CHECK ECM
Each ECM terminal's standard voltage is shown in the table below.
In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".
Use the illustration above as a reference for the ECM terminals.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| D56-120 (NSW) - D56-81 (E1) | L - BR | PNP switch signal | ·
Ignition switch ON ·
Shift lever in P or N |
Below 1 V |
·
Ignition switch ON ·
Shift lever not in P or N |
11 to 14 V | |||
| D56-2 (P) - D56-81 (E1) | G-B - BR | P shift position switch signal | ·
Ignition switch ON ·
Shift lever in P |
11 to 14 V |
·
Ignition switch ON ·
Shift lever not in P |
Below 1 V | |||
| D56-26 (R) - D56-81 (E1) | L-R - BR | R shift position switch signal | ·
Ignition switch ON ·
Shift lever in R |
11 to 14 V |
·
Ignition switch ON ·
Shift lever not in R |
Below 1 V | |||
| D56-25 (N) - D56-81 (E1) | G-W - BR | N shift position switch signal | ·
Ignition switch ON ·
Shift lever in N |
11 to 14 V |
·
Ignition switch ON ·
Shift lever not in N |
Below 1 V | |||
| D56-27 (D) - D56-81 (E1) | G - BR | D shift position switch signal | ·
Ignition switch ON ·
Shift lever in D |
11 to 14 V |
·
Ignition switch ON ·
Shift lever not in D |
Below 1 V | |||
| A27-25 (S) - D56-81 (E1) | Y - BR | S shift position switch signal | ·
Ignition switch ON ·
Shift lever in S |
11 to 14 V |
·
Ignition switch ON ·
Shift lever not in S |
Below 1 V | |||
| A27-38 (SFTU) - D56-81 (E1) | G - BR | Up-shift shift position switch signal | ·
Ignition switch ON ·
Shift lever in S |
11 to 14 V |
·
Ignition switch ON ·
Shift lever "+" position (up-shift) |
Below 1 V | |||
| A27-27 (SFTD) - D56-81 (E1) | BE - BR | Down-shift position switch signal | ·
Ignition switch ON ·
Shift lever in S |
11 to 14 V |
·
Ignition switch ON ·
Shift lever "-" position (down-shift) |
Below 1 V | |||
| D56-7 (S1) - D56-81 (E1) | R - BR | S1 solenoid signal | 1st gear | Below 1 V |
| Not on 1st gear | 11 to 14 V | |||
| D56-6 (S2) - D56-81 (E1) | W - BR | S2 solenoid signal | 1st, 2nd or 6th gear | 11 to 14 V |
| 3rd, 4th or 5th gear | Below 1 V | |||
| D56-3 (S3) - D56-81 (E1) | G-W - BR | S3 solenoid signal | 1st, 2nd or 3rd gear | 11 to 14 V |
| 4th, 5th or 6th gear | Below 1 V | |||
| D56-5 (S4) - D56-81 (E1) | G-R - BR | S4 solenoid signal | 5th or 6th gear | 11 to 14 V |
| 1st, 2nd, 3rd or 4th gear | Below 1 V | |||
| D56-4 (SR) - D56-81 (E1) | G - BR | SR solenoid signal | 1st, 2nd, 3rd or 4th gear | 11 to 14 V |
| 5th or 6th gear | Below 1 V | |||
| D56-14 (SL1+) - D56-15 (SL1-) | Y - L | SL1 solenoid signal | 5th or 6th gear | Pulse generation |
| D56-12 (SL2+) - D56-13 (SL2-) | G-R - L-W | SL2 solenoid signal | Engine is idling | Pulse generation |
| D56-9 (SLT+) - D56-8 (SLT-) | B - G-B | SLT solenoid signal | Engine is idling | Pulse generation |
| D56-10 (SLU+) - D56-11 (SLU-) | L-Y - L-R | SLU solenoid signal | 5th (lock-up) gear or 6th (lock-up) gear | Pulse generation |
| D56-122 (THO1) - D56-98 (ETHA) | G-Y - BR | No. 1 ATF temperature sensor signal | No. 1 ATF temperature: 115°C (239°F) or higher | Below 1.5 V |
| D56-99 (THO2) - D56-98 (ETHA) | L - BR | No. 2 ATF temperature sensor signal | No. 2 ATF temperature: 115°C (239°F) or higher | Below 1.5 V |
| D56-101 (SP2+) - D56-100 (SP2-) | Y - B | Speed sensor SP2 signal | Vehicle speed 20 km/h (12 mph) | Pulse generation
(see waveform 1) |
| D56-124 (NT+) - D56-123 (NT-) | Y - B | Speed sensor NT signal | Engine is idling
(shift lever in P or N) |
Pulse generation
(see waveform 2) |
| A27-10 (CANH) - D56-81 (E1) | GR - BR | CAN communication line | Ignition switch ON | Pulse generation
(see waveform 3) |
| A27-11 (CANL) - D56-81 (E1) | W - BR | CAN communication line | Ignition switch ON | Pulse generation
(see waveform 4) |
| A27-51 (PWR) - D56-81 (E1) | L - BR | Tow/haul pattern select switch signal | ·
Ignition switch ON ·
Tow/haul pattern select switch ON |
0 to 1.5 V |
·
Ignition switch ON ·
Tow/haul pattern select switch OFF |
Pulse generation* |
*: Voltage is input intermittently as this is an intermittent circuit. (Voltage varies between a peak of 7.5 to 14 V and a low of 0 to 1.5 V.)
Using an oscilloscope, check waveform 1.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | D56-101 (SP2+) - D56-100 (SP2-) |
| Tool setting | 2 V/DIV., 20 msec./DIV. |
| Condition | Vehicle speed 20 km/h (12 mph) |
Using an oscilloscope, check waveform 2.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | D56-124 (NT+) - D56-123 (NT-) |
| Tool setting | 1 V/DIV., 2 msec./DIV. |
| Condition | Engine is idling (Shift lever in P or N) |
Using an oscilloscope, check waveform 3.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | A27-10 (CANH) - D56-81 (E1) |
| Tool setting | 1 V/DIV., 10 μsec./DIV. |
| Condition | Ignition switch ON |
Using an oscilloscope, check waveform 4.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | A27-11 (CANL) - D56-81 (E1) |
| Tool setting | 1 V/DIV., 10 μsec./DIV. |
| Condition | Ignition switch ON |