Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM
RM27L0U _51 Engine / Hybrid System _049293 3UR-FBE ENGINE CONTROL _0235531 SFI SYSTEM C

3UR-FBE ENGINE CONTROL  SFI SYSTEM  P011B  Engine Coolant Temperature / Intake Air Temperature Correlation  


DESCRIPTION

The engine has two temperature sensors, an Engine Coolant Temperature (ECT) sensor and an Intake Air Temperature (IAT) sensor, to detect the temperature while the engine is in operation. A thermistor, whose resistance value varies according to the temperature, is built into each sensor. When the temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes. Based on these temperature signals output from the sensors, the ECM determines the fuel injection time and the ignition timing to control the engine.

DTC Code DTC Detection Condition Trouble Area
P011B

All of the following conditions are met (2 trip detection logic):

1.

The battery voltage is 10.5 V or higher.

2.

7 hours or more have elapsed from engine stop on the previous trip.

3.

102 seconds after a cold engine start.

4.

The minimum Intake Air Temperature (IAT) after the engine starts is higher than -10°C (14°F).

5.

The average Engine Coolant Temperature (ECT) before the engine starts is higher than -10°C (14°F).

6.

The difference between the readings of ECT and IAT is higher than 25°C (45°F).



·

IAT sensor

·

ECT sensor

·

ECM



A379985E01
3.417,1.656 3.573,1.073 3.573,1.073 3.792,1.073 false 0.313,0.188 3.313,0.583 3,0.396 10 false Difference Between Engine Coolant Temperature and Intake Air Temperature 0.521,0.979 1.052,1.156 0.531,0.177 10 false °C (°F) 0.354,1.521 0.875,1.719 0.521,0.198 10 false 40 (72) 0.344,2.333 0.865,2.531 0.521,0.198 10 false 20 (36) 0.219,3.156 0.594,3.344 0.375,0.188 10 false 0 (0) 0.281,3.76 0.854,3.979 0.573,0.219 10 false -20 (-36) 0.385,5.188 1.677,5.385 1.292,0.198 10 false Ignition Switch OFF 2.917,5.167 3.792,5.344 0.875,0.177 10 false Engine Start 4.135,4.323 4.469,4.5 0.333,0.177 10 false Fail 4.115,1.719 4.448,1.896 0.333,0.177 10 false Fail 3.844,0.979 4.75,1.177 0.906,0.198 10 false 102 Seconds 4.99,2.344 5.896,2.542 0.906,0.198 10 false 25°C (45°F) 5.01,3.792 5.938,3.99 0.927,0.198 10 false -25°C (-45°F) 6.5,4.917 7.094,5.104 0.594,0.188 10 false Time (h) 1.938,4.875 2.094,5.042 0.156,0.167 10 false 5 2.292,4.875 2.448,5.042 0.156,0.167 10 false 7

HINT:
·

Waiting is required to prevent the temperature of the engine from affecting the readings. If the engine has been operated recently, it will not be possible to accurately compare the readings.


·

For diagnosis, in order to duplicate the detection conditions of the DTC, it is necessary to park the vehicle for 7 hours. Parking the vehicle for 7 hours ensures that the actual temperature of the ECT and IAT are very similar. When the vehicle has been parked for less than 7 hours, differences in the readings may exist. However, this does not necessarily indicate a fault.



MONITOR DESCRIPTION

The ECM monitors the difference between the Engine Coolant Temperature (ECT) and the Intake Air Temperature (IAT) when the engine is started cold to detect the engine temperature conditions accurately. The monitor runs when the engine started cold after 7 hours or more have elapsed since the engine was stopped (ignition switch turned off) on the previous trip. If the difference between the ECT and the IAT on a cold start exceeds 25°C (45°F), the ECM interprets this as a malfunction in the ECT sensor circuit and IAT sensor circuit, and stores the DTC.

MONITOR STRATEGY

Related DTCs P011B: Engine Coolant Temperature (ECT) / Intake Air Temperature (IAT) sensor correlation
Required Sensors/Components (Main) ECT / IAT sensor
Required Sensors/Components (Related) -
Frequency of Operation Once per driving cycle
Duration -
MIL Operation 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

The monitor will run whenever these DTCs are not stored None
All of following conditions met -
(a) Soak Time 7 hours or more
(b) Battery voltage 10.5 V or higher
(c) Time after engine start 102 seconds or more
Either of the following conditions are met Condition (a) and (b)
(a) Minimum IAT after engine start -10°C (14°F) or higher
(b) ECT before engine start -10°C (14°F) or higher
Mass air flow meter circuit failure (P0102, P0103) Not detected
Intake air temperature sensor circuit failure (P0112, P0113) Not detected
Engine coolant temperature circuit failure (P0115, P0117, P0118, P0125) Not detected
Soak timer circuit failure (P2610) Not detected

TYPICAL MALFUNCTION THRESHOLDS

Deviated temperature (difference between ECT and IAT) Below -25°C (-45°F) or higher than 25°C (45°F)

CONFIRMATION DRIVING PATTERN

A213993E01
0.987,1.211 1.402,1.413 0.415,0.202 10 Idling 0.239,2.257 1.395,2.413 1.156,0.156 10 Ignition Switch off 2.079,1.623 2.297,1.842 0.218,0.218 10 [A] 3.385,2.11 3.583,2.306 0.198,0.196 10 [B] 5.224,1.077 5.439,1.278 0.215,0.201 10 [C] 6.166,2.867 6.386,3.055 0.220,0.189 10 [D] 4.723,2.579 6.004,2.756 1.281,0.177 10 60 seconds or more 2.947,2.516 4.068,2.679 1.121,0.163 10 7.5 hours or more 0.239,1.767 1.478,1.923 1.239,0.156 10 Ignition Switch ON

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation) [A].

4.

Turn the ignition switch off.

5.

With the engine stopped, leave the vehicle as is for 7.5 hours or more [B].

6.

Start the engine and wait 60 seconds or more [C].

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

8.

Read the pending DTC.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P011B.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



12.

If the judgment result shows INCOMPLETE or N/A, perform steps [A] through [D] again.

13.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P011B)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
P011B A
P011B and other DTCs B

HINT:

If any DTCs other than P011B are output, troubleshoot those DTCs first.




A

2.READ VALUE USING TECHSTREAM (INTAKE AIR TEMPERATURE)

B

2.READ VALUE USING TECHSTREAM (INTAKE AIR TEMPERATURE)
a.

Leave the vehicle for 7 hours or more.

HINT:

It is necessary leave the vehicle for 7 hours or more to allow conditions similar to the DTC detection conditions.



b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch ON.


d.

Turn the Techstream on.


e.

Enter the following menus: Powertrain / Engine and ECT / All Data / Intake Air.


f.

Read the value displayed on the Techstream.

OK:

Difference between the intake air temperature and the actual outside air temperature is within 10°C (18°F).


HINT:
·

Temperature readings on the vehicle outside temperature gauge (if equipped) are not suitable for comparing to the IAT reading. The outside temperature gauge has a significant delay built-in to prevent temperature swings from being displayed on its display. Use an accurate thermometer to determine the outside air temperature.

·

Perform "Inspection After Repair" after replacing the mass air flow meter (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).





OK

3.READ VALUE USING TECHSTREAM (COOLANT TEMPERATURE)

NG

3.READ VALUE USING TECHSTREAM (COOLANT TEMPERATURE)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / All Data / Coolant Temp.


e.

Read the value displayed on the Techstream.

OK:

The difference between the coolant temperature and the actual outside air temperature is within 10°C (18°F).


HINT:
·

If the result is not as specified, check that there are heat sources such as a block heater in the engine compartment.

·

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).





OK

NG