Home › Drivetrain › JF3A TRANSFER / 4WD / AWD › TRANSFER ASSEMBLY
RM27L0U _52 Drivetrain _049312 JF3A TRANSFER / 4WD / AWD _0235672 TRANSFER ASSEMBLY G

JF3A TRANSFER / 4WD / AWD  TRANSFER ASSEMBLY  INSPECTION  


PROCEDURE

Hide 36211 1.INSPECT TRANSFER INPUT SHAFT

a.
C180912

Using a micrometer, measure the diameter of the transfer input shaft journal surface.

Minimum diameter:

68.002 mm (2.678 in.)


If the diameter is less than the minimum, replace the transfer input shaft.


b.
C180913

Using a dial indicator, measure the inside diameter of the transfer input shaft bimetal formed bush.

Maximum inside diameter:

46 mm (1.811 in.)


If the inside diameter is more than the maximum, replace the transfer input shaft.


Hide 36270 2.INSPECT TRANSFER LOW PLANETARY GEAR ASSEMBLY

a.
C180914

Using a feeler gauge, measure the thrust clearance of the pinion gear.

Standard clearance:

0.11 to 0.85 mm (0.00434 to 0.0334 in.)


Maximum clearance:

0.85 mm (0.0334 in.)


If the clearance is more than the maximum, replace the transfer low planetary gear assembly.


Hide 36270 3.INSPECT TRANSFER LOW PLANETARY GEAR ASSEMBLY

a.
C180915

Using a dial indicator, measure the radial clearance of the pinion gear.

Standard clearance:

0.011 to 0.038 mm (0.000434 to 0.00150 in.)


Maximum clearance:

0.038 mm (0.00150 in.)


If the clearance is more than the maximum, replace the transfer low planetary gear assembly.


Hide 36231 4.INSPECT REAR TRANSFER OUTPUT SHAFT

a.
C180916E01
0.587,1.53 0.706,1.690 0.119,0.161 10 A 1.59,1.558 1.709,1.714 0.119,0.156 10 B 2.306,1.581 2.444,1.728 0.137,0.147 10 C

Using a micrometer, measure the diameter of the rear transfer output shaft journal.

Minimum Diameter:
Journal Specified Condition
A 37.984 mm (1.496 in.)
B 41.984 mm (1.653 in.)
C 48.984 mm (1.928 in.)


If the diameter is less than the minimum, replace the rear transfer output shaft.


Hide 36311F 5.INSPECT NO. 1 TRANSFER GEAR SHIFT FORK AND FRONT DRIVE CLUTCH SLEEVE

a.
C183215

Using a feeler gauge, measure the clearance between the front drive clutch sleeve and No. 1 transfer gear shift fork.

Maximum clearance:

0.8 mm (0.0315 in.)


If the clearance is more than the maximum, replace the front drive clutch sleeve or No. 1 transfer gear shift fork.


Hide 36312F 6.INSPECT NO. 2 TRANSFER GEAR SHIFT FORK AND HIGH AND LOW CLUTCH SLEEVE

a.
C183216

Using a feeler gauge, measure the clearance between the transfer high and low clutch sleeve and No. 2 transfer gear shift fork.

Maximum clearance:

3 mm (0.118 in.)


If the clearance is more than the maximum, replace the transfer high and low clutch sleeve or No. 2 transfer gear shift fork.


Hide 36209 7.INSPECT TRANSFER SYNCHRONIZER RING SET

a.
C180917

Apply gear oil to the cone of the transfer drive sprocket sub-assembly, and check that it does not turn in both directions while pushing the transfer synchronizer ring set.

If it can turn, replace the transfer synchronizer ring set.


b.
C180918

Push the transfer synchronizer ring set to the cone of the transfer drive sprocket sub-assembly. Measure the clearance between the transfer synchronizer ring set and transfer drive sprocket sub-assembly.

Standard Clearance:

1.18 to 2.22 mm (0.0465 to 0.0874 in.)


Minimum Clearance:

1.18 mm (0.0465 in.)


If the clearance is not as specified, replace the transfer synchronizer ring set with a new one.