Home › Engine / Hybrid System › 3UR-FE FUEL › FUEL SYSTEM
RM27L0U _51 Engine / Hybrid System _049298 3UR-FE FUEL _0235579 FUEL SYSTEM L

3UR-FE FUEL  FUEL SYSTEM  PRECAUTION  


CAUTION:
·

Before working on the fuel system, disconnect the cable from the negative (-) battery terminal.

·

Do not smoke or be near an open flame when working on the fuel system.

·

Keep gasoline away from rubber and leather parts.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


DISCHARGE FUEL SYSTEM PRESSURE


CAUTION:
·

Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.

·

After discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.



a.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:
·

When disconnecting the cable some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




b.
U153105E01
2.467,1.811 2.645,1.987 0.178,0.176 10 *1 1.595,1.114 2.435,1.87 false

Turn the lock lever and disconnect the connector of the fuel pump ECU.

Text in Illustration
*1 Lock Lever


c.

Connect the cable to the negative (-) battery terminal.


d.

Start the engine. After the engine has stopped on its own, turn the ignition switch off.

HINT:

DTC P0171/0174 (system too lean) may be set.



e.

Crank the engine again, and then check that the engine does not start.


f.

Loosen the fuel tank cap, and then discharge the pressure in the fuel tank completely.


g.
U153106E01
0.624,2.978 0.802,3.154 0.178,0.176 10 *1 0.93,2.947 0.8,3.068 false 3.084,2.965 3.262,3.141 0.178,0.176 10 *1 3.069,3.042 2.917,2.945 false

Connect the connector of the fuel pump ECU.


h.

Turn the lock lever and secure the connector with the lock lever.

Text in Illustration
*1 Lock Lever



FUEL SYSTEM


a.

When disconnecting the high pressure fuel line, a large amount of gasoline will spill out. Follow these procedures.

i.

Perform the "Discharge Fuel System Pressure" procedures above.


ii.
A133694

Put a container under the connecting part of the pressure line.


iii.

Slowly loosen the connection.


iv.

Disconnect the connection.


v.

Plug the connection with a rubber plug.



b.
A163532E09
1.156,3.385 1.156,3.719 false 0.708,3.375 0.708,3.625 false 1.135,1.188 1.135,1.417 false 0.771,1.469 0.771,1.156 false 0.177,0.094 0.385,0.281 0.208,0.188 10 false *a 0.167,2.135 0.365,2.292 0.198,0.156 10 false *b 1.083,3.75 1.292,3.917 0.208,0.167 10 false *2 0.656,3.656 0.844,3.823 0.188,0.167 10 false *1 1.063,1.417 1.271,1.583 0.208,0.167 10 false *2 0.698,1.469 0.885,1.635 0.188,0.167 10 false *1

Observe these precautions when removing and installing the injectors:

Text in Illustration
*1 O-Ring
*2 Delivery Pipe
*a CORRECT
*b INCORRECT

NOTICE:
·

Never reuse the O-ring.

·

When placing a new O-ring on the injector, do not damage it.

·

Coat a new O-ring with spindle oil or gasoline before installing it. Do not use engine oil, gear oil or brake oil.




c.
A163533E09
1.208,2.833 1.625,2.833 false 1.969,2.313 2.469,2.313 false 2.51,1.875 1.771,1.875 true 0.729,1.073 1.479,1.073 true 0.875,0.531 1.427,0.531 false 0.708,0.458 0.865,0.635 0.156,0.177 10 false *1 0.51,1 0.677,1.146 0.167,0.146 10 false *2 2.531,1.76 2.719,1.927 0.188,0.167 10 false *3 2.552,2.25 2.75,2.427 0.198,0.177 10 false *4 1.021,2.74 1.198,2.927 0.177,0.188 10 false *5

Install the injector to the delivery pipe and intake manifold as shown in the illustration.

Text in Illustration
*1 Delivery Pipe
*2 O-Ring
*3 Injector
*4 Insulator
*5 Cylinder Head

NOTICE:

Before installing the injector, apply spindle oil or gasoline on the place where the delivery pipe contacts the O-ring of the injector.



d.

Observe these precautions when disconnecting the fuel tube connector (for quick type A).

i.
A157617E14
0.219,0.24 0.521,0.438 0.302,0.198 10 false *a

for Fuel Hose Connector Cover Type:

Detach the lock claw by lifting up the cover, as shown in the illustration.

Text in Illustration
*a for Fuel Hose Connector Cover Type
V100135

Pull


ii.
A308865E07
0.663,0.444 0.858,0.621 0.196,0.177 10 *1 0.891,0.546 1.089,0.546 1.089,0.546 1.237,0.894 false 0.061,0.034 0.257,0.211 0.196,0.177 10 *a

for Fuel Pipe Clamp Type:

Remove the fuel pipe clamp from the fuel tube connector.

Text in Illustration
*a for Fuel Pipe Clamp Type
*1 Fuel Pipe Clamp


iii.

Check for dirt or mud on the pipe and around the connector before disconnection. Clean if necessary.


iv.
A088336

Pinch the connector and disconnect the connector and pipe.

Text in Illustration
V100135

Pinch
V100136

Pull

If the connector and the pipe are stuck together, pinch the connector, push and pull the pipe to disconnect the pipe and pull it out.

NOTICE:

Do not use any tools.



v.

Check for dirt or mud on the seal surface of the disconnected pipe. Clean if necessary.


vi.

To protect the disconnected pipe and connector from damage and contamination, cover it with a plastic bag.



e.
A130944

Observe these precautions when connecting the fuel tube connector (for quick type A).

Text in Illustration
V100135

Push

i.

Check that there is no damage or contamination in the connected part of the pipe.


ii.

Align the axis of the connector with the axis of the pipe. Push the pipe into the connector until the connector makes a "click" sound. If the connection is tight, apply a small amount of fresh spindle oil or gasoline on the tip of the pipe.


iii.
A130945

After having finished the connection, try to pull apart the pipe and the connector to confirm that they are securely connected.

Text in Illustration
V100135

Pull


iv.
A308865E07
0.663,0.444 0.858,0.621 0.196,0.177 10 *1 0.891,0.546 1.089,0.546 1.089,0.546 1.237,0.894 false 0.061,0.034 0.257,0.211 0.196,0.177 10 *a

for Fuel Pipe Clamp Type:

Install the fuel pipe clamp to the connector.

Text in Illustration
*a for Fuel Pipe Clamp Type
*1 Fuel Pipe Clamp


v.
A157616E08
0.26,0.167 0.51,0.406 0.25,0.24 12 false *a

for Fuel Hose Connector Cover Type:

Attach the lock claw to the connector by pushing down on the cover, as shown in the illustration.

Text in Illustration
*a for Fuel Hose Connector Cover Type
V100135

Push


vi.

Check that there is no fuel leakage.



f.

Observe these precautions when disconnecting the fuel tube connector (for Quick Type B).

i.

Check that there is no damage or foreign matter on the part of the pipe that contacts the connector.


ii.
A308868E06
1.281,1.583 0.781,1.583 0.781,1.583 0.781,1.156 false 1.156,1.156 1.156,1.583 false 2.573,0.208 2.688,0.208 2.688,0.208 2.771,0.427 false 2.354,0.135 2.552,0.302 0.198,0.167 10 false *1 1.333,1.448 1.521,1.615 0.188,0.167 10 false *c 1.146,0.26 1.323,0.438 0.177,0.177 10 false *b 0.49,1.156 0.688,1.333 0.198,0.177 10 false *a 1.281,1.146 1.469,1.323 0.188,0.177 10 false *a 2.135,3.01 2.333,3.188 0.198,0.177 10 false *b

Spread the tabs of the retainer outward and pull the retainer upwards to disconnect the connector from the pipe.

Text in Illustration
*1 Retainer
*a Spread
*b Pull
*c Tab

HINT:
·
A308884E05
1.854,2.26 1.708,2.26 1.708,2.26 1.542,2.594 false 0.51,1.229 0.51,1.479 0.51,1.479 0.594,1.479 false 2.458,0.688 2.458,0.333 2.458,0.333 2.542,0.333 false 1.906,2.177 2.115,2.365 0.208,0.188 10 false *b 0.646,1.396 0.833,1.583 0.188,0.188 10 false *1 0.396,0.438 0.594,0.604 0.198,0.167 10 false *a 2.594,0.24 2.813,0.427 0.219,0.188 10 false *1


·

The connector can also be disconnected from the pipe by inserting a screwdriver with a blade of 4 mm or less into the service hole in the back of the retainer and pulling the retainer upwards.

Text in Illustration
*1 Retainer
*a Pull
*b Service Hole

·
A308869

If the connector and pipe are stuck, pinch the fuel pipe by hand and push and pull the connector to disconnect it.




iii.

Check for foreign matter on the seal surface of the disconnected pipe. Clean if necessary.


iv.

To protect the disconnected pipe and connector from damage and foreign matter, cover them with a plastic bag.



g.

Observe these precautions when connecting the fuel tube connector (for Quick Type B).

i.

Check for foreign matter on the pipe and around the connector before connecting it. Clean if necessary.


ii.
A308870E06
2.375,1.583 2.375,1.438 2.375,1.438 2.865,1.323 false 2.292,1.625 2.49,1.802 0.198,0.177 10 false *1 1.406,1.792 1.615,1.969 0.208,0.177 10 false *a 0.906,0.417 1.094,0.594 0.188,0.177 10 false *a 3.198,0.906 3.385,1.083 0.188,0.177 10 false *a

Align the axis of the connector with the axis of the pipe. Push the connector onto the pipe, and then push in the retainer until a "click" sound is heard.

Text in Illustration
*1 Retainer
*a Push

NOTICE:
A308871

·

Before connecting the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.

·

After connecting the pipe and connector, check that the pipe and connector are securely connected by trying to pull them apart.



Text in Illustration
V100135

Pull


iii.

Check that there is no fuel leakage.




CHECK FOR FUEL LEAK


a.

Check that there are no fuel leaks after performing maintenance anywhere on the fuel system (See page Engine / Hybrid System>3UR-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).