Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM
RM27L0U _51 Engine / Hybrid System _049294 3UR-FE ENGINE CONTROL _0235547 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P0607  Control Module Performance  


DESCRIPTION

The ECM continuously monitors its internal processors (CPUs) and heated oxygen sensor (HO2S) transistors. This self-check ensures that the ECM is functioning properly.

DTC Code DTC Detection Condition Trouble Area
P0607
·

ECM CPUs malfunction

·

HO2S transistors malfunction


·

Exhaust gas leak

·

HO2S

·

ECM



NOTICE:

An exhaust gas leak generates noise in the HO2S output. The ECM may interpret this as an HO2S transistor malfunction and set P0607.


MONITOR STRATEGY

Related DTCs P0607: Control module performance
Required Sensors/Components (Main) ECM
Required Sensors/Components (Related) HO2S
Frequency of operation Continuous
Duration 60 seconds
MIL operation Immediate
Sequence of operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever the following DTCs are not present None
Engine Running
Estimated HO2S temperature 450 to 750°C (842 to 1382°F)

TYPICAL MALFUNCTION THRESHOLDS

HO2S transistors Fail

CONFIRMATION DRIVING PATTERN

A212371E04
5.227,2.932 5.912,3.311 0.685,0.378 10 5 minutes or more 6.226,3.402 6.423,3.584 0.196,0.183 10 [I] 1.716,2.28 1.944,2.447 0.228,0.167 10 [B] 2.031,2.281 2.258,2.448 0.228,0.167 10 [C] 2.382,2.036 2.640,2.219 0.257,0.184 10 [D] 2.829,2.034 3.026,2.245 0.196,0.211 10 [E] 3.272,2.033 3.476,2.244 0.205,0.211 10 [F] 0.647,2.129 1.057,2.299 0.411,0.170 10 Idling 1.829,3.302 2.485,3.485 0.656,0.184 10 2 minutes 4.03,0.982 4.248,1.193 0.218,0.211 10 [G] 5.447,0.985 5.665,1.196 0.218,0.211 10 [H] 3.122,2.955 3.688,3.139 0.566,0.184 10 1 minute 2.456,2.856 2.092,3.287 false 0.706,2.955 2.236,3.130 1.530,0.174 10 30 minutes or more 1.358,2.556 1.570,2.795 0.211,0.239 10 [A] 0.351,0.681 1.025,1.029 0.674,0.348 10 80 km/h (50 mph) 0.362,1.395 0.990,1.754 0.628,0.360 10 56 km/h (35 mph) 0.147,2.399 1.136,2.731 0.989,0.332 10 Ignition Switch ON

1.

Stop the engine for 30 minutes or more [A].

2.

Connect the Techstream to the DLC3.

3.

Turn the ignition switch to ON and turn the Techstream on.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) [B].

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the Techstream on [C].

7.

Start the engine, and wait 2 minutes [D].

8.

Warm up the engine until the engine coolant temperature is 75°C (167°F) or more [E].

9.

Idle the engine for 1 minute [F].

10.

Accelerate the vehicle to 80 km/h (50 mph) and stop the vehicle [G].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


11.

Drive the vehicle at 56 to 80 km/h (35 to 50 mph) for 5 minutes or more [H].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


12.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [I].

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

15.

Input the DTC: P0607, P0136, P0137, P0138, P0156, P0157 or P0158.

16.

Check the DTC judgment result.

Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [I].



17.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menu: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTC (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
P0607 and P0136, P0137, P0138, P0156, P0157 or P0158 are output A
P0607 is output B



A

2.INSPECT DTC (P0136, P0137, P0138, P0156, P0157 OR P0158)

B

3.CHECK FOR EXHAUST GAS LEAK
2.INSPECT DTC (P0136, P0137, P0138, P0156, P0157 OR P0158)
a.

Inspect the P0136, P0137, P0138, P0156, P0157 or P0158 flowchart.

HINT:
·

If P0136 or P0156 is output, troubleshoot for that DTC first (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>P0136). Then proceed to "INSPECT ECM".

·

If P0137 or P0157 is output, troubleshoot for that DTC first (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>P0136). Then proceed to "INSPECT ECM".

·

If P0138 or P0158 is output, troubleshoot for that DTC first (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>P0136). Then proceed to "INSPECT ECM".

·

If DTC P0607 and P0136, P0137, P0138, P0156, P0157 or P0158 are output, the output voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or more).





NEXT

6.INSPECT ECM
3.CHECK FOR EXHAUST GAS LEAK
a.

Allow the engine to idle and rev the engine.


b.

Check for exhaust gas leaks around the heated oxygen sensor.

If any exhaust gas leaks are present, repair it and proceed to "PERFORM CONFIRMATION DRIVING PATTERN". If no exhaust gas leaks are present proceed to "PERFORM CONFIRMATION DRIVING PATTERN".

HINT:
·

If no exhaust gas leaks are present, a malfunction in the heated oxygen sensor circuit is suspected.

·

If any exhaust gas leaks are present around the heated oxygen sensor, noise appears in the output voltage of the heated oxygen sensor.

·

Perform "Inspection After Repair" after repairing or replacing the exhaust system (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).





NEXT

4.PERFORM CONFIRMATION DRIVING PATTERN
4.PERFORM CONFIRMATION DRIVING PATTERN
A144392E23
0.03,0.27 3.255,0.433 3.225,0.163 10 Engine Coolant Temperature: 75°C (167°F) or more 1.555,0.914 2.044,1.091 0.489,0.177 10 80 (50) 1.555,1.299 2.044,1.482 0.489,0.184 10 60 (35) 1.295,0.62 2.034,0.804 0.739,0.184 10 km/h (mph) 1.922,2.453 2.036,2.609 0.114,0.156 10 0 6.361,2.442 6.721,2.597 0.361,0.156 10 Time 4.546,0.858 5.188,1.014 0.642,0.156 10 5 minutes 4.081,1.189 4.081,0.828 false 5.656,1.189 5.656,0.828 false 4.511,0.914 4.081,0.914 false 5.192,0.914 5.656,0.914 false


b.

Connect the Techstream to the DLC3.


c.

Start the engine.


d.

Warm up the engine until the engine coolant temperature becomes 75°C (167°F) or more.


e.

Perform the drive pattern.

i.

Accelerate the vehicle to 80 km/h (50 mph) and stop the vehicle.


ii.

Drive the vehicle between 60 and 80 km/h (35 and 50 mph) for 5 minutes.



f.

Enter the following menu: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTCs.

Result
Result Proceed to
P0607 and P0136, P0137, P0138, P0156, P0157 or P0158 are output A
Only P0607 B
No DTC output C



A

5.INSPECT DTC (P0136, P0137, P0138, P0156, P0157 OR P0158)

B

C

6.INSPECT ECM
5.INSPECT DTC (P0136, P0137, P0138, P0156, P0157 OR P0158)
a.

Inspect the P0136, P0137, P0138, P0156, P0157 or P0158 flowchart.

HINT:
·

If P0136 or P0156 is output, troubleshoot for that DTC first (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>P0136). Then proceed to "INSPECT ECM".

·

If P0137 or P0157 is output, troubleshoot for that DTC first (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>P0136). Then proceed to "INSPECT ECM".

·

If P0138 or P0158 is output, troubleshoot for that DTC first (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>P0136). Then proceed to "INSPECT ECM".

·

If DTC P0607 and P0136, P0137, P0138, P0156, P0157 or P0158 are output, the output voltage of the heated oxygen sensor may remain close to 0 V or become high (around 1 V or more).





NEXT

6.INSPECT ECM
6.INSPECT ECM

b.

Stop the engine and wait for 30 minutes.


c.

Connect the Techstream to the DLC3.


d.

Start the engine and allow it to idle for 2 minutes.


e.

Turn the Techstream on.


f.

Enter the following menu: Powertrain / Engine and ECT / Trouble Codes.


g.

Check the DTCs.

Result
Result Proceed to
DTC is not output A
P0607 is output B



A

END

B