Home › Drivetrain › AB60E AUTOMATIC TRANSMISSION / TRANSAXLE › TORQUE CONVERTER CLUTCH AND DRIVE PLATE
RM27L0U _52 Drivetrain _049311 AB60E AUTOMATIC TRANSMISSION / TRANSAXLE _0235663 TORQUE CONVERTER CLUTCH AND DRIVE PLATE G

AB60E AUTOMATIC TRANSMISSION / TRANSAXLE  TORQUE CONVERTER CLUTCH AND DRIVE PLATE  INSPECTION  


PROCEDURE

Hide 32000 1.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

a.

Inspect the 1-way clutch.

i.
C151051E17
1.469,0.188 1.823,0.417 0.354,0.229 10 true Free 0.885,0.844 1.25,1.073 0.365,0.229 10 true Lock

Press on the serrations of the starter with a finger and rotate it. Check that it rotates smoothly when turned clockwise and locks when turned counterclockwise.

If necessary, clean the converter and recheck the 1-way clutch.

Replace the converter if the 1-way clutch still fails the check.



b.
C352866E01
0.646,0.094 2.958,0.458 2.313,0.365 10 false Sample showing maximum allowable amount of powder in ATF 1.313,4.083 2.104,4.281 0.792,0.198 10 false Actual Size

Determine the condition of the torque converter clutch.

i.

Check that the following conditions are met:

·

During the stall test or when the shift lever is in N, metallic sounds are not emitted from the torque converter clutch.

·

The 1-way clutch turns in one direction and locks in the other direction.

·

The amount of powder in the ATF is not greater than the sample shown in the illustration.


If the results are not as specified, replace the torque converter clutch assembly.

HINT:

The sample illustration shows approximately 0.25 liters (0.26 US qts, 0.22 Imp. qts) of the ATF taken from a removed torque converter clutch.




c.

Replace the ATF in the torque converter clutch.

i.

If the ATF is discolored and/or has a foul odor, stir the ATF in the torque converter clutch thoroughly and drain the ATF with the torque converter facing upward.



d.
D025368E65
1.76,1.844 2.156,1.271 true 0.208,0.063 0.948,0.26 0.74,0.198 10 false CORRECT 1.26,0.063 2.167,0.26 0.906,0.198 10 false INCORRECT 2.188,0.906 2.885,1.271 0.698,0.365 10 false Bottom is damaged

Prevent deformation of the torque converter clutch and damage to the oil pump gear.

i.

When any marks due to interference are found on the end of the bolt for the torque converter clutch and on the bottom of the bolt hole, replace the bolt and torque converter clutch.


ii.

All of the bolts should be the same length.


iii.

Make sure no spring washers are missing.



Hide 2.INSPECT DRIVE PLATE

C352867E01
1.333,1.083 1.49,1.281 0.156,0.198 10 false 1 1.604,0.313 1.76,0.51 0.156,0.198 10 false 2 2.323,0.219 2.479,0.417 0.156,0.198 10 false 3 2.896,0.906 3.052,1.104 0.156,0.198 10 false 4 2.813,1.667 2.969,1.865 0.156,0.198 10 false 5 2.104,1.833 2.26,2.031 0.156,0.198 10 false 6 0.49,1.802 1.813,2.021 1.323,0.219 10 false : Measuring point

a.

Check the drive plate for damage.


b.

Set up a dial indicator and measure the runout of the 6 portions around the torque converter fitting surfaces.

Maximum runout:

0.20 mm (0.00787 in.)


If the runout is more than the maximum, or the drive plate is damaged, replace the drive plate (See page Engine / Hybrid System>3UR-FE ENGINE MECHANICAL>REAR CRANKSHAFT OIL SEAL>INSTALLATION).