Home › Engine / Hybrid System › 3UR-FBE ENGINE MECHANICAL › CYLINDER HEAD › 2015.08–2016.10
RM27L0U _51 Engine / Hybrid System _049295 3UR-FBE ENGINE MECHANICAL _0235556 CYLINDER HEAD A

3UR-FBE ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 11122 1.REPLACE INTAKE VALVE GUIDE BUSH

NOTICE:
A384519N01
2.927,1.292 3.188,1.531 0.26,0.24 10 true (A)

The standard protrusion amount (A) of the valve guide bush determines whether the cylinder head is type A or B. Therefore, measure the standard protrusion amount (A) before removing the valve guide bush.


Standard Protrusion Height (A):
Type Specified Condition
Cylinder Head Type A 14.3 to 14.7 mm (0.563 to 0.579 in.)
Cylinder Head Type B 15.8 to 16.2 mm (0.622 to 0.638 in.)


a.

Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).


b.

Place the cylinder head on wooden blocks.


c.
A164331E02
2.062,0.042 2.429,0.213 0.367,0.171 10 SST 1.532,0.712 1.921,0.131 1.921,0.131 2.035,0.131 false 1.921,0.131 1.598,1.161 false

Using SST and a hammer, tap out the valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.
A145564

Using a caliper gauge, measure the bush bore diameter of the cylinder head side.

Standard cylinder bore diameter:

10.285 to 10.306 mm (0.405 to 0.406 in.)


If the bush bore diameter of the cylinder head is between 10.285 to 10.306 mm (0.405 to 0.406 in.), proceed to the next step.

If the bush bore diameter of the cylinder head is 10.356 mm (0.408 in.) or more, replace the cylinder head.


e.

Select a new guide bush (STD or O/S 0.05), and measure its diameter.


f.

Machine the bush bore diameter of the cylinder head side to the diameter of the selected guide bush.

Bush Bore Diameter:
Bush Size Specified Condition
STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)


Standard bush length:

41.3 to 41.7 mm (1.63 to 1.64 in.)



g.
A164332E15
1.521,0.677 1.844,0.135 1.844,0.135 1.583,1.115 true 1.885,0.052 2.24,0.219 0.354,0.167 10 false SST 2.979,1.271 3.26,1.521 0.281,0.25 10 true (A)

Using SST and a hammer, tap in a new guide bush to the standard protrusion height (A).

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard Protrusion Height (A):
Type Specified Condition
Cylinder Head Type A 14.3 to 14.7 mm (0.563 to 0.579 in.)
Cylinder Head Type B 15.8 to 16.2 mm (0.622 to 0.638 in.)


NOTICE:

Install the valve guide bush after determining cylinder head type A and B.



h.
A164333

Using a sharp 5.5 mm reamer, ream the guide bush to obtain the standard oil clearance between the guide bush and valve stem.

Standard oil clearance:

0.025 to 0.060 mm (0.000984 to 0.00236 in.)



Hide 11126 2.REPLACE EXHAUST VALVE GUIDE BUSH

NOTICE:
A384519N01
2.927,1.292 3.188,1.531 0.26,0.24 10 true (A)

The standard protrusion amount (A) of the valve guide bush determines whether the cylinder head is type A or B. Therefore, measure the standard protrusion amount (A) before removing the valve guide bush.


Standard Protrusion Height (A):
Type Specified Condition
Cylinder Head Type A 14.3 to 14.7 mm (0.563 to 0.579 in.)
Cylinder Head Type B 15.8 to 16.2 mm (0.622 to 0.638 in.)


a.

Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).


b.

Place the cylinder head on wooden blocks.


c.
A164334E02
3,1.555 3.315,1.729 0.316,0.174 10 SST 1.992,1.29 2.829,1.642 2.829,1.642 2.965,1.642 false 2.064,0.727 2.829,1.642 false

Using SST and a hammer, tap out the valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.
A145566

Using a caliper gauge, measure the bush bore diameter of the cylinder head.

Standard cylinder bore diameter:

10.285 to 10.306 mm (0.405 to 0.406 in.)


If the bush diameter of the cylinder head is between 10.285 to 10.306 mm (0.405 to 0.406 in.), proceed to the next step.

If the bush bore diameter of the cylinder head is 10.356 mm (0.408 in.) or more, replace the cylinder head.


e.

Select a new guide bush (STD or O/S 0.05), and measure its diameter.


f.

Machine the bush bore diameter of the cylinder head side to the diameter of the selected guide bush.

Bush Bore Diameter:
Bush Size Specified Condition
STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)


Standard bush length:

46.8 to 47.2 mm (1.84 to 1.86 in.)



g.
A164335E15
2.031,1.063 2.948,1.521 2.948,1.521 2,1.302 true 3,1.438 3.313,1.594 0.313,0.156 10 false SST 0.177,1.313 0.427,1.573 0.25,0.26 10 true (A)

Using SST and a hammer, tap in a new guide bush to the standard protrusion height (A).

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard Protrusion Height (A):
Type Specified Condition
Cylinder Head Type A 14.3 to 14.7 mm (0.563 to 0.579 in.)
Cylinder Head Type B 15.8 to 16.2 mm (0.622 to 0.638 in.)


NOTICE:

Install the valve guide bush after determining cylinder head type A and B.



h.
A164336

Using a sharp 5.5 mm reamer, ream the guide bush to obtain the standard oil clearance between the guide bush and valve stem.

Standard oil clearance:

0.030 to 0.065 mm (0.00118 to 0.00256 in.)



Hide 11115A 3.REPLACE RING PIN

NOTICE:

It is not necessary to remove the ring pin unless it is being replaced.


a.

Remove the ring pins.


b.

Using a plastic-faced hammer, tap in new ring pins to the cylinder head.

A145571E08
0.604,0.104 0.927,0.313 0.323,0.208 10 false LH: 3.74,0.083 4.135,0.292 0.396,0.208 10 false RH: 2.396,2.094 3.292,2.26 0.896,0.167 10 false 5.5 to 6.5 mm 4.406,2.052 5.302,2.219 0.896,0.167 10 false 3.5 to 6.5 mm 6.219,1.031 6.333,1.188 0.115,0.156 10 false A 3.865,2.49 4.01,2.635 0.146,0.146 10 false B 1.885,2.479 2,2.635 0.115,0.156 10 false A 3.865,1.354 4.01,1.5 0.146,0.146 10 false B 3.938,1 4.052,1.156 0.115,0.156 10 false A 0.792,0.458 0.938,0.604 0.146,0.146 10 false B 3.052,1.115 3.167,1.271 0.115,0.156 10 false A 0.813,1.125 0.927,1.281 0.115,0.156 10 false A

Standard Protrusion:
Item Specified Condition
Ring pin A 5.5 to 6.5 mm (0.217 to 0.256 in.)
Ring pin B 3.5 to 6.5 mm (0.138 to 0.256 in.)