While the engine is being cranked, the positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and sets the DTC.
This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0617 | When conditions (a), (b) and (c) met, positive (+B) battery voltage 10.5 V or more applied to ECM for 20 seconds (1 trip detection logic)
(a) Vehicle speed 20 km/h (12.4 mph) or more (b) Engine speed 1000 rpm or more (c) STA signal ON |
·
Park / Neutral Position (PNP) switch ·
Starter relay circuit ·
Ignition switch ·
ECM |
| Related DTCs | P0617: Starter signal |
| Required Sensors/Components (Main) | ST relay, PNP switch and Ignition switch |
| Required Sensors/Components (Related) | Vehicle Speed Sensor (VSS), Crankshaft Position (CKP) sensor |
| Frequency of Operation | Continuous |
| Duration | 20 seconds |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Battery voltage | 10.5 V or more |
| Vehicle speed | 20 km/h (12.4 mph) or more |
| Engine speed | 1000 rpm or more |
| Starter signal | ON |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on [A].
Idle the engine for 5 seconds or more [B].
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
Read the Pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0617.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit |
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].
Drive the vehicle at 24 km/h (15 mph) or more for 20 seconds or more [D].
Check the DTC judgment result [E].
If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
The following troubleshooting flowchart is based on the premise that the engine is cranked normally.
If the engine will not crank, proceed to the problem symptoms table (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>PROBLEM SYMPTOMS TABLE).
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.
Check the value displayed on the Techstream when the ignition switch is turned to the ON and START positions.
| Ignition Switch Position | Starter Signal |
|---|---|
| ON | OFF |
| START | ON |
OK
NG
Disconnect the D21 PNP switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (B) - 5 (L) | Shift lever position P | Below 1 Ω |
| Shift lever position N | Below 1 Ω | |
| Shift lever position not on P or N | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Replace the park / neutral position switch.
NEXT
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.
Check the value displayed on the Techstream when the ignition switch is turned to the ON and START positions.
| Ignition Switch Position | Starter Signal |
|---|---|
| ON | OFF |
| START | ON |
OK
NG
Disconnect the H10 ignition switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 5 (AM2) - 7 (ST2) | Ignition switch position LOCK | 10 kΩ or higher |
| Ignition switch position START | Below 1 Ω |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Replace the ignition switch (See page Engine / Hybrid System>3UR-FE STARTING>IGNITION SWITCH>REMOVAL).
NEXT
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.
Check the value displayed on the Techstream when the ignition switch is turned to the ON and START positions.
| Ignition Switch Position | Starter Signal |
|---|---|
| ON | OFF |
| START | ON |
OK
NG
NEXT
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Drive the vehicle at more than 20 km/h (12.4 mph) for over 20 seconds.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
|---|---|
| P0617 is output | A |
| No DTC is output | B |
A
B