The power steering oil pressure sensor is turned ON when a power steering wheel load occurs by turning the steering wheel. The ECM regulates the engine idling RPM according to the voltage output of the sensor.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0550 | Power steering oil pressure sensor voltage less than 0.28 V, or more than 4.9 V for 0.5 seconds while engine running.
(1 trip detection logic) |
·
Open or short in power steering oil pressure sensor circuit ·
Power steering oil pressure sensor ·
ECM |
| P0552 | Power steering oil pressure sensor voltage less than 0.28 V for 0.5 seconds while engine running.
(1 trip detection logic) |
·
Open or short in power steering oil pressure sensor circuit ·
Power steering oil pressure sensor ·
ECM |
| P0553 | Power steering oil pressure sensor voltage more than 4.9 V for 0.5 seconds while engine running.
(1 trip detection logic) |
·
Open or short in power steering oil pressure sensor circuit ·
Power steering oil pressure sensor ·
ECM |
The ECM monitors the sensor voltage and uses this value to regulate the engine idling speed. When the sensor output voltage deviates from the normal operating range, the ECM determines that there is a malfunction in the power steering oil pressure sensor and sets a DTC.
| Related DTCs | P0550: Power steering pressure sensor range check (Chattering)
P0552: Power steering pressure sensor range check (Low Resistance) P0553: Power steering pressure sensor range check (High Resistance) |
| Required Sensors/Components | Power steering pressure sensor |
| Frequency of operation | Continuous |
| Duration | 0.5 seconds |
| MIL operation | Immediate |
| Sequence of operation | None |
| Monitor runs whenever following DTCs not present | None |
| Time after starter signal ON to OFF | 2 seconds or more |
| Power steering pressure sensor voltage | Less than 0.28 V, or more than 4.9 V |
| Power steering pressure sensor voltage | Less than 0.28 V |
| Power steering pressure sensor voltage | More than 4.9 V |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on [A].
Start the engine.
Idle the engine for 5 seconds [B].
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
Read the Pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0550, P0552 or P0553.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.
If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Disconnect the D56 ECM connector.
Disconnect the D30 power steering oil pressure sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D30-2 (PSP) - D56-72 (PSP) | Always | Below 1 Ω |
| D30-1 (VC) - D56-67 (VCV1) | Always | Below 1 Ω |
| D30-3 (E2) - D56-97 (ETHW) | Always | Below 1 Ω |
| D30-2 (PSP) or D56-72 (PSP) - Body ground | Always | 10 kΩ or higher |
| D30-1 (VC) or D56-67 (VCV1) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the power steering oil pressure sensor.
NEXT
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P0550, P0552 and/or P0553 are output | A |
| No DTC is output | B |
A
B