Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM
RM27L0U _51 Engine / Hybrid System _049294 3UR-FE ENGINE CONTROL _0235547 SFI SYSTEM U

3UR-FE ENGINE CONTROL  SFI SYSTEM  TERMINALS OF ECM  


CHECK ECM


U153031E02
2.792,0.333 3.083,0.51 0.292,0.177 10 false D56 5.448,0.354 5.771,0.531 0.323,0.177 10 false A27

a.

Measure the voltage according to the value(s) in the table below.

HINT:

The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
A27-1 (BATT) - D56-81 (E1) L - BR Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
D56-41 (+BM) - D56-81 (E1) P - BR Power source of throttle actuator Always 11 to 14 V
A27-28 (IGSW) - D56-81 (E1) LG - BR Ignition switch Ignition switch ON 11 to 14 V
A27-3 (+B) - D56-81 (E1) GR - BR Power source of ECM Ignition switch ON 11 to 14 V
A27-2 (+B2) - D56-81 (E1) GR - BR Power source of ECM Ignition switch ON 11 to 14 V
D56-58 (OC1+) - D56-57 (OC1-) B - B-L Camshaft timing oil control valve (OCV) (for Intake Side of Bank 1) Idling Pulse generation
(see waveform 1)
D56-52 (OC2+) - D56-51 (OC2-) L-B - R-B Camshaft timing oil control valve (OCV) (for Intake Side of Bank 2) Idling Pulse generation
(see waveform 1)
D56-56 (OE1+) - D56-55 (OE1-) L-W - L-B Camshaft timing oil control valve (OCV) (for Exhaust Side of Bank 1) Idling Pulse generation
(see waveform 1)
D56-50 (OE2+) - D56-49 (OE2-) L-R - L Camshaft timing oil control valve (OCV) (for Exhaust Side of Bank 2) Idling Pulse generation
(see waveform 1)
A27-34 (MREL) - D56-81 (E1) W - BR EFI MAIN relay Ignition switch ON 11 to 14 V
D56-74 (VG) - D56-75 (E2G) L-Y - G-W Mass air flow meter Idling, Shift lever position P or N, A/C switch OFF 0.5 to 3.0 V
D56-73 (THA) - D56-97 (ETHW) Y-B - BR Intake air temperature sensor Idling, Intake air temperature 20°C (68°F) 0.5 to 3.4 V
D56-76 (THW) - D56-98 (ETHA) G-B - BR Engine coolant temperature sensor Idling, Engine coolant temperature 80°C (176°F) 0.2 to 1.0 V
D56-80 (VCTA) - D56-79 (ETA) Y - L Power source of throttle position sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
D56-78 (VTA1) - D56-79 (ETA) R-Y - L Throttle position sensor (for engine control) Ignition switch ON,
Throttle valve fully closed
0.5 to 1.2 V
Ignition switch ON,
Throttle valve fully open
3.2 to 4.8 V
D56-77 (VTA2) - D56-79 (ETA) Y-B - L Throttle position sensor (for sensor malfunction detection) Ignition switch ON,
Throttle valve fully closed
2.1 to 3.1 V
Ignition switch ON,
Throttle valve fully open
4.5 to 5.5 V
A27-55 (VPA) - A27-58 (EPA) W - BE Accelerator pedal position sensor (for engine control) Ignition switch ON,
Accelerator pedal released
0.5 to 1.1 V
Ignition switch ON,
Accelerator pedal fully depressed
2.6 to 4.5 V
A27-56 (VPA2) - A27-60 (EPA2) LG - BR Accelerator pedal position sensor (for sensor malfunctioning detection) Ignition switch ON,
Accelerator pedal released
1.2 to 2.0 V
Ignition switch ON,
Accelerator pedal fully depressed
3.4 to 4.7 V
A27-57 (VCPA) - A27-58 (EPA) B - BE Power source of accelerator pedal position sensor (for VPA) Ignition switch ON 4.5 to 5.5 V
A27-59 (VCP2) - A27-60 (EPA2) V - BR Power source of accelerator pedal position sensor (for VPA2) Ignition switch ON 4.5 to 5.5 V
D56-22 (HA1A) - D56-23 (E04) L - W-B A/F sensor heater Idling Below 3.0 V
Ignition switch ON 11 to 14 V
D56-20 (HA2A) - D56-21 (E05) G - W-B A/F sensor heater Idling Below 3.0 V
Ignition switch ON 11 to 14 V
D56-126 (A1A+) - D56-81 (E1) G -BR A/F sensor Ignition switch ON 3.3 V*1
D56-125 (A1A-) - D56-81 (E1) R - BR A/F sensor Ignition switch ON 2.9 V*1
D56-103 (A2A+) - D56-81 (E1) P - BR A/F sensor Ignition switch ON 3.3 V*1
D56-102 (A2A-) - D56-81 (E1) L - BR A/F sensor Ignition switch ON 2.9 V*1
D56-45 (HT1B) - D56-46 (E03) G-B - W-B Heated oxygen sensor heater Idling Below 3.0 V
Ignition switch ON 11 to 14 V
D56-44 (HT2B) - D56-46 (E03) B - W-B Heated oxygen sensor heater Idling Below 3.0 V
Ignition switch ON 11 to 14 V
D56-114 (OX1B) - D56-115 (EX1B) G - L Heated oxygen sensor Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor Pulse generation
(see waveform 2)
D56-112 (OX2B) - D56-113 (EX2B) R - W Heated oxygen sensor Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor Pulse generation
(see waveform 2)
D56-86 (#10) - D56-43 (E01) R-L - W-B Injector Ignition switch ON 11 to 14 V
Idling Pulse generation
(see waveform 3)
D56-109 (#20) - D56-43 (E01) L - W-B Injector Ignition switch ON 11 to 14 V
Idling Pulse generation
(see waveform 3)
D56-85 (#30) - D56-43 (E01) R - W-B Injector Ignition switch ON 11 to 14 V
Idling Pulse generation
(see waveform 3)
D56-108 (#40) - D56-43 (E01) Y - W-B Injector Ignition switch ON 11 to 14 V
Idling Pulse generation
(see waveform 3)
D56-84 (#50) - D56-43 (E01) G - W-B Injector Ignition switch ON 11 to 14 V
Idling Pulse generation
(see waveform 3)
D56-107 (#60) - D56-43 (E01) R - W-B Injector Ignition switch ON 11 to 14 V
Idling Pulse generation
(see waveform 3)
D56-83 (#70) - D56-43 (E01) W - W-B Injector Ignition switch ON 11 to 14 V
Idling Pulse generation
(see waveform 3)
D56-106 (#80) - D56-43 (E01) R-B - W-B Injector Ignition switch ON 11 to 14 V
Idling Pulse generation
(see waveform 3)
D56-94 (KNK1) - D56-93 (EKNK) R - G Knock sensor Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(see waveform 4)
D56-117 (KNK2) - D56-116 (EKN2) W - B Knock sensor Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(see waveform 4)
D56-96 (KNK3) - D56-95 (EKN3) W - B Knock sensor Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(see waveform 4)
D56-119 (KNK4) - D56-118 (EKN4) R - G Knock sensor Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(see waveform 4)
D56-92 (VV1+) - D56-91 (VV1-) R - G Variable valve timing (VVT) sensor (for Intake Side of Bank 1) Idling Pulse generation
(see waveform 5)
D56-87 (VV2+) - D56-88 (VV2-) R - Y Variable valve timing (VVT) sensor (for Intake Side for Bank 2) Idling Pulse generation
(see waveform 5)
D56-69 (EV1+) - D56-68 (EV1-) R-L - B Variable valve timing (VVT) sensor (for Exhaust Side of Bank 1) Idling Pulse generation
(see waveform 16)
D56-64 (EV2+) - D56-65 (EV2-) R-L - B Variable valve timing (VVT) sensor (for Exhaust Side of Bank 2) Idling Pulse generation
(see waveform 16)
D56-110 (NE+) - D56-111 (NE-) W - Y Crankshaft position sensor Idling Pulse generation
(see waveform 5)
D56-40 (IGT1) - D56-81 (E1) B-Y - BR Ignition coil (ignition signal) Idling Pulse generation
(see waveform 6)
D56-33 (IGT2) - D56-81 (E1) L-Y - BR Ignition coil (ignition signal) Idling Pulse generation
(see waveform 6)
D56-37 (IGT3) - D56-81 (E1) B - BR Ignition coil (ignition signal) Idling Pulse generation
(see waveform 6)
D56-34 (IGT4) - D56-81 (E1) L-B - BR Ignition coil (ignition signal) Idling Pulse generation
(see waveform 6)
D56-35 (IGT5) - D56-81 (E1) G-R - BR Ignition coil (ignition signal) Idling Pulse generation
(see waveform 6)
D56-36 (IGT6) - D56-81 (E1) G - BR Ignition coil (ignition signal) Idling Pulse generation
(see waveform 6)
D56-38 (IGT7) - D56-81 (E1) G-W - BR Ignition coil (ignition signal) Idling Pulse generation
(see waveform 6)
D56-39 (IGT8) - D56-81 (E1) G-B - BR Ignition coil (ignition signal) Idling Pulse generation
(see waveform 6)
D56-104 (IGF1) - D56-81 (E1) G-B - BR Ignition coil (ignition confirmation signal) Ignition switch ON 4.5 to 5.5 V
Idling Pulse generation
(see waveform 6)
D56-105 (IGF2) - D56-81 (E1) R - BR Ignition coil (ignition confirmation signal) Ignition switch ON 4.5 to 5.5 V
Idling Pulse generation
(see waveform 6)
D56-63 (PRG) - D56-81 (E1) L-B - BR Purge VSV Ignition switch ON 11 to 14 V
Idling Pulse generation
(see waveform 7)
A27-13 (SPD) - D56-81 (E1) B - BR Speed signal from combination meter Driving at 20 km/h (12 mph) Pulse generation
(see waveform 8)
A27-46 (STA) - D56-81 (E1) R - BR Starter signal Cranking 5.5 V or more
D56-120 (NSW) - D56-81 (E1) L - BR Park / neutral position switch Ignition switch ON, Shift lever position other than P and N 11 to 14 V
Ignition switch ON, Shift lever position in P or N Below 3.0 V
A27-26 (STP) - D56-81 (E1) LG - BR Stop light switch Brake pedal depressed 7.5 to 14 V
Brake pedal released Below 1.5 V
A27-35 (ST1-) - D56-81 (E1) R - BR Stop light switch
(opposite to STP terminal)
Ignition switch ON,
Brake pedal depressed
Below 1.5 V
Ignition switch ON,
Brake pedal released
7.5 to 14 V
D56-19 (M+) - D56-82 (ME01) R - W-B Throttle actuator Idling with warm engine Pulse generation
(see waveform 9)
D56-18 (M-) - D56-82 (ME01) G - W-B Throttle actuator Idling with warm engine Pulse generation
(see waveform 10)
A27-52 (FPC) - D56-81 (E1) BE - BR Fuel pump control Ignition switch ON Below 1.5 V
A27-24 (W) - D56-81 (E1) P - BR MIL Ignition switch ON Below 3.0 V
Idling 11 to 14 V
A27-16 (TC) - D56-81 (E1) R - BR Terminal TC of DLC3 Ignition switch ON 11 to 14 V
A27-15 (TACH) - D56-81 (E1) W - BR Engine speed Idling Pulse generation
(see waveform 11)
A27-30 (VPMP) - D56-81 (E1) V - BR Vent valve (built into canister pump module) Ignition switch ON 11 to 14 V
A27-49 (MPMP) - D56-81 (E1) G - BR Leak detection pump (built into canister pump module) Leak detection pump OFF Below 3.0 V
Leak detection pump ON 11 to 14 V
D56-67 (VCV1) - D56-97 (ETHW) L - BR Power source for sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
D56-66 (VCV2) - D56-97 (ETHW) L - BR Power source for sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
D56-121 (PPMP) - D56-97 (ETHW) P - BR Canister pressure sensor (built into canister pump module) Ignition switch ON 3.3 to 4.0 V
D56-32 (ALT) - D56-81 (E1) R - BR Generator Ignition switch ON 11 to 14 V
A27-10 (CANH) - D56-81 (E1) GR - BR CAN communication line Ignition switch ON Pulse generation
(see waveform 12)
A27-11 (CANL) - D56-81 (E1) W - BR CAN communication line Ignition switch ON Pulse generation
(see waveform 13)
D56-62 (ACIS) - D56-81 (E1) L-Y - BR VSV for ACIS (Acoustic Control Induction System) operation signal Ignition switch ON 11 to 14 V
D56-28 (AIRV) - D56-81 (E1) BR - BR Air switching valve for secondary air injection system Ignition switch ON 11 to 14 V
D56-54 (AIRP) - D56-81 (E1) P - BR Air pump control Ignition switch ON 11 to 14 V
D56-30 (AIDI) - D56-81 (E1) G - BR Diagnostic information signal for secondary air injection system Air injection system operates Pulse generation
(see waveform 15)
A27-54 (AIP) - D56-98 (ETHA) Y - BR Secondary air injection system pressure signal Ignition switch ON 3.0 to 3.6 V
A27-43 (ARV2) - D56-81 (E1) V - BR Air switching valve for secondary air injection system Ignition switch ON 11 to 14 V
D56-53 (ARP2) - D56-81 (E1) P-L - BR Air pump control Ignition switch ON 11 to 14 V
D56-29 (AID2) - D56-81 (E1) G-Y - BR Diagnostic information signal for secondary air injection system Air injection system operates Pulse generation
(see waveform 15)
A27-53 (AIP2) - D56-97 (ETHW) G - BR Secondary air injection system pressure signal Ignition switch ON 3.0 to 3.6 V
D56-61 (HAI1) - D56-81 (E1) B - BR Air pump heater for secondary air injection system AI heater operating 11 to 14 V
D56-90 (G2) - D56- 89 (G2-) R - B Camshaft position sensor Idling Pulse generation
(see waveform 14)
A27-14 (STSW) - D56-81 (E1) BR - BR Starter switch Shift lever position P or N, Cranking 6.0 V or more
A27-41 (ACCR) - D56-81 (E1) BR - BR ACC relay control signal Ignition switch ON → Cranking 11 to 14 V → Below 1 V
D56-16 (STAR) - D56-81 (E1) L - BR Starter relay control Ignition switch ON Below 1.5 V
Cranking 5.5 V or more
D56-72 (PSP) - D56-81 (E1) G - BR Power steering oil pressure sensor Ignition switch ON 0.5 to 4.5 V
A27-4 (ADJ1)*2 - Body ground W-B - Body ground Vehicle type designation wire harness Always Below 1 V

HINT:

*1: The ECM terminal voltage is constant regardless of the output voltage from the sensor.

*2: for 2WD only



b.
U115314E02
0.51,0.177 1.198,0.375 0.688,0.198 10 false 5 V/DIV. 0.552,1.104 0.99,1.302 0.438,0.198 10 false GND 1.802,1.833 2.698,2.031 0.896,0.198 10 false 1 msec./DIV.

WAVEFORM 1:

Camshaft timing oil control valve (OCV)
Terminal No. (Symbols) Tool Setting Condition
D56-58 (OC1+) - D56-57 (OC1-) 5 V/DIV., 1 msec./DIV. Idling
D56-52 (OC2+) - D56-51 (OC2-) 5 V/DIV., 1 msec./DIV. Idling
D56-56 (OE1+) - D56-55 (OE1-) 5 V/DIV., 1 msec./DIV. Idling
D56-50 (OE2+) - D56-49 (OE2-) 5 V/DIV., 1 msec./DIV. Idling


c.
U115312E02
0.313,0.146 1.031,0.365 0.719,0.219 10 false 0.2 V/DIV. 0.531,1.479 0.917,1.677 0.385,0.198 10 false GND 1.802,1.865 2.802,2.063 1,0.198 10 false 200 msec./DIV.

WAVEFORM 2:

Heated oxygen sensor
Terminal No. (Symbols) Tool Setting Condition
D56-114 (OX1B) - D56-115 (EX1B) 0.2 V/DIV., 200 msec./DIV. Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor
D56-112 (OX2B) - D56-113 (EX2B) 0.2 V/DIV., 200 msec./DIV. Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor

HINT:

In DATA LIST, item O2S B1S2 and O2S B2S2 show the ECM input values from the heated oxygen sensor.



d.
A363802E01
0.49,0.219 1.167,0.417 0.677,0.198 10 false 20 V/DIV. 1.833,1.885 2.792,2.063 0.958,0.177 10 false 20 msec./DIV. 0.604,1.573 0.99,1.771 0.385,0.198 10 false GND

WAVEFORM 3:

Injector No. 1 (to No. 8) injection signal
Terminal No. (Symbols) Tool Setting Condition
D56-86 (#10) - D56-43 (E01) 20 V/DIV., 20 msec./DIV. Idling
D56-109 (#20) - D56-43 (E01) 20 V/DIV., 20 msec./DIV. Idling
D56-85 (#30) - D56-43 (E01) 20 V/DIV., 20 msec./DIV. Idling
D56-108 (#40) - D56-43 (E01) 20 V/DIV., 20 msec./DIV. Idling
D56-84 (#50) - D56-43 (E01) 20 V/DIV., 20 msec./DIV. Idling
D56-107 (#60) - D56-43 (E01) 20 V/DIV., 20 msec./DIV. Idling
D56-83 (#70) - D56-43 (E01) 20 V/DIV., 20 msec./DIV. Idling
D56-106 (#80) - D56-43 (E01) 20 V/DIV., 20 msec./DIV. Idling

HINT:

The wavelength becomes shorter as the engine rpm increases.



e.
A357198E02
2.406,0.531 3.052,0.708 0.646,0.177 10 false 1 V/DIV. 1.135,1.896 2.063,2.094 0.927,0.198 10 false 1 msec./DIV. 2.615,0.99 3.063,1.198 0.448,0.208 10 false GND

WAVEFORM 4:

Knock sensor
Terminal No. (Symbols) Tool Setting Condition
D56-94 (KNK1) - D56-93 (EKNK) 1 V/DIV., 1 msec./DIV. Engine speed maintained at 4000 rpm after warming up engine
D56-117 (KNK2) - D56-116 (EKN2) 1 V/DIV., 1 msec./DIV. Engine speed maintained at 4000 rpm after warming up engine
D56-96 (KNK3) - D56-95 (EKN3) 1 V/DIV., 1 msec./DIV. Engine speed maintained at 4000 rpm after warming up engine
D56-119 (KNK4) - D56-118 (EKN4) 1 V/DIV., 1 msec./DIV. Engine speed maintained at 4000 rpm after warming up engine

HINT:
·

The wavelength becomes shorter as the engine rpm increases.

·

The waveforms and amplitudes displayed differ slightly depending on the vehicle.




f.
A217926E01
0.24,1.161 0.470,1.326 0.230,0.165 10 (a) 0.24,1.707 0.455,1.859 0.215,0.151 10 (b) 0.24,2.075 0.479,2.280 0.239,0.206 10 (c) 2.819,1.267 3.155,1.416 0.336,0.149 10 GND 2.819,2.197 3.155,2.346 0.336,0.149 10 GND 2.819,1.815 3.155,1.964 0.336,0.149 10 GND 1.112,2.501 2.032,2.642 0.921,0.141 10 20 msec./DIV. 2.701,0.773 3.265,0.929 0.563,0.156 10 5 V/DIV.

WAVEFORM 5:

Crankshaft position sensor and VVT sensor for intake side
Terminal No. (Symbols) Tool Setting Condition
(a) D56-110 (NE+) - D56-111 (NE-) 5 V/DIV., 20 msec./DIV. Idle after engine warmed up
(b) D56-92 (VV1+) - D56-91 (VV1-) 5 V/DIV., 20 msec./DIV. Idle after engine warmed up
(c) D56-87 (VV2+) - D56-88 (VV2-) 5 V/DIV., 20 msec./DIV. Idle after engine warmed up

HINT:

The wavelength becomes shorter as engine rpm increases.



g.
A379410E03
0.594,0.115 1.188,0.292 0.594,0.177 10 false 2 V/DIV. 0.469,0.896 0.979,1.083 0.51,0.188 10 false Ground 0.469,1.458 0.99,1.656 0.521,0.198 10 false Ground 0.938,0.719 1.177,0.906 0.24,0.188 10 false (a) 0.927,1.26 1.167,1.448 0.24,0.188 10 false (b) 1.833,1.813 2.854,1.99 1.021,0.177 10 false 20 msec./DIV.

WAVEFORM 6:

Igniter IGT signal (from ECM to igniter) and Igniter IGF signal (from igniter to ECM)
Terminal No. (Symbols) Tool Setting Condition
(a) D56-40 (IGT1) - D56-81 (E1) 2 V/DIV., 20 msec./DIV. Idling
(a) D56-33 (IGT2) - D56-81 (E1) 2 V/DIV., 20 msec./DIV. Idling
(a) D56-37 (IGT3) - D56-81 (E1) 2 V/DIV., 20 msec./DIV. Idling
(a) D56-34 (IGT4) - D56-81 (E1) 2 V/DIV., 20 msec./DIV. Idling
(a) D56-35 (IGT5) - D56-81 (E1) 2 V/DIV., 20 msec./DIV. Idling
(a) D56-36 (IGT6) - D56-81 (E1) 2 V/DIV., 20 msec./DIV. Idling
(a) D56-38 (IGT7) - D56-81 (E1) 2 V/DIV., 20 msec./DIV. Idling
(a) D56-39 (IGT8) - D56-81 (E1) 2 V/DIV., 20 msec./DIV. Idling
(b) D56-104 (IGF1) - D56-81 (E1) 2 V/DIV., 20 msec./DIV. Idling
(b) D56-105 (IGF2) - D56-81 (E1) 2 V/DIV., 20 msec./DIV. Idling

HINT:

The wavelength becomes shorter as engine rpm increases.



h.
A218020E08
2.677,0.208 3.344,0.51 0.667,0.302 10 10 V/DIV. 2.802,0.938 3.292,1.26 0.49,0.323 10 GND 1.26,1.771 2.25,2.021 0.99,0.25 10 20 ms./DIV.

WAVEFORM 7:

Purge VSV
Terminal No. (Symbols) Tool Setting Condition
D56-63 (PRG) - D56-81 (E1) 10 V/DIV., 10 to 100 msec./DIV. Idling

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



i.
U115313E02
0.396,0.229 1.083,0.427 0.688,0.198 10 false 2 V/DIV. 0.49,1.146 0.885,1.344 0.396,0.198 10 false GND 1.625,1.896 2.583,2.094 0.958,0.198 10 false 20 msec./DIV.

WAVEFORM 8:

Vehicle speed signal
Terminal No. (Symbols) Tool Setting Condition
A27-13 (SPD) - D56-81 (E1) 2 V/DIV., 20 msec./DIV. Driving at 20 km/h (12 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



j.
A208000E06
2.856,0.973 3.186,1.119 0.330,0.146 10 GND 2.631,0.216 3.176,0.360 0.545,0.144 10 5 V/DIV. 0.501,0.616 0.722,0.759 0.221,0.143 10 M+ 1.237,1.806 2.058,1.964 0.820,0.158 10 1 msec./DIV.

WAVEFORM 9:

Throttle actuator positive terminal
Terminal No. (Symbols) Tool Setting Condition
D56-19 (M+) - D56-82 (ME01) 5 V/DIV., 1 msec./DIV. Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



k.
A245848E04
2.849,0.99 3.182,1.142 0.333,0.151 10 GND 2.627,0.266 3.166,0.409 0.539,0.142 10 5 V/DIV. 0.479,0.626 0.664,0.777 0.184,0.15 10 M- 1.246,1.82 2.076,1.967 0.83,0.147 10 1 msec./DIV.

WAVEFORM 10:

Throttle actuator negative terminal
Terminal No. (Symbols) Tool Setting Condition
D56-18 (M-) - D56-82 (ME01) 5 V/DIV., 1 msec./DIV. Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



l.
A378423E01
0.573,0.656 1.208,0.854 0.635,0.198 10 false 5 V/DIV. 0.635,2.042 1.063,2.229 0.427,0.188 10 false GND 1.74,2.677 2.833,2.875 1.094,0.198 10 false 10 msec./DIV.

WAVEFORM 11:

Engine speed signal
Terminal No. (Symbols) Tool Setting Condition
A27-15 (TACH) - D56-81 (E1) 5 V/DIV., 10 msec./DIV. Idling

HINT:

The wavelength becomes shorter as the engine rpm increases.



m.
A357201E02
2.979,1.396 3.385,1.594 0.406,0.198 10 false GND 2.76,0.292 3.323,0.479 0.563,0.188 10 false 1 V/DIV. 1.469,1.896 2.469,2.083 1,0.188 10 false 10 μsec./DIV.

WAVEFORM 12:

CAN communication signal
Terminal No. (Symbols) Tool Setting Condition
A27-10 (CANH) - D56-81 (E1) 1 V/DIV., 10 μsec./DIV. Engine stops and ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



n.
A357202E02
3.01,1.354 3.385,1.531 0.375,0.177 10 false GND 2.771,0.229 3.385,0.417 0.615,0.188 10 false 1 V/DIV. 1.448,1.865 2.354,2.063 0.906,0.198 10 false 10 μsec./DIV.

WAVEFORM 13:

CAN communication signal
Terminal No. (Symbols) Tool Setting Condition
A27-11 (CANL) - D56-81 (E1) 1 V/DIV., 10 μsec./DIV. Engine stops and ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



o.
A211721E01
2.827,1.417 3.206,1.598 0.379,0.181 10 GND 2.827,1.965 3.206,2.145 0.379,0.180 10 GND 0.146,1.87 0.458,2.033 0.312,0.163 10 CH2 0.146,1.321 0.456,1.484 0.310,0.163 10 CH1 1.123,2.469 2.063,2.645 0.941,0.177 10 20 msec./DIV. 2.696,0.738 3.261,0.914 0.566,0.177 10 5 V/DIV.

WAVEFORM 14:

Crankshaft position sensor and camshaft position sensor
Terminal No. (Symbols) Tool Setting Condition
CH1: D56-110 (NE+) - D56-111 (NE-) 5 V/DIV., 20 msec./DIV. Idle after engine warmed up
CH2: D56-90 (G2) - D56-89 (G2-) 5 V/DIV., 20 msec./DIV. Idle after engine warmed up

HINT:

The wavelength becomes shorter as the engine rpm increases.



p.
A255990E01
2.962,0.998 3.299,1.147 0.337,0.149 10 GND 2.786,0.225 3.328,0.374 0.542,0.149 10 5 V/DIV. 1.2,1.789 2.096,1.938 0.896,0.149 10 50 msec./DIV.

WAVEFORM 15:

Terminal DI of air injection control driver
Terminal No. (Symbols) Tool Setting Condition
D56-30 (AIDI) - D56-81 (E1) 5 V/DIV., 50 msec./DIV. Performing system check using Techstream (air injection check)
D56-29 (AID2) - D56-81 (E1) 5 V/DIV., 50 msec./DIV. Performing system check using Techstream (air injection check)

HINT:

The wavelength changes when the air injection control driver detects malfunctions in the secondary air injection system (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>P0412).



q.
A217927E01
0.263,1.166 0.493,1.331 0.230,0.165 10 (a) 0.263,1.711 0.459,1.894 0.196,0.183 10 (b) 0.263,2.083 0.473,2.252 0.210,0.169 10 (c) 2.827,1.272 3.164,1.421 0.336,0.149 10 GND 2.827,2.197 3.164,2.346 0.336,0.149 10 GND 2.827,1.824 3.164,1.973 0.336,0.149 10 GND 1.097,2.511 2.017,2.652 0.921,0.141 10 20 msec./DIV. 2.708,0.79 3.271,0.946 0.563,0.156 10 5 V/DIV.

WAVEFORM 16:

Crankshaft position sensor and VVT sensor for exhaust side
Terminal No. (Symbols) Tool Setting Condition
(a) D56-110 (NE+) - D56-111 (NE-) 5 V/DIV., 20 msec./DIV. Idle after engine warmed up
(b) D56-69 (EV1+) - D56-68 (EV1-) 5 V/DIV., 20 msec./DIV. Idle after engine warmed up
(c) D56-64 (EV2+) - D56-65 (EV2-) 5 V/DIV., 20 msec./DIV. Idle after engine warmed up

HINT:

The wavelength becomes shorter as engine rpm increases.