A Flexible Fuel Vehicle (FFV) can be used with a fuel containing a high concentration of ethyl alcohol.
This FFV uses a fuel pressure switching system which changes the fuel pressure to low or high using a fuel pressure switching valve.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P109C | The fuel pressure switching valve relay circuit is open or shorted to ground.
(1 trip detection logic) |
·
Fuel pressure switching valve circuit ·
F/PMP VSV relay ·
ECM |
| P109D | The fuel pressure switching valve relay circuit is shorted to the power supply.
(1 trip detection logic) |
·
Fuel pressure switching valve circuit ·
F/PMP VSV relay ·
ECM |
These DTCs are stored when a malfunction is detected in the fuel pressure switching valve circuit. If the voltage of the fuel pressure switching valve circuit is different from the voltage commanded by the ECM, the ECM determines that the fuel pressure switching valve circuit is open or shorted, and stores a DTC.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Even if no DTCs are stored, perform the DTC clear operation to start alcohol concentration learning.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Wait 3 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the pending DTC.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P109C or P109D.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Remove the fuel pressure control valve relay (F/PMP VSV) from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | When no battery voltage applied to terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | When battery voltage applied to terminals 1 and 2 | Below 1 Ω |
OK
NG
Remove the fuel pressure control valve relay (F/PMP VSV) from the engine room relay block.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F/PMP VSV relay (2) - Body ground | Ignition switch ON | 11 to 14 V |
| F/PMP VSV relay (5) - Body ground | Ignition switch ON | 11 to 14 V |
OK
NG
Remove the fuel pressure control valve relay (F/PMP VSV) from the engine room relay block.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F/PMP VSV relay (1) - D56-60 (FPCR) | Always | Below 1 Ω |
| F/PMP VSV relay (1) or D56-60 (FPCR) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the integration relay (EFI MAIN) from the engine room relay block.
Remove the fuel pressure control valve relay (F/PMP VSV) from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F/PMP VSV relay (2) - 1B-4 | Always | Below 1 Ω |
| F/PMP VSV relay (5) - 1B-4 | Always | Below 1 Ω |
| F/PMP VSV relay (2) or 1B-4 - Body ground | Always | 10 kΩ or more |
| F/PMP VSV relay (5) or 1B-4 - Body ground | Always | 10 kΩ or more |
OK
NG