Home › Drivetrain › AB60E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION UNIT
RM27L0U _52 Drivetrain _049311 AB60E AUTOMATIC TRANSMISSION / TRANSAXLE _0235664 AUTOMATIC TRANSMISSION UNIT A

AB60E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION UNIT  DISASSEMBLY  


PROCEDURE

Hide 35572 1.REMOVE TRANSMISSION CONTROL SHAFT LEVER RH

a.
C274989

Remove the nut, spring washer and control shaft lever.


Hide 84540 2.REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.
C274990

Using a screwdriver, bend the tabs of the lock washer.


b.

Remove the nut, lock washer and bolt.


c.

Remove the park/neutral position switch.

HINT:

Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch as the detent spring may become detached from the manual valve lever shaft.



Hide 89413B 3.REMOVE SPEED SENSOR

a.
C274991

Remove the 2 bolts and 2 speed sensors.


b.

Remove the 2 O-rings from the sensors.


Hide 33490F 4.REMOVE TRANSMISSION OIL COOLER ASSEMBLY

a.
C161367

Remove the 3 bolts and transmission oil cooler with transmission oil cooler spacer.


b.

Separate the transmission oil cooler from the transmission oil cooler spacer.


c.

Remove the 4 O-rings.


Hide 35122 5.REMOVE AUTOMATIC TRANSMISSION BREATHER TUBE

a.
C178810

Remove the 2 bolts.


b.

Remove the breather tube.


c.

Remove the O-ring from the tube.


Hide 35111 6.REMOVE AUTOMATIC TRANSMISSION HOUSING

a.
C159660

Remove the 14 bolts.


b.

Remove the transmission housing.


Hide 7.REMOVE EXTENSION HOUSING SUB-ASSEMBLY

a.
C161608

Remove the 10 bolts.


b.
C161609

Remove the extension housing.

HINT:

Tap on the circumference of the extension housing with a plastic-faced hammer to remove the extension housing.



Hide 35015C 8.REMOVE EXTENSION HOUSING REAR OIL SEAL

a.
C161612E01
2.287,0.163 2.613,0.364 0.326,0.200 10 SST 1.92,0.247 2.249,0.247 false

Using SST, tap out the oil seal.

SST
09308-00010  


Hide 35104 9.FIX AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY

a.
C161613

Install the transmission case on the overhaul attachment.


Hide 35106 10.REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

a.
C353371

Remove the drain plug, 12 bolts, oil pan and gasket.

NOTICE:

Do not turn the transmission over as this will contaminate the valve body with foreign matter on the bottom of the pan.



Hide 35106 11.INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

Hide 35330 12.REMOVE VALVE BODY OIL STRAINER ASSEMBLY

a.
C178807

Turn over the transmission.


b.

Remove the 4 bolts and oil strainer from the valve body.


c.

Remove the O-ring from the oil strainer.


Hide 82125J 13.REMOVE TRANSMISSION WIRE

a.
U152298

Remove the 2 bolts and 2 temperature sensor clamps.


b.

Disconnect the 2 ATF temperature sensors.


c.

Disconnect the 9 connectors from the solenoid valves.


d.
C161614

Remove the 2 bolts and pull out the No. 1 and No. 2 transmission wires.


e.

Pull the transmission wires out of the transmission case.


f.
C161615

Remove the 2 O-rings from the transmission wires.


Hide 35410 14.REMOVE TRANSMISSION VALVE BODY ASSEMBLY

a.
U152342

Remove the bolt, detent spring cover and detent spring.


b.

Remove the 19 bolts.


c.

Remove the valve body assembly.


Hide 35145C 15.REMOVE TRANSMISSION CASE GASKET

a.
C161616

Remove the 3 gaskets.


Hide 35159 16.REMOVE BRAKE DRUM GASKET

a.
C161617

Remove the 3 gaskets.


Hide 35251 17.REMOVE CHECK BALL BODY

a.
C161618E03
1.844,0.573 1.521,0.573 true 1.844,1.167 1.427,1.167 true 1.875,0.479 2.979,0.708 1.104,0.229 10 true Check Ball Body 1.896,1.073 2.375,1.281 0.479,0.208 10 false Spring

Remove the check ball body and spring.


Hide 35425A 18.REMOVE C-2 ACCUMULATOR PISTON

a.
C161619

While applying compressed air to the oil hole, remove the C-2 accumulator piston and spring.


b.

Remove the 2 O-rings from the piston.

NOTICE:

Be careful as the C-3 and B-3 accumulator pistons may jump out.



Hide 35427K 19.REMOVE B-3 ACCUMULATOR PISTON

a.
C161619

While applying compressed air to the oil hole, remove the B-3 accumulator piston and spring.


b.

Remove the 2 O-rings from the piston.

NOTICE:

Be careful as the C-3 accumulator piston may jump out.



Hide 35426D 20.REMOVE C-3 ACCUMULATOR PISTON

a.
C161620

While applying compressed air to the oil hole, remove the C-3 accumulator piston and spring.


b.

Remove the 2 O-rings from the piston.


Hide 35424F 21.REMOVE B-1 ACCUMULATOR VALVE

a.
C161621

Remove the B-1 accumulator valve and 2 springs.


Hide 35595 22.REMOVE PARKING LOCK PAWL BRACKET

a.
C161622

Remove the 3 bolts and bracket.


Hide 35501 23.REMOVE PARKING LOCK ROD SUB-ASSEMBLY

a.
U152320

Disconnect the parking lock rod from the manual valve lever.


Hide 35557 24.REMOVE PARKING LOCK PAWL

a.
U152321

Pull out the parking lock pawl shaft from the front side, and then remove the lock pawl and spring.


b.

Remove the E-ring from the shaft.


Hide 35505 25.REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY

a.
D027918E01
2.99,0 3.414,0.103 0.424,0.103

Using a screwdriver and hammer, cut off the spacer and remove it from the shaft.


b.
C161626

Using a pin punch and hammer, tap out the spring pin.

HINT:

Slowly tap out the spring pin so that it does not fall into the transmission case.



c.

Pull the manual valve lever shaft out through the transmission case, and remove the manual valve lever.


Hide 35506F 26.REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

a.
C161628

Using a screwdriver, pry out the 2 oil seals.

NOTICE:

Be careful not to damage the transmission case.


HINT:

Wrap the tip of the screwdriver with tape before use.



Hide 27.REMOVE OIL PUMP ASSEMBLY

a.
C161629

Remove the 10 bolts.


b.
C161630E01
2.68,0.691 2.999,0.879 0.319,0.189 10 SST 2.645,0.827 2.182,0.949 false

Using SST, pull out the oil pump.

SST
09950-40011  (09951-04010, 09953-04020, 09958-04011, 09952-04010, 09954-04010, 09955-04031, 09955-04031)


c.
C161631

Remove the 2 thrust bearing races and O-ring from the oil pump.


Hide 28.REMOVE CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

a.
C161632

Remove the clutch drum and input shaft drum assembly from the transmission case.


b.
C161633

Remove the clutch drum thrust washer and 2 thrust needle roller bearings.


Hide 35780B 30.REMOVE NO. 2 1-WAY CLUTCH ASSEMBLY

a.
C161634

Remove the No. 2 1-way clutch and clutch drum thrust washer from the clutch drum and input shaft assembly.


Hide 35601 31.FIX CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

a.
C161636E01
2.558,0.986 3.204,1.207 0.646,0.221 10 Oil Pump 0.033,0.93 0.666,1.454 0.633,0.524 10 Torque Converter Clutch 1.048,1.254 0.795,1.101 false 2.34,1.069 2.54,1.069 false

Place the oil pump onto the torque converter clutch, and then place the clutch drum and input shaft assembly onto the oil pump.


Hide 35049 32.REMOVE REVERSE CLUTCH HUB SUB-ASSEMBLY

a.
C161637

Using a screwdriver, remove the snap ring.


b.
C161638

Remove the reverse clutch reaction sleeve and reverse clutch hub sub-assembly with the rear clutch disc set from the clutch drum.


Hide 35677C 33.REMOVE REAR CLUTCH DISC SET

a.
C161640

Remove the selective reverse clutch flange, 5 discs and 4 plates from the reverse clutch hub.


b.
C162148

Remove the reverse clutch flange from the clutch drum.


Hide 35061 36.REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY

a.
C161641

Remove the thrust needle roller bearing, forward clutch hub and No. 3 clutch hub thrust washer from the clutch drum.


Hide 35064 38.REMOVE COAST CLUTCH HUB SUB-ASSEMBLY WITH NO. 4 1-WAY CLUTCH ASSEMBLY

a.
C161642

Remove the 2 thrust needle roller bearings, coast clutch hub with the No. 4 1-way clutch and thrust bearing race from the clutch drum.


Hide 35790H 40.REMOVE NO. 4 1-WAY CLUTCH ASSEMBLY

a.
C161643

Separate the No. 4 1-way clutch from the coast clutch hub.


b.

Remove the No. 2 clutch hub thrust washer from the coast clutch hub.


Hide 35633B 41.REMOVE FORWARD MULTIPLE DISC CLUTCH CLUTCH DISC SET

a.
C161644

Using a screwdriver, remove the hole snap ring.


b.
C161645

Remove the flange, 6 discs, 6 plates and cushion plate from the input shaft.


Hide 35633B 42.INSPECT FORWARD MULTIPLE DISC CLUTCH CLUTCH DISC

Hide 35685 43.REMOVE COAST CLUTCH DISC SET

a.
C161646

Using a screwdriver, remove the hole snap ring.


b.
C161647

Remove the flange, 4 discs and 4 plates from the input shaft.


Hide 35701 45.REMOVE INPUT SHAFT SUB-ASSEMBLY

a.
C161648

Remove the input shaft from the clutch drum.


Hide 35712A 46.REMOVE INPUT SHAFT OIL SEAL RING

a.
C161649

Remove the 4 oil seal rings from the input shaft.


Hide 35621Y 47.REMOVE COAST CLUTCH PISTON

a.
C161650E01
2.76,0.626 3.084,0.812 0.324,0.186 10 SST 2.137,0.648 2.715,0.708 2.715,0.708 1.633,0.943 false

Place SST on the No. 1 clutch balancer, and compress the return spring with a press.

SST
09350-30020  (09350-07040)


b.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07070)


c.
C161651

Remove the No. 1 clutch balancer and forward clutch return spring from the input shaft.


d.
C161652

Remove the O-ring from the No. 1 clutch balancer.


e.
C161653

Hold the coast clutch piston by hand and apply compressed air to the input shaft to remove the coast clutch piston.


Hide 35602A 48.REMOVE FORWARD CLUTCH PISTON SUB-ASSEMBLY

a.
C161654

Hold the forward clutch piston by hand and apply compressed air to the input shaft to remove the forward clutch piston.


b.
C162744

Remove the O-ring from the input shaft.


Hide 35603A 49.INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

Hide 35667A 50.REMOVE DIRECT CLUTCH DISC SET

a.
C159654

Using a screwdriver, remove the 2 hole snap rings from the clutch drum.


b.
C161655

Remove the direct clutch flange, 5 discs and 5 plates from the clutch drum.


Hide 35668 52.REMOVE NO. 3 CLUTCH BALANCER

a.
C161656E01
2.693,0.685 3.029,0.858 0.336,0.173 10 SST 2.127,0.674 2.641,0.815 2.641,0.815 1.988,1.641 false

Place SST on the No. 3 clutch balancer, and compress the return spring with a press.

SST
09380-60010  (09381-06020, 09381-06030, 09381-06040, 09381-06050, 09381-06080, 09381-06070)


b.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07070)


c.

Remove the No. 3 clutch balancer.


d.
C161657

Remove the reverse clutch return spring and O-ring from the reverse clutch piston sub-assembly.


Hide 35047 53.INSPECT REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY

Hide 35048 54.REMOVE REVERSE CLUTCH PISTON SUB-ASSEMBLY

a.
C161700

Remove the reverse clutch piston from the clutch drum.


b.
C161702

Remove the O-ring from the reverse clutch piston.


c.
C161703

Remove the O-ring from the clutch drum.


Hide 35606A 55.REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY

a.
C161704E01
0.111,0.511 0.425,0.699 0.314,0.188 10 SST 1.952,1.079 0.504,0.636 0.504,0.636 1.118,0.73 false

Place SST on the direct clutch piston, and compress the return spring with a press.

SST
09380-60010  (09381-06030, 09381-06040, 09381-06080)


b.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07070)


c.

Place the oil pump onto the torque converter clutch, and then place the clutch drum onto the oil pump.


d.
U152323E01
2.451,1.989 3.037,2.190 0.586,0.201 10 Oil Hole 3.18,0.943 3.18,2.099 3.18,2.099 3.101,2.099 false

Hold the direct clutch piston by hand and apply compressed air to the oil hole of the oil pump as shown in the illustration to remove the direct clutch piston with the No. 2 clutch balancer and direct clutch return spring sub-assembly.


e.
C161706

Remove the No. 2 clutch balancer and direct clutch return spring sub-assembly from the direct clutch piston.


f.
C161812

Remove the 2 O-rings from the direct clutch piston.


Hide 35604 56.INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

Hide 35679C 57.REMOVE NO. 3 BRAKE SNAP RING

a.
C161635

Using a screwdriver, remove the No. 3 brake snap ring from the transmission case.


Hide 35066 58.REMOVE NO. 3 BRAKE DISC SET

a.
C161707

Remove the 2 flanges, 4 discs and 3 plates from the transmission case.


Hide 35624J 60.REMOVE NO. 3 BRAKE PISTON HOLE SNAP RING

a.
C161708E02
2.781,0.385 2.365,0.25 true 2.823,0.302 3.135,0.5 0.313,0.198 10 false SST

Using SST, remove the snap ring.

SST
09350-30020  (09350-07060)


Hide 35664 61.REMOVE NO. 3 BRAKE CYLINDER WITH NO. 3 BRAKE PISTON AND NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C161709

Remove the No. 3 brake cylinder with the No. 3 brake piston and No. 3 brake piston return spring from the transmission case.


Hide 35624 62.REMOVE NO. 3 BRAKE PISTON

a.
C162151E01
0.361,0.071 0.722,0.257 0.361,0.187 10 SST 0.713,0.202 1.031,0.367 false

Using SST and a press, compress the return spring and remove the snap ring and No. 3 brake piston return spring with a screwdriver.

SST
09380-60010  (09381-06020, 09381-06040, 09381-06060, 09381-06100, 09381-06110)


b.
C161712

Hold the No. 3 brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the No. 3 brake cylinder to remove the No. 3 brake piston.


c.
C161713

Remove the 2 O-rings from the No. 3 brake piston.


Hide 35046 63.INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

Hide 35790 64.REMOVE 1-WAY CLUTCH ASSEMBLY WITH 1-WAY CLUTCH INNER RACE SUB-ASSEMBLY

a.
C161710

Remove the 1-way clutch with 1-way clutch inner race from the transmission case.


Hide 35707C 66.REMOVE 1-WAY CLUTCH INNER RACE SUB-ASSEMBLY

a.
C161711

Separate the 1-way clutch inner race from the 1-way clutch and remove the No. 1 planetary carrier thrust washer.


Hide 35720 67.REMOVE FRONT PLANETARY GEAR ASSEMBLY

a.
C161714

Remove the front planetary gear and thrust needle roller bearing from the transmission case.


b.
C161715

Remove the No. 2 planetary carrier thrust washer, thrust bearing race and front planetary sun gear from the front planetary gear.


Hide 35743 69.REMOVE FRONT PLANETARY RING GEAR WITH FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY AND CENTER PLANETARY RING GEAR

a.
C161716

Remove the front planetary ring gear with the front planetary ring gear flange and center planetary ring gear from the transmission case.


b.

Remove the thrust needle roller bearing and thrust bearing race.


Hide 35743 70.REMOVE FRONT PLANETARY RING GEAR

a.
C161717

Using a screwdriver, remove the snap ring.


b.
C161718

Remove the front planetary ring gear from the center planetary ring gear.


Hide 35763 71.REMOVE CENTER PLANETARY RING GEAR

a.
C161719

Using a screwdriver, remove the snap ring.


b.
C161720

Remove the center planetary ring gear from the front planetary ring gear flange.


Hide 35681A 72.REMOVE NO. 1 BRAKE DISC SET

a.
C161721

Remove the flange, 4 discs and 4 plates from the transmission case.


Hide 35698 74.REMOVE NO. 1 BRAKE CYLINDER WITH NO. 1 BRAKE PISTON

a.
C162153E01
3.022,1.461 3.345,1.661 0.323,0.200 10 SST 2.987,1.511 2.699,1.434 false

Place SST on the No. 1 brake piston return spring, and compress the return spring.

SST
09380-60010  (09381-06010, 09381-06020, 09381-06050, 09381-06060, 09381-06090, 09381-06100, 09381-06110, 09381-06120)


b.

Using a screwdriver, remove the snap ring from the transmission case.


c.
C161723

Remove the brake piston return spring and No. 1 brake piston with No. 1 brake cylinder from the transmission case.


Hide 35608J 75.INSPECT BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

Hide 35621V 76.REMOVE NO. 1 BRAKE PISTON

a.
C161724

Hold the No. 1 brake piston and apply compressed air to the No. 1 brake cylinder to remove the No. 1 brake piston.

HINT:

If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.



b.
C162732

Remove the 2 O-rings from the No. 1 brake piston.


Hide 35682A 77.REMOVE NO. 2 BRAKE DISC SET

a.
C162561E02
2.99,1.677 2.656,1.438 true 3.021,1.635 3.333,1.865 0.313,0.229 10 true SST

Place SST on the No. 2 brake flange, and compress the return spring.

SST
09380-60010  (09381-06010, 09381-06020, 09381-06050, 09381-06070, 09381-06090, 09381-06120)


b.

Using a screwdriver, remove the snap ring from the transmission case.


c.
C161726

Remove the 2 flanges, 4 discs, 3 plates and brake piston return spring from the transmission case.


Hide 35045 79.INSPECT NO. 2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

Hide 35750 80.REMOVE CENTER PLANETARY GEAR ASSEMBLY

a.
C161727

Remove the center planetary gear and planetary sun gear from the transmission case.


Hide 35699 82.REMOVE NO. 2 BRAKE CYLINDER WITH NO. 2 BRAKE PISTON

a.
C161728

Remove the No. 2 brake cylinder with the No. 2 brake piston from the transmission case.


Hide 35622G 83.REMOVE NO. 2 BRAKE PISTON

a.
C162149

Hold the No. 2 brake piston and apply compressed air to the No. 2 brake cylinder to remove the No. 2 brake piston.

HINT:

If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.



b.
C162730

Remove the 2 O-rings from the No. 2 brake piston.


Hide 35713 84.REMOVE INTERMEDIATE SHAFT WITH NO. 3 1-WAY CLUTCH ASSEMBLY, REAR PLANETARY RING GEAR FLANGE AND REAR PLANETARY RING GEAR

a.
C161730E02
0.51,1.354 0.51,1.01 true 0.365,1.375 0.667,1.563 0.302,0.188 10 true SST

Using SST, remove the snap ring from the transmission case.

SST
09350-30020  (09350-07060)


b.
C161731

Remove the intermediate shaft with No. 3 1-way clutch, rear planetary ring gear flange and rear planetary ring gear from the transmission case.


Hide 35770C 86.REMOVE NO. 3 1-WAY CLUTCH ASSEMBLY

a.
C161732

Remove the No. 3 1-way clutch and 1-way clutch inner race from the intermediate shaft.


Hide 35761 87.REMOVE REAR PLANETARY RING GEAR

a.
C161733

Remove the rear planetary ring gear with rear planetary ring gear flange, 3 thrust bearing races and thrust needle roller bearing from the intermediate shaft.


b.
C161734

Using a screwdriver, remove the snap ring.


c.

Remove the rear planetary ring gear flange from the rear planetary ring gear.


Hide 35684 89.REMOVE NO. 4 BRAKE DISC SET

a.
C161736

Remove the 2 flanges, 7 discs and 6 plates from the transmission case.


Hide 35639B 91.REMOVE BRAKE PLATE STOPPER SPRING

C161735

NOTICE:

When removing the stopper spring, do not apply excessive force and do not deform it.


Hide 35760 92.REMOVE REAR PLANETARY GEAR ASSEMBLY

a.
C161610

Using snap ring expander, remove the snap ring.


b.
C161611

Remove the rear planetary flange thrust bearing race, thrust needle roller bearing and thrust bearing race.


c.
C161737

Remove the rear planetary gear from the transmission case.


d.
C161738

Remove the 2 thrust needle roller bearings from the rear planetary gear.


e.
C161739

Remove the thrust bearing race from the transmission case.


Hide 35623H 94.REMOVE 1ST AND REVERSE BRAKE PISTON

a.
C162152E01
0.206,0.522 0.557,0.737 0.350,0.215 10 SST 0.913,0.709 0.601,0.626 false

Place SST on the spring retainer and compress the brake return spring.

SST
09380-60010  (09381-06030, 09381-06040, 09381-06080, 09381-06120, 09381-06130, 09381-05040, 09381-05050)


b.

Using SST, remove the snap ring and brake return spring.

SST
09350-30020  (09350-07070)


c.
C161740

Hold the 1st and reverse brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transmission case to remove the 1st and reverse brake piston.

HINT:

If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.



d.
C161741

Remove the 3 O-rings from the 1st and reverse brake piston.


Hide 35068 95.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY