Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM
RM27L0U _51 Engine / Hybrid System _049294 3UR-FE ENGINE CONTROL _0235547 SFI SYSTEM U

3UR-FE ENGINE CONTROL  SFI SYSTEM  FAIL-SAFE CHART  


If any of the following DTCs are set, the ECM enters fail-safe mode to allow the vehicle to be driven temporarily.

DTC Component Fail-Safe Operation Fail-Safe Deactivation Condition
P0011, P0021, P0015 and P0025 VVT system
·

Idle up (Control of combustion worsening)

·

Stopping fuel-cut control


Pass condition detected
P0031, P0032, P0051 and P0052 Air-Fuel Ratio (A/F) Sensor Heater ECM turns off A/F sensor heater. Ignition switch off
P0037, P0038, P0057 and P0058 Heated Oxygen (HO2) Sensor Heater ECM turns off HO2 sensor heater. Ignition switch off
P0102 and P0103 Mass Air Flow (MAF) Meter ECM calculates ignition timing according to engine speed and throttle valve position. Pass condition detected
P0112 and P0113 Intake Air Temperature (IAT) Sensor ECM estimates IAT to be 20°C (68°F). Pass condition detected
P0115, P0117 and P0118 Engine Coolant Temperature (ECT) Sensor ECM estimates ECT to be 80°C (176°F). Pass condition detected
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0604, P0606, P060A, P060B, P060D, P060E, P0657, P2102, P2103, P2111, P2112, P2118, P2119 and P2135 Electronic Throttle Control System (ETCS) ECM cuts off throttle actuator current and throttle valve returned to 7° throttle position by return spring.
ECM then adjusts engine output by controlling fuel injection (intermittent fuel-cut) and ignition timing in accordance with accelerator pedal opening angle to allow vehicle to continue at minimal speed*1.
Pass condition detected and then ignition switch turned off
P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and P0308*2
·

Fuel injector

·

Electronic Throttle Control System (ETCS)


When misfire occurs, fuel cut is performed for catalyst overheat malfunction prevention
·

During normal load and normal engine speed (MIL is blinking)

·

Fuel cut is performed on malfunctioning cylinder


·

During high load and high engine speed (MIL is blinking)

·

Throttle valve opening angle control is performed

·

All cylinder fuel cut or malfunction cylinder fuel cut



Pass condition detected and then ignition switch turned off
P0327, P0328, P0332 and P0333 Knock Sensor ECM sets ignition timing to maximum retard. Ignition switch off
P0351 to P0358 Igniter ECM cuts fuel. Pass condition detected
P0504 Stop Light Switch The accelerator pedal opening angle is fixed when there is an accelerator pedal malfunction or history of a malfunction. Accelerator pedal angle is fixed
P2120, P2121, P2122, P2123, P2125, P2127, P2128 and P2138 Accelerator Pedal Position (APP) Sensor The APP sensor has 2 sensor circuits: Main and Sub.
If either circuit malfunctions, the ECM limits the engine output.
If both circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.
Pass condition detected and then ignition switch turned off
P2432, P2433, P2437 and P2438 Secondary Air Injection System Throttle valve opening angle control is performed Pass condition detected
P2440 and P2442 Secondary Air Injection System Throttle valve opening angle control is performed Pass condition detected
P2445 and P2447 Secondary Air Injection System Throttle valve opening angle control is performed Pass condition detected

HINT:
·

*1: The vehicle can be driven slowly when the accelerator pedal is depressed firmly and slowly. If the accelerator pedal is depressed quickly, the vehicle may speed up and slow down erratically.

·

*2: Misfire related fail-safe operations occur when catalyst overheat malfunctions occur.