0.184 10 Camshaft Actuator 3.883,4.917 5.049,5.101 1.166,0.184 10 Exhaust Camshaft 2.562,4.571 2.842,4.275 2.842,4.275 3.607,4.275 false 3.177,4.781 3.32,5.008 3.32,5.008 3.852,5.008 false

DTC No. DTC Detection Condition Trouble Area
P0013 Open or short in OCV (for exhaust side of bank 1) circuit
(1 trip detection logic)
·

Open or short in OCV (for exhaust side of bank 1) circuit

·

OCV (for exhaust side of bank 1)

·

ECM


P0023 Open or short in OCV (for exhaust side of bank 2) circuit
(1 trip detection logic)
·

Open or short in OCV (for exhaust side of bank 2) circuit

·

OCV (for exhaust side of bank 2)

·

ECM



MONITOR DESCRIPTION

This DTC is designed to detect opens or shorts in the Camshaft Timing Oil Control Valve Assembly (OCV) circuit. If the OCV's duty-cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and set the DTC.

MONITOR STRATEGY

Related DTCs P0013: Exhaust camshaft OCV (for Bank 1)
P0023: Exhaust camshaft OCV (for Bank 2)
Required sensors/Components (Main) Camshaft timing oil control valve (for exhaust side)
Required sensors/Components (Related) -
Frequency of operation Continuous
Duration 1 second
MIL operation Immediate
Sequence of operation None

TYPICAL ENABLING CONDITIONS

All
Monitor runs whenever following DTCs not stored None
All of following conditions met -
Starter OFF
Ignition switch ON
Time after ignition switch off to ON 0.5 seconds or more

Case 1
One of following conditions met -
A. All of following conditions met -
Battery voltage 11 to 13 V
Target duty cycle Less than 70%
B. All of following conditions met -
Battery voltage 13 V or more
Target duty cycle Less than 80%

Case 2
Current cut status Not cut

TYPICAL MALFUNCTION THRESHOLDS

Case 1
Output duty cycle 100% or more

Case 2
Output duty cycle 3% or less

COMPONENT OPERATING RANGE

OCV duty-cycle 3 to 100% when engine running

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Wait 5 seconds.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read Pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0013 or P0023.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



12.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A178641E20
5.854,4.115 6.208,4.302 0.354,0.188 10 false ECM 5.406,0.49 5.844,0.646 0.438,0.156 10 false OE1+ 5.406,1.219 5.844,1.375 0.438,0.156 10 false OE1- 5.406,2.469 5.844,2.625 0.438,0.156 10 false OE2+ 5.406,3.198 5.844,3.354 0.438,0.156 10 false OE2- 0.094,1.667 2.177,1.865 2.083,0.198 10 false OCV (for Exhaust side of Bank 1) 0.094,3.646 2.229,3.906 2.135,0.26 10 false OCV (for Exhaust Side of Bank 2) 0.094,1.469 0.375,1.635 0.281,0.167 10 false D28 0.094,3.448 0.375,3.615 0.281,0.167 10 false D29 1.458,0.479 1.583,0.667 0.125,0.188 10 false 1 1.458,1.219 1.573,1.396 0.115,0.177 10 false 2 1.458,2.427 1.583,2.615 0.125,0.188 10 false 1 1.458,3.167 1.573,3.344 0.115,0.177 10 false 2 5.115,3.125 5.292,3.281 0.177,0.156 10 false 49 5.115,2.385 5.292,2.542 0.177,0.156 10 false 50 5.115,1.156 5.292,1.313 0.177,0.156 10 false 55 5.115,0.417 5.292,0.573 0.177,0.156 10 false 56 5.073,0.615 5.375,0.76 0.302,0.146 10 false D56 5.073,1.354 5.375,1.5 0.302,0.146 10 false D56 5.063,2.573 5.365,2.719 0.302,0.146 10 false D56 5.073,3.313 5.375,3.458 0.302,0.146 10 false D56

CAUTION / NOTICE / HINT

HINT:
·

If DTC P0013 is displayed, check the bank 1 VVT system for exhaust camshaft circuit.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

If DTC P0023 is displayed, check the bank 2 VVT system for exhaust camshaft circuit.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.



PROCEDURE

1.CHECK DTC (DTC P0013 OR P0023)
a.

Connect the Techstream to the DLC3.


b.

Clear DTC after recording the freeze frame data and DTC.


c.

Turn the ignition switch off.


d.

Allow the engine to idle and check DTC.


e.

Check that P0013 or P0023 is not output.

OK:

P0013 or P0023 is not output.




OK

NG

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
a.

Disconnect the D28 or D29 camshaft timing oil control valve assembly connector.


b.

Disconnect the D56 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D28-1 - D56-56 (OE1+) Always Below 1 Ω
D28-2 - D56-55 (OE1-) Always Below 1 Ω
D29-1 - D56-50 (OE2+) Always Below 1 Ω
D29-2 - D56-49 (OE2-) Always Below 1 Ω
D28-1 or D56-56 (OE1+) - Body ground Always 10 kΩ or higher
D28-2 or D56-55 (OE1-) - Body ground Always 10 kΩ or higher
D29-1 or D56-50 (OE2+) - Body ground Always 10 kΩ or higher
D29-2 or D56-49 (OE2-) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR