Home › Drivetrain › AB60E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM27L0U _52 Drivetrain _049311 AB60E AUTOMATIC TRANSMISSION / TRANSAXLE _0235670 AUTOMATIC TRANSMISSION SYSTEM J

AB60E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  Transmission Control Switch Circuit  


DESCRIPTION

When moving the shift lever to S using the transmission control switch, it is possible to switch the shift range among "1" (1st range) and "6" (6th range).

Shifting to "+" once raises the shift range by one, and shifting to "-" lowers the shift range by one.

WIRING DIAGRAM

C179318E10
5.427,1.094 5.656,1.26 0.229,0.167 10 false 25 4.198,2.271 4.292,2.438 0.094,0.167 10 false 1 3.729,2.052 4.198,2.25 0.469,0.198 10 false SFTD 4.198,1.677 4.302,1.844 0.104,0.167 10 false 2 3.729,1.458 4.198,1.656 0.469,0.198 10 false SFTU 4.198,1.094 4.323,1.26 0.125,0.167 10 false 7 4,0.875 4.125,1.073 0.125,0.198 10 false S 2.667,1.094 2.771,1.26 0.104,0.167 10 false 3 2.854,0.885 3.094,1.083 0.24,0.198 10 false IG 2.667,2.271 2.792,2.438 0.125,0.167 10 false 5 2.854,2.052 3.094,2.25 0.24,0.198 10 false E 5.75,0.99 6.177,1.188 0.427,0.198 10 false S 5.427,1.677 5.656,1.844 0.229,0.167 10 false 38 5.75,1.594 6.177,1.792 0.427,0.198 10 false SFTU 5.427,2.271 5.656,2.438 0.229,0.167 10 false 27 5.75,2.167 6.177,2.365 0.427,0.198 10 false SFTD 2.583,2.948 4.365,3.146 1.781,0.198 10 false Transmission Control Switch 0.229,0.979 1.542,1.177 1.313,0.198 10 false from Ignition Switch 5.927,2.927 6.229,3.094 0.302,0.167 10 false A27 5.927,3.083 6.354,3.281 0.427,0.198 10 false ECM 2.583,2.76 2.885,2.958 0.302,0.198 10 false H31

PROCEDURE

1.INSPECT TRANSMISSION CONTROL SWITCH
a.
C146679E29
1.615,1.292 0.938,1.042 true 0.927,1.854 1.604,1.604 true 1.802,1.281 2.646,1.031 true 2,1.354 2.677,1.354 true 2.646,1.854 1.969,1.604 true 0.073,0.052 2.604,0.417 2.531,0.365 10 false Component without harness connected: (Transmission Control Switch) 0.771,0.927 1.021,1.125 0.25,0.198 10 false IG 0.771,1.781 0.938,1.979 0.167,0.198 10 false S 2.698,0.906 3.208,1.104 0.51,0.198 10 false SFTU 2.719,1.25 3.229,1.448 0.51,0.198 10 false SFTD 2.698,1.792 2.875,1.99 0.177,0.198 10 false E

Disconnect the H31 transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IG) - 7 (S) Shift lever in S, "+" and "-" Below 1 Ω
2 (SFTU) - 5 (E) Shift lever continuously in "+"
(Up-shift)
Below 1 Ω
1 (SFTD) - 5 (E) Shift lever continuously in "-"
(Down-shift)
Below 1 Ω
3 (IG) - 7 (S) Shift lever not in S, "+" and "-" 10 kΩ or higher
2 (SFTU) - 5 (E) Shift lever in S 10 kΩ or higher
1 (SFTD) - 5 (E) Shift lever in S 10 kΩ or higher




OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY, BODY GROUND)

NG

REPLACE TRANSMISSION FLOOR SHIFT ASSEMBLY (TRANSMISSION CONTROL SWITCH)

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY, BODY GROUND)
a.
U153411E02
1.823,1.771 2.396,1.458 true 0.833,2.479 1.417,2.167 true 0.49,1.688 0.865,1.917 0.375,0.229 10 false H31 0.063,0.052 2.469,0.417 2.406,0.365 10 false Front view of wire harness connector: (to Transmission Control Switch) 0.708,2.417 0.906,2.615 0.198,0.198 10 false E 2.438,1.344 2.677,1.542 0.24,0.198 10 false IG

Disconnect the H31 transmission control switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H31-3 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H31-5 (E) - Body ground Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.
U153486E02
1.979,2.896 2.156,2.073 true 2.938,2.896 2.156,1.844 true 1.188,2.896 1.979,1.844 true 0.073,0.063 2.479,0.427 2.406,0.365 10 false Front view of wire harness connector: (to ECM) 1.688,1.052 2.063,1.281 0.375,0.229 10 false A27 0.885,2.896 1.365,3.094 0.479,0.198 10 false 25 (S) 1.521,2.896 2.281,3.094 0.76,0.198 10 false 38 (SFTU) 2.583,2.896 3.271,3.094 0.688,0.198 10 false 27 (SFTD)

Disconnect the A27 ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A27-25 (S) - Body ground
·

Ignition switch ON

·

Shift lever in S, "+" and "-"


11 to 14 V
·

Ignition switch ON

·

Shift lever not in S, "+" and "-"


Below 1 V



c.

Turn the ignition switch off.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-38 (SFTU) - Body ground Shift lever continuously in "+"
(Up-shift)
Below 1 Ω
A27-27 (SFTD) - Body ground Shift lever continuously in "-"
(Down-shift)
Below 1 Ω
A27-38 (SFTU) - Body ground Shift lever in S 10 kΩ or higher
A27-27 (SFTD) - Body ground Shift lever in S 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR