Home › Engine / Hybrid System › 3UR-FE INTAKE / EXHAUST › INTAKE SYSTEM
RM27L0U _51 Engine / Hybrid System _049301 3UR-FE INTAKE / EXHAUST _0235601 INTAKE SYSTEM G

3UR-FE INTAKE / EXHAUST  INTAKE SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT INTAKE AIR CONTROL VALVE

a.

Remove the V-bank cover.


b.

Start the engine.


c.

Check that the VSV (for ACIS) is ON (seal) under both of the following conditions below.

·

Depressing the accelerator pedal to a throttle valve opening angle of 50° or more.

·

Revving the engine to 4700 rpm or less.


NOTICE:

Do not increase the engine speed to 5400 rpm or more.



d.
A162076E06
1.615,1.656 1.958,1.448 false 2.354,1.49 2.125,1.271 false 2.365,1.427 3.094,1.656 0.729,0.229 10 true ON (Seal) 0.854,1.573 1.604,1.844 0.75,0.271 10 true OFF (Vent)

Check that the VSV (for ACIS) is OFF (vent) under the following conditions below.

·

Releasing the accelerator pedal while under the VSV (for ACIS) OFF condition.

·

The engine is idling.



e.

Connect the Techstream to the DLC3.


f.

Perform the Active Test, and then check that the actuator rod operates.

If the result is not as specified, inspect the intake air control valve, vacuum tank and VSV (for ACIS) for normal operation. Replace malfunctioning parts as necessary.


g.

Install the V-bank cover.


Hide 2.CHECK INTAKE AIR CONTROL VALVE OPERATION

a.

Remove the V-bank cover.


b.
A162074E05
1.948,0.135 2.344,0.313 false 0.969,0.021 1.958,0.198 0.99,0.177 10 false Vacuum Gauge

Using a 3-way connector, connect a vacuum gauge to the actuator hose.


c.

Start the engine.


d.

While the engine is idling, check that the vacuum gauge indicates 0 kPa (0 mmHg, 0 in.Hg) and the rod is at the OFF position


e.

Fully depress the accelerator pedal quickly. Check that the VSV (for ACIS) turns ON and the rod moves in the ON direction.

NOTICE:

Fully depress and release the accelerator pedal within 1 second.



f.

Remove the vacuum gauge, and connect the vacuum hose to the actuator.


g.

Install the V-bank cover.


Hide 3.INSPECT INTAKE AIR CONTROL VALVE

a.
A162075E05
1.896,0.156 2.229,0.375 false 0.969,0.073 1.927,0.281 0.958,0.208 10 false Vacuum Pump

Inspect the diaphragm.

i.

Using a vacuum pump, apply a vacuum of 27 kPa (200 mmHg, 7.85 in.Hg). Check that the lever moves.

If the result is not as specified, replace the intake air surge tank.



Hide 4.CHECK AIR INDUCTION SYSTEM

HINT:
·

The illustration shows the areas that may draw in secondary air, which could lead to idling problems.

·

Perform "Inspection After Repair" after repairing air leaks in the intake system (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).



a.

Check that the hoses are installed correctly.


b.

Check for cracks, etc. in the hoses.

A162106E03
0.725,0.174 1.506,0.337 0.781,0.163 10 Air Cleaner 2.324,0.196 3.098,0.365 0.774,0.170 10 MAF Meter 3.037,0.608 4.145,0.771 1.107,0.163 10 Air Cleaner Hose 2.719,2.56 3.653,2.941 0.934,0.381 10 Throttle W/motor Body 0.902,1.709 1.627,1.851 0.725,0.142 10 Resonator 1.967,1.786 1.595,1.786 false 4.881,2.213 5.634,2.376 0.753,0.163 10 Purge VSV 4.72,2.917 6.244,3.246 1.524,0.330 10 Intake Air Control Valve Actuator (for ACIS) 5.763,4.357 6.975,4.665 1.211,0.309 10 Vacuum Switching Valve (for ACIS) 5.215,4.427 5.698,4.427 false 5.215,4.427 5.698,4.427 false 5.84,5.218 6.969,5.381 1.128,0.163 10 Ventilation Pipe 5.484,5.287 5.799,5.287 false 0.791,4.233 1.741,4.542 0.950,0.309 10 Fuel Pressure Regulator 2.086,5.288 1.791,5.288 false 2.079,6.549 2.998,6.691 0.920,0.142 10 Brake Booster 3.003,6.626 3.347,6.626 false 4.667,6.629 5.661,6.792 0.994,0.163 10 Intake Manifold 0.734,5.215 1.862,5.378 1.128,0.163 10 Ventilation Pipe 1.495,0.247 1.623,0.793 false 2.279,0.264 2.017,0.922 false 2.983,0.689 2.814,0.959 false 3.14,2.532 3.644,2.242 false 4.652,3.004 4.146,3.995 false 5.611,2.277 5.813,2.636 false 4.62,6.698 3.994,5.53 false 1.772,4.317 2.597,4.946 false