Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM
RM27L0U _51 Engine / Hybrid System _049294 3UR-FE ENGINE CONTROL _0235547 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P0443  Evaporative Emission Control System Purge Control Valve Circuit  


DESCRIPTION

HINT:

This DTC P0443 is applicable to Mexico models only.


To reduce hydrocarbon emissions, evaporated fuel from the fuel tank is routed through a charcoal canister to the intake manifold for combustion in the cylinders.

The ECM changes the duty signals to the Purge VSV (Vacuum Switching Valve for Purge Control) so that the intake amount of hydrocarbon emissions is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC Code DTC Detection Condition Trouble Area
P0443 Terminal voltage of ECM output circuit does not correspond with drive signals from ECM to purge VSV
(1 trip detection logic)
·

Open or short in purge VSV circuit

·

Purge VSV

·

ECM



WIRING DIAGRAM

A196661E13
0.792,2.531 1.344,2.74 0.552,0.208 10 false Battery 1.208,2.052 2.354,2.281 1.146,0.229 10 false Integration Relay 0.865,0.813 1.042,1 0.177,0.188 10 false 3 0.813,1 1.063,1.177 0.25,0.177 10 false 1B 0.854,1.385 1.031,1.573 0.177,0.188 10 false 1 0.802,1.635 1.052,1.813 0.25,0.177 10 false 1C 2.594,1.438 2.771,1.625 0.177,0.188 10 false 4 2.542,1.635 2.792,1.813 0.25,0.177 10 false 1B 2.594,0.813 2.771,1 0.177,0.188 10 false 2 2.542,1 2.792,1.177 0.25,0.177 10 false 1B 5.344,1.438 5.646,1.625 0.302,0.188 10 false 63 5.281,1.625 5.635,1.823 0.354,0.198 10 false D56 5.344,0.802 5.573,0.99 0.229,0.188 10 false 34 5.281,1 5.594,1.177 0.313,0.177 10 false A27 5.646,0.99 6.167,1.188 0.521,0.198 10 false MREL 5.635,1.531 6.01,1.698 0.375,0.167 10 false PRG 4.094,1.917 4.479,2.146 0.385,0.229 10 false D16 4.094,2.063 4.885,2.26 0.792,0.198 10 false Purge VSV 3.052,1.802 3.844,2 0.792,0.198 10 false EFI NO. 2 1.094,1.771 1.885,1.969 0.792,0.198 10 false EFI NO. 1 3.156,1.479 3.333,1.667 0.177,0.188 10 false 1 3.552,1.479 3.729,1.667 0.177,0.188 10 false 2 4.052,1.469 4.229,1.656 0.177,0.188 10 false 1 4.781,1.469 4.958,1.656 0.177,0.188 10 false 2 1.792,0.615 2.583,0.813 0.792,0.198 10 false EFI MAIN 6.083,2.385 6.479,2.573 0.396,0.188 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (ACTIVATE THE VSV FOR EVAP CONTROL)
a.
A200511E01
0.55,0.157 1.109,0.306 0.559,0.149 10 VSV ON 2.222,0.157 2.843,0.306 0.621,0.149 10 VSV OFF 0.593,1.471 1.152,1.627 0.559,0.156 10 Air flows 1.985,1.471 3.058,1.627 1.073,0.156 10 Air does not flow

Connect a Techstream to the DLC3.


b.

Disconnect the vacuum hose (charcoal canister side) from the purge VSV.


c.

Start the engine.


d.

Turn the Techstream on.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for EVAP Control.


f.

Operate the purge VSV and check the airflow.

OK:
Tester Operation Specified Condition
VSV ON Purge VSV port applies suction to finger
VSV OFF Purge VSV port applies no suction to finger




OK

NG

2.INSPECT PURGE VSV (RESISTANCE)
2.INSPECT PURGE VSV (RESISTANCE)
a.
A152887E02
0.087,0.083 2.597,0.443 2.510,0.360 10 Component without harness connected: (Purge VSV)

Disconnect the D16 purge VSV connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 26 to 30 Ω




OK

3.INSPECT PURGE VSV (POWER SOURCE)

NG

3.INSPECT PURGE VSV (POWER SOURCE)
a.
U152990E02
0.135,0.115 2.49,0.479 2.354,0.365 10 false Front view of wire harness connector: (to Purge VSV) 0.448,1.854 0.813,2.104 0.365,0.25 10 false D16

Disconnect the D16 purge VSV connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D16-1 - Body ground Ignition switch ON 11 to 14 V




OK

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (PURGE VSV - INTEGRATION RELAY)
4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Disconnect the D16 purge VSV connector.


b.

Disconnect the D56 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D16-2 - D56-63 (PRG) Always Below 1 Ω
D16-2 or D56-63 (PRG) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (PURGE VSV - INTEGRATION RELAY)
a.

Check the EFI NO. 2 fuse.

i.

Remove the EFI NO. 2 fuse from the engine room relay block.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI No. 2 fuse Always Below 1 Ω



iii.

Reinstall the EFI NO. 2 fuse.



b.

Disconnect the D16 purge VSV connector.


c.

Remove the integration relay from the engine room relay block.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D16-1 - 1B-4 Always Below 1 Ω
D16-1 or 1B-4 - Body ground Always 10 kΩ or higher




OK

REPAIR OR REPLACE ECM POWER SOURCE CIRCUIT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR AND REPLACE FUSE