Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM
RM27L0U _51 Engine / Hybrid System _049294 3UR-FE ENGINE CONTROL _0235547 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and sets the DTC.

HINT:

The normal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the Techstream, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.



DTC Code DTC Detection Condition Trouble Area
P0504 Conditions (a), (b) and (c) continue for 0.5 seconds or more
(1 trip detection logic):
(a) Ignition switch ON
(b) Brake pedal released
(c) STP signal OFF when ST1- signal OFF
·

Short in stop light switch signal circuit

·

STOP fuse

·

IGN fuse

·

Stop light switch

·

ECM



WIRING DIAGRAM

A185018E06
6.073,3.083 6.448,3.26 0.375,0.177 10 false ECM 5.677,0.792 6.031,0.958 0.354,0.167 10 false ST1- 5.688,1.563 6,1.719 0.313,0.156 10 false STP 5.396,0.729 5.615,0.885 0.219,0.156 10 false 35 5.344,1.677 5.677,1.844 0.333,0.167 10 false A27 5.344,0.917 5.667,1.073 0.323,0.156 10 false A27 5.406,1.479 5.604,1.646 0.198,0.167 10 false 26 4.198,1.927 4.406,2.094 0.208,0.167 10 false A4 4.188,2.083 5.344,2.281 1.156,0.198 10 false Stop Light Switch 5.094,0.771 5.198,0.938 0.104,0.167 10 false 3 5.094,1.531 5.208,1.698 0.115,0.167 10 false 1 4.292,0.781 4.396,0.948 0.104,0.167 10 false 4 4.292,1.542 4.396,1.708 0.104,0.167 10 false 2 3.646,1.042 3.958,1.208 0.313,0.167 10 false IGN 3.792,1.792 4.208,1.948 0.417,0.156 10 false STOP 2.604,1.823 2.885,1.979 0.281,0.156 10 false IG2 1.854,1.365 2.135,1.521 0.281,0.156 10 false IG2 2.188,1.365 2.292,1.531 0.104,0.167 10 false 6 1.083,1.365 1.188,1.531 0.104,0.167 10 false 5 1.25,1.365 1.573,1.521 0.323,0.156 10 false AM2 1.031,2.344 1.354,2.5 0.323,0.156 10 false AM2 0.479,2.26 0.875,2.594 0.396,0.333 10 false IG2 MAIN 3.698,3.635 3.99,3.792 0.292,0.156 10 false ALT 0.646,4.781 1.135,4.969 0.49,0.188 10 false Battery 1.385,1.906 1.708,2.063 0.323,0.156 10 false H10 1.385,2.063 2.333,2.25 0.948,0.188 10 false Ignition Switch

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

STP signal conditions can be checked using the Techstream.

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the Techstream on.

4.

Enter the following menus: Powertrain / Engine and ECT / All Data / Stop Light Switch.

5.

Check the STP signal when the brake pedal is depressed and released.




Brake Pedal Operation Specified Condition
Depressed STP signal ON
Released STP signal OFF

PROCEDURE

1.CHECK STOP LIGHT SWITCH ASSEMBLY (B+ VOLTAGE)
U151424E02
0.177,0.125 2.521,0.469 2.344,0.344 10 false Front view of wire harness connector: (to Stop Light Switch) 0.865,1.792 1.135,1.969 0.271,0.177 10 false A4

a.

Disconnect the A4 stop light switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
A4-2 - Body ground Always 11 to 14 V
A4-4 - Body ground Ignition switch ON 11 to 14 V




OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

4.INSPECT FUSE (STOP AND IGN)
2.INSPECT STOP LIGHT SWITCH ASSEMBLY
A115657E35
1.927,2.344 2.365,2 false 1.594,2.344 1.135,2 false 1.979,2.563 2.344,2.667 false 1.531,2.563 1.125,2.688 false 0.521,1.792 1.115,1.479 false 0.083,0.813 0.906,0.99 0.823,0.177 10 false Not Pushed 2.094,0.833 2.635,1.031 0.542,0.198 10 false Pushed 2.427,1.875 2.583,2.052 0.156,0.177 10 false 1 2.406,2.604 2.563,2.781 0.156,0.177 10 false 3 0.958,1.885 1.115,2.063 0.156,0.177 10 false 2 0.958,2.625 1.115,2.802 0.156,0.177 10 false 4 0.125,0.052 2.615,0.406 2.49,0.354 10 false Component without harness connected: (Stop Light Switch) 0.25,1.76 0.552,1.948 0.302,0.188 10 false Pin

a.

Remove the stop light switch (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Pin not pushed Below 1 Ω
Pin pushed 10 kΩ or higher
3 - 4 Pin not pushed 10 kΩ or higher
Pin pushed Below 1 Ω




OK

3.CHECK ECM (STP AND ST1 - VOLTAGE)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

3.CHECK ECM (STP AND ST1 - VOLTAGE)
U152962E02
1.948,3.448 2.604,3.292 false 1.781,3.656 1.542,4.219 false 2.188,0.24 2.99,0.552 0.802,0.313 10 false Brake Pedal Released 0.677,0.24 1.448,0.563 0.771,0.323 10 false Brake Pedal Depressed 0.063,1.99 2.417,2.344 2.354,0.354 10 false Front view of wire harness connector: (to ECM) 2.688,3.177 3.042,3.385 0.354,0.208 10 false STP 1.354,4.24 1.729,4.438 0.375,0.198 10 false ST1- 0.25,2.99 0.552,3.156 0.302,0.167 10 false A27

a.

Disconnect the A27 ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
A27-35 (ST1-) - Body ground Brake pedal released 11 to 14 V
Brake pedal depressed 0 to 3 V
A27-26 (STP) - Body ground Brake pedal released 0 to 3 V
Brake pedal depressed 11 to 14 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FUSE (STOP AND IGN)
A162281E01
0.057,0.027 1.764,0.197 1.707,0.170 10 Engine Room Relay Block: 2.819,2.837 3.113,2.993 0.295,0.156 10 IGN 1.037,2.854 1.457,3.010 0.420,0.156 10 STOP 1.209,2.803 1.406,1.662 false 2.922,2.826 2.681,2.009 false

a.

Remove the STOP and IGN fuses from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
STOP fuse Always Below 1 Ω
IGN fuse Always Below 1 Ω




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - STOP LIGHT SWITCH)

NG

CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE