Home › Drivetrain › JF3A TRANSFER / 4WD / AWD › TRANSFER ASSEMBLY
RM27L0U _52 Drivetrain _049312 JF3A TRANSFER / 4WD / AWD _0235672 TRANSFER ASSEMBLY A

JF3A TRANSFER / 4WD / AWD  TRANSFER ASSEMBLY  DISASSEMBLY  


PROCEDURE

Hide 37109A 1.REMOVE HEAT INSULATOR BRACKET

a.
C180866

Remove the bolt and heat insulator bracket.


Hide 36111F 2.REMOVE TRANSFER CASE PLUG

a.
C180854E01
1.76,1.875 2.125,2.521 2.125,2.521 2.51,2.521 false 2.208,1.031 2.115,1.031 2.115,1.031 2.115,0.875 false 2.531,0.594 2.531,0.281 2.531,0.281 2.448,0.281 false 2.896,0.76 2.896,0.948 2.896,0.948 3,0.948 false 2.583,2.427 2.75,2.604 0.167,0.177 10 false *1 2.24,0.885 2.406,1.063 0.167,0.177 10 false *2 2.25,0.198 2.417,0.375 0.167,0.177 10 false *3 3.031,0.854 3.198,1.031 0.167,0.177 10 false *4

Using a 10 mm hexagon wrench, remove the transfer case plug, compression spring, ball and relief valve seat.

Text in Illustration
*1 Transfer Case Plug
*2 Compression Spring
*3 Ball
*4 Relief Valve Seat


Hide 36183A 3.REMOVE TRANSFER OIL PUMP PLATE

a.
C180849

Remove the 4 bolts and transfer oil pump plate.

NOTICE:

Do not drop the transfer oil pump drive rotor and transfer oil pump driven rotor.



b.
C180851

Remove the transfer oil seal ring from the transfer input shaft.


c.
C180850E02
1.484,0.7 1.209,0.331 1.209,0.331 0.676,0.331 false 0.44,0.241 0.613,0.414 0.173,0.173 10 *1 1.497,1.628 1.278,1.839 1.278,1.839 0.857,1.839 false 0.651,1.753 0.824,1.926 0.173,0.173 10 *2

Remove the transfer oil pump drive rotor and transfer oil pump driven rotor.

Text in Illustration
*1 Transfer Oil Pump Drive Rotor
*2 Transfer Oil Pump Driven Rotor


d.
C180856

Remove the O-ring from the transfer oil pump plate.


Hide 36111G 4.REMOVE TRANSFER CASE STRAIGHT PIN

a.
U153631

Remove the 2 transfer case straight pins.

NOTICE:

Do not drop the transfer case straight pin.



Hide 36111B 5.REMOVE TRANSFER OIL PUMP PLATE OIL SEAL

a.
C180855E01
1.155,0.418 1.304,0.836 1.304,0.836 1.418,0.836 false 1.476,0.733 1.678,0.926 0.202,0.193 10 *1

Using a screwdriver and hammer, tap out the transfer oil pump plate oil seal from the transfer oil pump plate.

Text in Illustration
*1 Protective Tape

NOTICE:

Be careful not to damage the transfer oil pump plate contact surfaces.



Hide 33309C 6.REMOVE FRONT OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY

a.
C180857E02
1.334,1.091 1.669,1.869 1.669,1.869 1.824,1.869 false 1.888,1.792 2.199,1.955 0.311,0.163 10 SST

Using SST and a hammer, loosen the staked part of the transfer output shaft nut.

SST
09930-00010  

NOTICE:
·

Be sure to use SST with the tapered surface facing the shaft.

·

Do not grind the tip of SST with a grinder or other device.

·

Completely loosen the staked part of the transfer output shaft nut when removing it.

·

Do not damage the threads of the driven sprocket.




b.
C270532E01
1.616,0.9 1.793,0.484 1.793,0.484 2.091,0.484 false 2.123,0.395 2.415,0.556 0.292,0.161 10 SST 3.12,1.235 3.301,1.395 0.181,0.161 10 *a 2.829,1.839 3.010,2.000 0.181,0.161 10 *b

Use SST to hold the front output shaft companion flange sub-assembly.

SST
09330-00021  

Text in Illustration
*a Hold
*b Turn


c.

Using a 32 mm socket wrench, remove the transfer output shaft nut.


d.
C180859

Remove the O-ring.


e.
C180860

Remove the front output shaft companion flange sub-assembly.


Hide 36102J 7.REMOVE TRANSFER CASE FRONT OIL SEAL

a.
C180928E02
1.574,2.489 1.574,2.924 1.574,2.924 1.723,2.924 false 1.752,2.838 2.060,3.003 0.309,0.165 10 SST

Using SST, remove the transfer case front oil seal from the front transfer case.

SST
09308-00010  

NOTICE:

Be careful not to damage the front transfer case contact surfaces.



Hide 33309C 8.REMOVE REAR OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY

a.
C180861E02
1.647,1.199 1.647,0.649 1.647,0.649 1.779,0.649 false 1.831,0.549 2.144,0.718 0.313,0.170 10 SST

Using SST and a hammer, loosen the staked part of the transfer output shaft nut.

SST
09930-00010  

NOTICE:
·

Be sure to use SST with the tapered surface facing the shaft.

·

Do not grind the tip of SST with a grinder or other device.

·

Completely loosen the staked part of the transfer output shaft nut when removing it.

·

Do not damage the threads of the rear transfer output shaft.




b.
C270533E01
1.67,0.887 1.872,0.418 1.872,0.418 2.435,0.418 false 2.491,0.332 2.806,0.481 0.316,0.149 10 SST 2.912,1.248 3.078,1.417 0.166,0.170 10 *a 2.254,1.836 2.421,2.006 0.166,0.170 10 *b

Use SST to hold the rear output shaft companion flange sub-assembly.

SST
09330-00021  

Text in Illustration
*a Hold
*b Turn


c.

Using a 32 mm socket wrench, remove the transfer output shaft nut.


d.
C180863

Remove the O-ring.


e.
C180864

Remove the rear output shaft companion flange sub-assembly.


Hide 36115C 9.REMOVE TRANSFER CASE REAR OIL SEAL

a.
C180929E02
1.331,1.972 1.331,2.406 1.331,2.406 1.438,2.406 false 1.468,2.32 1.777,2.472 0.309,0.152 10 SST

Using SST, remove the transfer case rear oil seal from the rear transfer case.

SST
09308-00010  

NOTICE:

Be careful not to damage the rear transfer case contact surfaces.



b.
C180930

Remove the 2 output washers.


Hide 36114B 10.REMOVE NO. 1 TRANSFER CASE PLUG

a.
C180865E01
1.417,0.135 1.698,0.135 false 1.469,0.438 1.75,0.438 false 1.573,0.771 1.844,0.771 false 1.75,0.042 1.906,0.208 0.156,0.167 10 false *1 1.802,0.344 1.958,0.51 0.156,0.167 10 false *2 1.896,0.677 2.052,0.844 0.156,0.167 10 false *3

Remove the No. 1 transfer case plug, compression spring and pin.

Text in Illustration
*1 No. 1 Transfer Case Plug
*2 Compression Spring
*3 Pin


Hide 36113C 11.REMOVE TRANSFER CASE PLUG

a.
C180867

Using a 6 mm hexagon wrench, remove the transfer case plug.


Hide 36112 12.REMOVE REAR TRANSFER CASE

a.
C180868

Remove the 14 bolts.


b.

Remove the rear transfer case.

HINT:

If necessary, tap the rear transfer case with a plastic-faced hammer to remove it.



Hide 36231E 13.REMOVE TRANSFER OUTPUT SHAFT FRONT NEEDLE ROLLER BEARING

a.
C270566

Remove the transfer output shaft front needle roller bearing from the rear output shaft assembly.


b.
C270567

Remove the spacer from the rear output shaft assembly.


Hide 36410J 14.REMOVE TRANSFER SHIFT ACTUATOR ASSEMBLY

a.
C180869

Using 2 screwdrivers and a hammer, tap out the 3 transfer gear shift fork shaft snap rings.


b.
C180870

Remove the 2 bolts.


c.
C180872

Remove the 3 bolts. Then remove the transfer shift actuator assembly, No. 1 transfer gear shift fork and No. 2 transfer gear shift fork from the rear output shaft assembly.


d.
C160356

Remove the O-ring from the transfer shift actuator assembly.


Hide 36235 15.REMOVE TRANSFER HIGH AND LOW CLUTCH SLEEVE

a.
C270568

Remove the transfer high and low clutch sleeve from the rear output shaft assembly.


Hide 16.REMOVE REAR OUTPUT SHAFT ASSEMBLY

a.
C270569

Using a snap ring expander, expand the rear transfer output shaft snap ring.


b.
C270570

Using a plastic-faced hammer, carefully tap the case rear, and remove the rear output shaft assembly together with the drive chain and driven sprocket.


c.

Remove the rear output shaft assembly and driven sprocket from the drive chain.


d.
C180880

Using a snap ring expander, remove the rear transfer output shaft snap ring from the rear transfer case.


Hide 41335D 17.REMOVE SIDE GEAR SHAFT HOLDER BEARING

a.
U153898E01
0.932,0.96 0.285,0.585 0.285,0.585 0.841,1.115 false 0.403,0.138 0.700,0.296 0.297,0.158 10 SST

Using SST and a press, remove the side gear shaft holder bearing.

SST
09950-00020  
09950-60010  (09951-00380)
09950-70010  (09951-07150)


Hide 36104K 18.REMOVE TRANSFER OIL SEPARATOR SUB-ASSEMBLY

a.
C180884

Remove the 3 bolts and transfer oil separator sub-assembly.


b.
C180885

Remove the O-ring from the transfer oil separator sub-assembly.


Hide 33449D 19.REMOVE TRANSFER CASE MAGNET

a.
C180886

Remove the transfer case magnet.


Hide 20.REMOVE INPUT SHAFT ASSEMBLY

a.
C180887

Using a 14 mm hexagon wrench, remove the 2 transfer case plugs from the front transfer case.


b.
C180888

Expand the transfer input shaft hole snap ring. Then remove the input shaft assembly from the front transfer case.


Hide 36273 21.REMOVE TRANSFER LOW PLANETARY RING GEAR

a.

Using a snap ring expander, remove the transfer low planetary ring gear hole snap ring.


b.
C180892

Remove the transfer low planetary ring gear from the front transfer case.


c.
C180891

Using a screwdriver, remove the transfer input shaft hole snap ring from the front transfer case.


Hide 36292A 22.REMOVE TRANSFER DRIVEN SPROCKET BEARING

a.
C180893E01
2.172,0.935 2.476,1.087 0.304,0.151 10 SST 1.648,1.017 2.154,1.017 2.154,1.017 1.757,1.405 false

Using SST, remove the transfer driven sprocket bearing from the front transfer case.

SST
09950-60020  (09951-00680)
09950-70010  (09951-07150)


Hide 36216A 23.REMOVE NO. 1 TRANSFER INPUT SHAFT SEAL RING

a.
C162486

Remove the No. 1 transfer input shaft seal ring from the transfer input shaft.


Hide 36210A 24.REMOVE TRANSFER INPUT SHAFT BEARING

a.
C159629

Using a snap ring expander, remove the transfer input shaft snap ring.


b.
C270535E01
0.708,1.985 0.896,2.168 0.188,0.184 10 *a 3.14,1.074 3.328,1.258 0.188,0.184 10 *b 0.585,2.818 0.908,2.984 0.323,0.165 10 SST 1.722,2.162 1.175,2.896 1.175,2.896 1.021,2.896 false 1.776,2.761 1.175,2.896 1.175,2.896 2.131,2.329 false

Using SST and a press, pull out the transfer input shaft bearing.

SST
09555-55010  
09950-00030  
09950-60010  (09951-00480)

Text in Illustration
*a Hold
*b Turn

NOTICE:

Be careful not to drop or damage the transfer low planetary gear assembly.



c.

Remove the transfer low planetary gear assembly and 2 transfer low planetary gear bearings from the transfer input shaft.


Hide 36211 25.REMOVE TRANSFER INPUT SHAFT BIMETAL FORMED BUSH

a.
C173631E01
1.581,0.125 2.035,0.302 0.454,0.177 10 SST 1.159,0.775 1.314,0.2 false 1.314,0.2 1.541,0.2 false

Using SST, remove the transfer input shaft bimetal formed bush.

SST
09387-00041  (09387-01021, 09387-01030, 09387-01041)


Hide 36218C 26.REMOVE TRANSFER INPUT SHAFT PLUG

a.
C173494E01
2.908,0.911 3.202,1.101 0.295,0.191 10 SST 2.599,1.205 2.852,0.999 false 2.852,0.999 2.625,1.743 false

Using SST and a hammer, tap out the transfer input shaft plug.

SST
09950-70010  (09951-07150)
09950-60010  (09951-00350)


Hide 36255 27.REMOVE NO. 1 TRANSFER OUTPUT SHAFT SPACER

a.
C270536

Using 2 screwdrivers, tap out the snap ring.


b.
C270537

Remove the No. 1 transfer output shaft spacer from the rear transfer output shaft.


c.
C173604E01
2.296,0.52 2.554,0.258 2.554,0.258 2.799,0.258 false 1.243,1.71 1.048,1.906 1.048,1.906 0.857,1.906 false 0.625,1.817 0.784,1.977 0.159,0.159 10 *1 2.842,0.167 3.001,0.327 0.159,0.159 10 *2

Remove the seal ring from the No. 1 transfer output shaft spacer.

Text in Illustration
*1 Seal Ring
*2 No. 1 Transfer Output Shaft Spacer


Hide 41311M 28.REMOVE CENTER DIFFERENTIAL CASE

a.
C270538

Remove the straight pin from the rear transfer output shaft.


b.

Remove the center differential case from the rear transfer output shaft.


Hide 36236 29.REMOVE FRONT DRIVE CLUTCH SLEEVE

a.
U153634

Remove the front drive clutch sleeve with the transfer synchronizer ring set, 2 shifting key snap rings, 3 shifting keys and transfer clutch hub from the rear transfer output shaft.


b.
U153633

Remove the 2 transfer clutch hub bearings from the rear transfer output shaft.


c.
C180927E01
1.872,0.237 2.047,0.416 0.174,0.179 10 *1

Remove the transfer synchronizer ring set from the front drive clutch sleeve.

Text in Illustration
*1 Transfer Synchronizer Ring Set


d.
C180907E02
0.993,0.924 0.764,0.689 0.764,0.689 0.513,0.689 false 2.386,1.325 2.616,1.56 2.616,1.56 2.866,1.56 false 0.311,0.61 0.470,0.773 0.159,0.163 10 *1 2.915,1.457 3.074,1.619 0.159,0.163 10 *1 0.779,0.039 0.939,0.201 0.159,0.163 10 *2 2.46,1.104 2.689,0.869 2.689,0.869 2.939,0.869 false 3.009,0.769 3.169,0.932 0.159,0.163 10 *2 1.186,1.557 0.957,1.792 0.957,1.792 0.706,1.792 false 0.457,1.701 0.617,1.864 0.159,0.163 10 *2 1.478,0.365 1.249,0.13 1.249,0.13 0.999,0.13 false

Using a screwdriver, remove the 2 shifting key snap rings and 3 shifting keys from the front drive clutch sleeve.

Text in Illustration
*1 Shifting Key Snap Ring
*2 Shifting Key


e.
C180908

Remove the transfer clutch hub from the front drive clutch sleeve.


Hide 36231 30.REMOVE REAR TRANSFER OUTPUT SHAFT

a.
C270571E01
1.064,1.833 1.262,1.833 1.262,1.833 1.494,2.254 false 0.643,1.751 0.952,1.904 0.309,0.152 10 SST

Using SST and a press, press out the bearing.

SST
09950-00020  

NOTICE:

Be careful not to drop or damage the rear transfer output shaft.



b.
C180910

Remove the transfer drive sprocket sub-assembly from the rear transfer output shaft.


c.
C180911

Remove the needle roller bearing from the rear transfer output shaft.