Home › Engine / Hybrid System › 3UR-FBE STARTING › RELAY
RM27L0U _51 Engine / Hybrid System _049308 3UR-FBE STARTING _0235638 RELAY G

3UR-FBE STARTING  RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 28300 1.INSPECT STARTER RELAY (ST)

a.
A379977E01
2,0.719 1.781,0.344 false 2.656,0.688 2.885,0.302 false 2.531,1.115 2.927,1.115 false 2.542,1.615 2.938,1.615 false 0.26,0.771 0.385,0.938 0.125,0.167 10 false 5 0.271,1.292 0.365,1.438 0.094,0.146 10 false 1 1.188,0.76 1.271,0.938 0.083,0.177 10 false 3 1.177,1.292 1.26,1.469 0.083,0.177 10 false 2 1.698,0.188 1.781,0.365 0.083,0.177 10 false 1 2.906,0.156 2.99,0.333 0.083,0.177 10 false 2 2.969,1.031 3.052,1.208 0.083,0.177 10 false 5 2.969,1.542 3.052,1.719 0.083,0.177 10 false 3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the relay.


Hide 85930G 2.INSPECT ACC CUT RELAY (ACC CUT)

a.
A087121E35
2.354,0.604 2.354,0.292 false 2.49,1.115 2.958,1.115 false 2.49,1.615 2.958,1.615 false 2.042,0.604 1.865,0.292 false 2.635,0.604 2.813,0.292 false 0.354,1.427 0.552,1.635 0.198,0.208 10 false 1 1.792,0.115 1.99,0.323 0.198,0.208 10 false 1 1.302,1.427 1.5,1.635 0.198,0.208 10 false 2 2.813,0.094 3.01,0.302 0.198,0.208 10 false 2 0.365,0.885 0.563,1.094 0.198,0.208 10 false 3 3,1.531 3.198,1.74 0.198,0.208 10 false 3 0.958,0.427 1.156,0.635 0.198,0.208 10 false 4 2.323,0.104 2.521,0.313 0.198,0.208 10 false 4 1.302,0.885 1.5,1.094 0.198,0.208 10 false 5 3,1.031 3.198,1.24 0.198,0.208 10 false 5

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Battery voltage not applied between terminals 1 and 2 Below 1 Ω
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 4 Battery voltage applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage applied between terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the relay.



Hide 82733A 3.INSPECT MAIN BODY ECU (ACC RELAY)

A379978E01
3.615,1.031 3.969,1.24 0.354,0.208 3.073,2.208 3.073,2.104 3.073,2.104 3.219,1.844 true 3.531,2.219 3.531,2.115 3.531,2.115 3.646,1.729 true 3.99,2.229 3.99,2.125 3.99,2.125 3.813,1.729 true 4.719,2.208 4.719,2.104 4.719,2.104 4.49,1.573 true 0.073,0.031 3.688,0.25 3.615,0.219 10 false Component without harness connected: (Main Body ECU) 3.688,1.052 3.958,1.198 0.271,0.146 10 false DD 3.01,2.219 3.281,2.365 0.271,0.146 10 false 62 3.469,2.219 3.74,2.365 0.271,0.146 10 false 47 3.917,2.219 4.188,2.365 0.271,0.146 10 false 45 4.688,2.208 4.958,2.354 0.271,0.146 10 false 8

a.

Measure the resistance of the ACC relay circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DD-47 - DD-8 Battery voltage not applied between DD-45 and DD-62 10 kΩ or higher
Battery voltage applied between DD-45 and DD-62 Below 1 Ω


If the result is not as specified, replace the main body ECU.