Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM
RM27L0U _51 Engine / Hybrid System _049294 3UR-FE ENGINE CONTROL _0235547 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P0724  Brake Switch "B" Circuit High  


DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling while driving in the lock-up condition when the brakes are suddenly applied.

When the brake pedal is depressed, this switch sends a signal to the ECM. Then the ECM cancels the operation of the lock-up clutch while braking is in progress.

DTC Code DTC Detection Condition Trouble Area
P0724 Stop light switch remains ON even when vehicle is driven in GO (30 km/h (18.65 mph) or more) and STOP (less than 3 km/h (1.86 mph)) pattern 5 times (2 trip detection logic)
·

Short in stop light switch signal circuit

·

Stop light switch

·

ECM



MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains ON. When the stop light switch remains ON during GO and STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM stores the DTC. The vehicle must GO (30 km/h (18.65 mph) or more) and STOP (less than 3 km/h (1.86 mph)) 5 times for 2 driving cycles in order for the DTC to be output.

MONITOR STRATEGY

Related DTCs P0724: Stop light switch/Range check/Rationality
Required sensors/Components Stop light switch, Vehicle speed sensor
Frequency of operation Continuous
Duration GO and STOP 5 times
MIL operation 2 driving cycles
Sequence of operation None

TYPICAL ENABLING CONDITIONS

The monitor will run whenever this DTC is not present. None
Battery voltage 8 V or more
Starter OFF
Ignition switch ON
GO: Vehicle speed 30 km/h (18.65 mph) or more
STOP: Vehicle speed Less than 3 km/h (1.86 mph)

TYPICAL MALFUNCTION THRESHOLDS

Brake switch Stuck ON

CONFIRMATION DRIVING PATTERN

A199312E01
1.413,2.021 1.792,2.191 0.378,0.170 10 Idling 0.622,2.35 1.833,2.513 1.211,0.163 10 Ignition Switch ON 2.509,2.467 2.707,2.665 0.198,0.198 10 [A] 2.583,3.079 3.295,3.221 0.711,0.142 10 5 seconds 3.27,3.494 3.474,3.674 0.205,0.180 10 [B] 3.409,1.912 3.619,2.090 0.210,0.178 10 [C] 6.755,3.475 6.952,3.672 0.198,0.198 10 [E] 4.043,1.495 4.253,1.673 0.210,0.178 10 [D] 0.478,1.201 1.826,1.385 1.348,0.184 10 30 km/h (18.65 mph) 0.63,1.726 1.867,1.903 1.237,0.177 10 3 km/h (1.86 mph)

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Wait 5 seconds.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

8.

Read the Pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0724.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] through [E].



12.

Start the engine [C].

13.

Accelerate the vehicle to 30 km/h (18.65 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.86 mph) or less [D]. Repeat step [D] 5 times.

14.

Check the DTC judgment result [E].

15.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A185018E06
6.073,3.083 6.448,3.26 0.375,0.177 10 false ECM 5.677,0.792 6.031,0.958 0.354,0.167 10 false ST1- 5.688,1.563 6,1.719 0.313,0.156 10 false STP 5.396,0.729 5.615,0.885 0.219,0.156 10 false 35 5.344,1.677 5.677,1.844 0.333,0.167 10 false A27 5.344,0.917 5.667,1.073 0.323,0.156 10 false A27 5.406,1.479 5.604,1.646 0.198,0.167 10 false 26 4.198,1.927 4.406,2.094 0.208,0.167 10 false A4 4.188,2.083 5.344,2.281 1.156,0.198 10 false Stop Light Switch 5.094,0.771 5.198,0.938 0.104,0.167 10 false 3 5.094,1.531 5.208,1.698 0.115,0.167 10 false 1 4.292,0.781 4.396,0.948 0.104,0.167 10 false 4 4.292,1.542 4.396,1.708 0.104,0.167 10 false 2 3.646,1.042 3.958,1.208 0.313,0.167 10 false IGN 3.792,1.792 4.208,1.948 0.417,0.156 10 false STOP 2.604,1.823 2.885,1.979 0.281,0.156 10 false IG2 1.854,1.365 2.135,1.521 0.281,0.156 10 false IG2 2.188,1.365 2.292,1.531 0.104,0.167 10 false 6 1.083,1.365 1.188,1.531 0.104,0.167 10 false 5 1.25,1.365 1.573,1.521 0.323,0.156 10 false AM2 1.031,2.344 1.354,2.5 0.323,0.156 10 false AM2 0.479,2.26 0.875,2.594 0.396,0.333 10 false IG2 MAIN 3.698,3.635 3.99,3.792 0.292,0.156 10 false ALT 0.646,4.781 1.135,4.969 0.49,0.188 10 false Battery 1.385,1.906 1.708,2.063 0.323,0.156 10 false H10 1.385,2.063 2.333,2.25 0.948,0.188 10 false Ignition Switch

CAUTION / NOTICE / HINT

HINT:

Using the Techstream to read the Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


1.

Warm up the engine.

2.

Turn the ignition switch off.

3.

Connect the Techstream to the DLC3.

4.

Turn the ignition switch to ON.

5.

Turn the Techstream on.

6.

Enter the following menus: Powertrain / Engine and ECT / Data List.

7.

Follow the instructions on the Techstream and read the Data List.


Item Measurement Item/
Range (Display)
Normal Condition Diagnostic Note
Stop Light Switch Stop light switch status/
ON or OFF
·

Brake pedal is depressed: ON

·

Brake pedal is released: OFF


-

PROCEDURE

1.INSPECT STOP LIGHT SWITCH
A115657E35
1.927,2.344 2.365,2 false 1.594,2.344 1.135,2 false 1.979,2.563 2.344,2.667 false 1.531,2.563 1.125,2.688 false 0.521,1.792 1.115,1.479 false 0.083,0.813 0.906,0.99 0.823,0.177 10 false Not Pushed 2.094,0.833 2.635,1.031 0.542,0.198 10 false Pushed 2.427,1.875 2.583,2.052 0.156,0.177 10 false 1 2.406,2.604 2.563,2.781 0.156,0.177 10 false 3 0.958,1.885 1.115,2.063 0.156,0.177 10 false 2 0.958,2.625 1.115,2.802 0.156,0.177 10 false 4 0.125,0.052 2.615,0.406 2.49,0.354 10 false Component without harness connected: (Stop Light Switch) 0.25,1.76 0.552,1.948 0.302,0.188 10 false Pin

a.

Remove the stop light switch.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Pin not pushed Below 1 Ω
Pin pushed 10 kΩ or higher
3 - 4 Pin not pushed 10 kΩ or higher
Pin pushed Below 1 Ω




OK

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)

NG

REPLACE STOP LIGHT SWITCH

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)
a.

Disconnect the A27 ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
A27-26 (STP) - Body ground Brake pedal is depressed 11 to 14 V
A27-26 (STP) - Body ground Brake pedal is released Below 1 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR