Home › Engine / Hybrid System › 3UR-FBE ENGINE MECHANICAL › CYLINDER HEAD › 2015.08–2016.10
RM27L0U _51 Engine / Hybrid System _049295 3UR-FBE ENGINE MECHANICAL _0235556 CYLINDER HEAD A

3UR-FBE ENGINE MECHANICAL  CYLINDER HEAD  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

There are two cylinder head assembly shapes. Valve spring type A can only be used with cylinder head type A and valve spring type B can only be used with cylinder head type B. The combination cannot be changed.


HINT:
·
A384519N02
2.927,1.292 3.188,1.531 0.26,0.24 10 true (A)

The standard protrusion amount (A) of the valve guide bush determines whether the cylinder head is type A or B.

Standard Protrusion Height (A)
Type Specified Condition
Cylinder Head Type A 14.3 to 14.7 mm (0.563 to 0.579 in.)
Cylinder Head Type B 15.8 to 16.2 mm (0.622 to 0.638 in.)

·
A384520C02
1.781,0.021 3.396,4.427 1.615,4.406 0.021,0.021 1.719,4.427 1.698,4.406 1.229,1.677 1.396,1.677 false 2.958,1.677 3.125,1.677 false 0.927,2.552 1.344,2.552 false 2.625,2.552 3.042,2.552 false 0.958,3.833 1.323,3.833 false 2.646,3.865 3.01,3.865 false 0.052,0.052 0.271,0.26 0.219,0.208 10 false *A 1.813,0.042 2.052,0.24 0.24,0.198 10 false *B 1.448,1.604 1.656,1.781 0.208,0.177 10 false *1 1.375,2.479 1.594,2.677 0.219,0.198 10 false *2 1.354,3.76 1.573,3.969 0.219,0.208 10 false *3 0.656,2.094 0.865,2.292 0.208,0.198 10 false *a 1.396,0.594 1.594,0.792 0.198,0.198 10 false *b 2.354,2.094 2.563,2.292 0.208,0.198 10 false *a 3.115,0.594 3.313,0.792 0.198,0.198 10 false *b 3.052,3.792 3.271,4 0.219,0.208 10 false *3 3.083,2.469 3.302,2.667 0.219,0.198 10 false *2 3.167,1.604 3.375,1.781 0.208,0.177 10 false *1
*A Valve Spring Type A
*B Valve Spring Type B
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Spring Retainer
*3 Inner Compression Spring
*a Valve Spring Retainer Outer Diameter
*b No. 1 Valve Rocker Arm Roller Width


The shape of the inner compression spring determines whether the valve spring type is A or B.

·

The No. 1 valve rocker arm, inner compression spring and valve spring retainer have two different shapes and are not interchangeable.

Valve Spring Type No. 1 Valve Rocker Arm Roller Width Valve Spring Retainer Outer Diameter Inner Compression Spring Shape
A 10.7 mm (0.421 in.) 23.4 mm (0.921 in.) Straight
B 8.0 mm (0.315 in.) 18.9 mm (0.744 in.) Taper



PROCEDURE

Hide 1.INSTALL STUD BOLT

a.

Using E7 and E8 "TORX" socket wrenches, install the stud bolts.

·

Stud bolts A, B, C, D


Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

U151459E02
4.906,3.906 4.698,3.729 4.698,3.729 4.604,3.729 false 0.802,0.917 0.802,1.333 true 6.615,0.99 6.615,1.396 true 1.802,2.969 1.802,3.073 false 1.104,2.75 1.104,2.958 false 1.365,2.448 1.365,2.948 false 1.667,2.76 1.667,2.948 false 1.927,2.771 1.927,2.958 false 2.25,2.458 2.25,2.958 false 2.5,2.458 2.5,2.958 false 5.458,2.969 5.458,3.063 false 4.76,2.74 4.76,2.948 false 5.021,2.448 5.021,2.948 false 5.323,2.76 5.323,2.948 false 5.583,2.448 5.583,2.948 false 5.875,2.76 5.875,2.958 false 6.146,2.76 6.146,2.958 false 2.667,4.01 2.781,4.01 2.781,4.01 2.781,4.281 false 2.563,4.292 3,4.292 false 4.802,3.99 4.688,3.99 4.688,3.99 4.688,4.26 false 4.906,4.271 4.458,4.271 false 0.885,6.292 1.219,6.438 1.219,6.438 1.219,6.542 false 0.885,5.49 1.083,5.188 1.083,5.188 1.146,5.188 false 2.479,6.302 2.781,6.469 2.781,6.469 2.781,6.563 false 2.771,5.24 2.677,5.24 2.677,5.24 2.469,5.677 false 4.146,6.229 4.417,6.406 4.417,6.406 4.417,6.469 false 4.365,5.469 4.292,5.469 4.292,5.469 4.125,5.896 false 5.625,6.302 5.781,6.448 5.781,6.448 5.781,6.542 false 5.615,5.948 5.802,5.594 5.802,5.594 5.885,5.594 false 0.448,0.052 2.563,0.24 2.115,0.188 10 false Intake Manifold Side of RH: 4.146,0.042 5.969,0.271 1.823,0.229 10 false Intake Manifold Side of LH: 4.146,1.677 6.396,1.885 2.25,0.208 10 false Exhaust Manifold Side of LH: 0.448,1.688 2.479,1.896 2.031,0.208 10 false Exhaust Manifold Side of RH: 0.448,3.323 1.844,3.531 1.396,0.208 10 false Front Side of RH: 4.146,3.313 5.479,3.521 1.333,0.208 10 false Front Side of LH: 1.177,5.104 2.313,5.292 1.135,0.188 10 false 12 mm (0.472 in.) 1.406,5.688 2.083,6.052 0.677,0.365 10 false 52 mm (2.05 in.) 2.448,6.552 3.604,6.76 1.156,0.208 10 false 13 mm (0.512 in.) 2.823,5.167 4.375,5.323 1.552,0.156 10 false 24 mm (0.945 in.) 2.938,5.771 3.594,6.135 0.656,0.365 10 false 45 mm (1.77 in.) 4.417,5.385 5.552,5.542 1.135,0.156 10 false 20 mm (0.787 in.) 5.927,5.51 7.083,5.667 1.156,0.156 10 false 14 mm (0.551 in.) 4.573,5.854 5.24,6.229 0.667,0.375 10 false 35 mm (1.38 in.) 6.104,5.844 6.792,6.208 0.688,0.365 10 false 29 mm (1.14 in.) 0.583,6.552 0.74,6.719 0.156,0.167 10 false A 4.458,3.646 4.615,3.813 0.156,0.167 10 false A 2.188,6.552 2.323,6.729 0.135,0.177 10 false B 1.75,3.104 1.885,3.281 0.135,0.177 10 false C 5.417,3.073 5.552,3.25 0.135,0.177 10 false C 3.823,6.542 3.969,6.74 0.146,0.198 10 false C 0.76,1.365 0.906,1.563 0.146,0.198 10 false B 6.583,1.406 6.729,1.604 0.146,0.198 10 false B 5.302,6.552 5.438,6.698 0.135,0.146 10 false D 4.354,4.146 4.49,4.292 0.135,0.146 10 false D 3.031,4.156 3.167,4.302 0.135,0.146 10 false D 0.896,6.563 2.031,6.75 1.135,0.188 10 false 12 mm (0.472 in.) 4.104,6.542 5.26,6.75 1.156,0.208 10 false 13 mm (0.512 in.) 5.448,6.542 6.604,6.75 1.156,0.208 10 false 13 mm (0.512 in.)


Hide 11117F 2.INSTALL NO. 2 STRAIGHT SCREW PLUG

a.
A164330E01
0.064,0.065 0.358,0.276 0.295,0.211 10 RH: 0.064,2.402 0.352,2.572 0.288,0.170 10 LH:

Using a 14 mm hexagon wrench, install 2 new gaskets and the 2 straight screw plugs.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)


Hide 11117E 3.INSTALL NO. 1 STRAIGHT SCREW PLUG

a.
A145550E03
0.077,2.27 0.342,2.452 0.265,0.181 10 LH: 0.077,0 0.388,0.174 0.311,0.174 10 RH:

Using a 10 mm hexagon wrench, install 6 new gaskets and the 6 straight screw plugs.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 13734 4.INSTALL VALVE SPRING SEAT

a.

Install the valve spring seats to the cylinder head.


Hide 13711E 5.INSTALL VALVE STEM OIL SEAL

a.

Apply a light coat of engine oil to new oil seals.

A321194E02
1.94,1.178 2.791,1.422 0.850,0.244 10 Black 5.17,1.165 6.020,1.409 0.850,0.244 10 Gray 1.328,0.656 1.468,0.516 false 2.432,0.786 2.189,1.166 false 4.974,0.478 4.706,0.591 false 5.756,1.067 5.518,1.214 false 0.322,0.179 3.442,1.524 3.12,1.345 3.765,0.179 6.885,1.524 3.12,1.345 0.42,0.24 1.271,0.484 0.850,0.244 10 Intake Side 3.862,0.24 4.810,0.484 0.948,0.244 10 Exhaust Side 1.522,0.429 2.373,0.673 0.850,0.244 10 Gray 5.032,0.394 5.882,0.638 0.850,0.244 10 Black

NOTICE:

Pay attention when installing the intake and exhaust oil seals. For example, installing the intake oil seal into the exhaust side or installing the exhaust oil seal into the intake side can cause installation problems later.


HINT:
·

for Intake Side

The intake side valve stem oil seals is gray or black.

·

for Exhaust Side

The exhaust side valve stem oil seals is black or gray.




b.
A165065E02
0.169,1.517 0.513,1.702 0.344,0.185 10 SST 0.57,1.599 0.822,1.599 0.822,1.599 1.571,1.128 false 0.588,2.223 1.334,2.386 0.746,0.163 10 CORRECT 1.993,2.212 2.848,2.401 0.855,0.188 10 INCORRECT

Using SST, push in the oil seals.

SST
09201-41020  

NOTICE:

Failure to use SST will cause the seal to be damaged or improperly seated.



Hide 13711 6.INSTALL INTAKE VALVE

HINT:

The shape of the inner compression spring determines whether the valve spring type described here is A or B.


a.
A380012E01
1.708,1.698 3.271,1.896 1.563,0.198 10 false 40 mm (1.57 in.) or more

Apply plenty of engine oil to the tip area of the intake valve shown in the illustration.


b.
A366793C03
0.51,0.385 0.781,0.635 0.271,0.25 10 false *a 0.531,1.552 0.781,1.781 0.25,0.229 10 false *b 0.115,0.146 0.427,0.344 0.313,0.198 10 false *A
*A Valve Spring Type B
*a Narrow
*b Wide


Install the valve, compression spring and spring retainer to the cylinder head.

NOTICE:
·

Install the same parts in the same combination to their original locations.

·

Valve Spring Type B:

Install the inner compression spring to the wide end of the cylinder head sub-assembly.




c.
A164326E01
1.747,0.001 2.058,0.173 0.311,0.172 10 SST 1.885,0.375 2.196,0.547 0.311,0.172 10 SST 2.733,0.456 2.257,0.456 false 1.521,0.538 1.605,0.084 1.605,0.084 1.708,0.084 false

Valve Spring Type A:

i.

Using SST and wooden blocks, compress the spring and install the retainer locks.

SST
09202-70020  (09202-00010, 09202-01010, 09202-01020)


ii.
A165066

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:
·

Do not damage the valve stem tip.

·

Be careful not to damage the retainer.





d.
A366791E01
2.917,0.323 3.01,0.323 false 0.438,0.656 0.563,0.656 0.563,0.656 0.667,0.844 true 0.094,0.573 0.448,0.771 0.354,0.198 10 false SST 3.063,0.229 3.417,0.427 0.354,0.198 10 true SST

Valve Spring Type B:

i.

Using SST and wooden blocks, compress the spring and install the retainer locks.

SST
09202-70020  (09202-01010, 09202-01020)
09202-00021  


ii.
A366795

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:
·

Do not damage the valve stem tip.

·

Be careful not to damage the retainer.





Hide 13715 7.INSTALL EXHAUST VALVE

HINT:

The shape of the inner compression spring determines whether the valve spring type described here is A or B.


a.
A380012E01
1.708,1.698 3.271,1.896 1.563,0.198 10 false 40 mm (1.57 in.) or more

Apply plenty of engine oil to the tip area of the exhaust valve shown in the illustration.


b.
A366794C04
0.698,0.323 0.948,0.573 0.25,0.25 10 false *a 0.698,1.5 0.948,1.729 0.25,0.229 10 false *b 0.135,0.156 0.406,0.438 0.271,0.281 10 false *A
*A Valve Spring Type B
*a Narrow
*b Wide


Install the valve, compression spring and spring retainer to the cylinder head.

NOTICE:
·

Install the same parts in the same combination to their original locations.

·

Valve Spring Type B:

Install the inner compression spring to the wide end of the cylinder head sub-assembly.




c.
A164327E01
1.244,0.012 1.559,0.176 0.316,0.164 10 SST 2.807,1.838 3.122,2.002 0.316,0.164 10 SST 2.967,1.532 2.967,1.813 false 0.765,0.318 1.136,0.096 1.136,0.096 1.218,0.096 false

Valve Spring Type A:

i.

Using SST and wooden blocks, compress the spring and install the retainer locks.

SST
09202-70020  (09202-00010, 09202-01010, 09202-01020)


ii.
A165067

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:
·

Do not damage the valve stem tip.

·

Be careful not to damage the retainer.





d.
A366792E01
0.417,0.271 0.542,0.271 false 2.99,1.698 2.885,1.698 2.885,1.698 2.792,1.594 true 0.104,0.188 0.438,0.396 0.333,0.208 10 false SST 3.031,1.615 3.365,1.823 0.333,0.208 10 false SST

Valve Spring Type B:

i.

Using SST and wooden blocks, compress the spring and install the retainer locks.

SST
09202-70020  (09202-01010, 09202-01020)
09202-00021  


ii.
A366796

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:
·

Do not damage the valve stem tip.

·

Be careful not to damage the retainer.