Home › Drivetrain › JF3A TRANSFER / 4WD / AWD › TRANSFER ASSEMBLY
RM27L0U _52 Drivetrain _049312 JF3A TRANSFER / 4WD / AWD _0235672 TRANSFER ASSEMBLY A

JF3A TRANSFER / 4WD / AWD  TRANSFER ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Coat all of the sliding and rotating surfaces with gear oil before reassembly.


PROCEDURE

Hide 36231 1.INSTALL REAR TRANSFER OUTPUT SHAFT

a.
C180911

Install a new needle roller bearing.


b.
C180910

Install the transfer drive sprocket sub-assembly.


c.
C180919E02
0.915,2.696 0.765,1.526 0.765,1.526 0.599,1.526 false 0.985,1.684 0.765,1.526 false 0.188,1.459 0.503,1.615 0.316,0.156 10 SST

Using SST and a press, press in a new bearing.

SST
09308-14010  
09316-20011  

NOTICE:

Make sure the bearing is installed in the correct direction.



Hide 36236 2.INSTALL FRONT DRIVE CLUTCH SLEEVE

a.
C180908

Install the transfer clutch hub onto the front drive clutch sleeve.


b.
C180907E02
0.993,0.924 0.764,0.689 0.764,0.689 0.513,0.689 false 2.386,1.325 2.616,1.56 2.616,1.56 2.866,1.56 false 0.311,0.61 0.470,0.773 0.159,0.163 10 *1 2.915,1.457 3.074,1.619 0.159,0.163 10 *1 0.779,0.039 0.939,0.201 0.159,0.163 10 *2 2.46,1.104 2.689,0.869 2.689,0.869 2.939,0.869 false 3.009,0.769 3.169,0.932 0.159,0.163 10 *2 1.186,1.557 0.957,1.792 0.957,1.792 0.706,1.792 false 0.457,1.701 0.617,1.864 0.159,0.163 10 *2 1.478,0.365 1.249,0.13 1.249,0.13 0.999,0.13 false

Install the 3 shifting keys and 2 shifting key snap rings.

Text in Illustration
*1 Shifting Key Snap Ring
*2 Shifting Key

NOTICE:

Install the shifting key snap ring so that their end gaps are not in line.



c.

Apply transfer oil to the transfer synchronizer ring set.


d.
C180927E01
1.872,0.237 2.047,0.416 0.174,0.179 10 *1

Install the transfer synchronizer ring set.

Text in Illustration
*1 Transfer Synchronizer Ring Set

NOTICE:

Align the slots of the synchronizer outer with the inner rings.



e.
U153633

Install the 2 transfer clutch hub bearings.


f.
C180920

Install the front drive clutch sleeve with the synchronizer ring set, 2 shifting key snap rings, 3 shifting keys and transfer clutch hub onto the rear transfer output shaft.

NOTICE:

Align the cutouts in the transfer drive sprocket sub-assembly with the protrusions on the center synchronizer ring.



Hide 41311M 3.INSTALL CENTER DIFFERENTIAL CASE

a.
C270538

Install the center differential case to the rear transfer output shaft.


b.

Install the straight pin to the rear transfer output shaft.


Hide 36255 4.INSTALL NO. 1 TRANSFER OUTPUT SHAFT SPACER

a.

Apply transfer oil to a new seal ring.


b.
C173604E01
2.296,0.52 2.554,0.258 2.554,0.258 2.799,0.258 false 1.243,1.71 1.048,1.906 1.048,1.906 0.857,1.906 false 0.625,1.817 0.784,1.977 0.159,0.159 10 *1 2.842,0.167 3.001,0.327 0.159,0.159 10 *2

Install the seal ring to the No. 1 transfer output shaft spacer.

Text in Illustration
*1 Seal Ring
*2 No. 1 Transfer Output Shaft Spacer


c.
C270539

Align the straight pin with the straight pin groove of the No. 1 transfer output shaft spacer, and slide on the No. 1 transfer output shaft spacer.


d.
C270540

Using a screwdriver and hammer, tap on the snap ring.


Hide 36218C 5.INSTALL TRANSFER INPUT SHAFT PLUG

a.
C180921E02
2.94,2.84 3.246,2.989 0.305,0.149 10 SST 2.777,2.568 3.091,2.84 3.091,2.84 2.659,2.161 false 0.715,4.116 0.843,4.269 0.128,0.152 10 A

Using SST and a hammer, tap in a new transfer input shaft plug as shown in the illustration.

SST
09950-70010  (09951-07150)
09950-60010  (09951-00380)

Drive in depth (A):

1.0 to 1.8 mm (0.0394 to 0.0708 in.)


NOTICE:

Be careful not to damage or deform the transfer input shaft plug when tapping it.



Hide 36211 6.INSTALL TRANSFER INPUT SHAFT BIMETAL FORMED BUSH

a.
C173632E02
1.677,0.693 1.992,0.887 0.316,0.194 10 SST 0.932,3.847 1.056,4.012 0.123,0.165 10 A 2.058,0.782 2.19,0.782 2.19,0.782 2.395,0.987 false 2.284,1.3 2.19,0.782 false

Using SST and a hammer, tap in a new transfer input shaft bimetal formed bush as shown in the illustration.

SST
09950-70010  (09951-07150)
09950-60010  (09951-00600)

Drive in depth (A):

5.5 to 5.9 mm (0.217 to 0.232 in.)


NOTICE:

Be careful not to damage the transfer input shaft.



Hide 36210A 7.INSTALL TRANSFER INPUT SHAFT BEARING

a.
C353571E01
1.979,0.875 2.302,0.875 true 1.042,2.979 1.146,3.198 1.146,3.198 1.271,3.198 true 1.74,2.615 1.833,2.927 1.833,2.927 1.948,2.927 true 2.531,2.521 2.667,2.938 2.667,2.938 2.792,2.938 true 1.792,0.781 2.104,0.979 0.313,0.198 10 false *a 1.365,3.125 1.677,3.323 0.313,0.198 10 false *2 1.979,2.823 2.292,3.021 0.313,0.198 10 false *1 2.854,2.823 3.167,3.021 0.313,0.198 10 false *3

Install the transfer low planetary gear bearing and transfer low planetary gear assembly to the transfer input shaft.

NOTICE:
·

Make sure that the transfer low planetary gear bearing is installed in the correct direction.

·

Install the transfer low planetary gear bearing so that its temper color side faces the transfer low planetary gear assembly.



Text in Illustration
*1 Transfer Low Planetary Gear Bearing
*2 Transfer Low Planetary Gear Assembly
*3 Transfer Input Shaft
*a Temper Color Side


b.
C173498E02
2.232,0.71 2.232,1.381 2.232,1.381 2.427,1.381 false 2.495,1.283 2.684,1.444 0.188,0.161 10 *a 1.143,0.258 1.201,0.143 1.201,0.143 1.298,0.143 false 1.332,0.074 1.521,0.235 0.188,0.161 10 *2 0.53,0.63 0.473,0.515 0.473,0.515 0.376,0.515 false 0.164,0.424 0.352,0.584 0.188,0.161 10 *1 0.53,1.14 0.473,1.025 0.473,1.025 0.376,1.025 false 0.164,0.934 0.352,1.094 0.188,0.161 10 *3

Install the transfer low planetary gear bearing and a new transfer input shaft bearing to the transfer input shaft.

Text in Illustration
*1 Transfer Low Planetary Gear Bearing
*2 Transfer Input Shaft Bearing
*3 Transfer Low Planetary Gear Assembly
*a Temper Color Side

NOTICE:
·

Make sure that the transfer input shaft bearing is installed in the correct direction.

·

Make sure that the transfer low planetary gear bearing is installed in the correct direction.

·

Install the transfer low planetary gear bearing so that its temper color side faces the transfer low planetary gear assembly.




c.
C180922E02
1.015,1.246 1.308,0.24 1.308,0.24 1.531,0.24 false 1.6,0.163 1.915,0.319 0.316,0.156 10 SST 0.904,3.979 1.144,4.32 1.144,4.32 1.368,4.32 false 1.452,4.219 1.768,4.375 0.316,0.156 10 SST

Using SST and a press, press in the transfer input shaft bearing.

SST
09513-36040  
09950-60020  (09951-00720)

NOTICE:

After press-fitting the transfer input shaft bearing to the transfer input shaft, check that the transfer input shaft bearing moves smoothly.



d.
C159629

Select a transfer input shaft snap ring that allows for minimum axial play and install it to the transfer input shaft.

Snap Ring Thickness:
Mark Thickness
C 2.13 to 2.18 mm (0.0839 to 0.0858 in.)
D 2.18 to 2.23 mm (0.0859 to 0.0877 in.)
E 2.23 to 2.28 mm (0.0878 to 0.0897 in.)
F 2.28 to 2.33 mm (0.0898 to 0.0917 in.)
G 2.33 to 2.38 mm (0.0918 to 0.0937 in.)
H 2.38 to 2.43 mm (0.0938 to 0.0956 in.)
J 2.43 to 2.48 mm (0.0957 to 0.0976 in.)



e.

Using a snap ring expander, install the transfer input shaft snap ring.

NOTICE:

Make sure that the snap ring is firmly installed to the groove.



Hide 36216A 8.INSTALL NO. 1 TRANSFER INPUT SHAFT SEAL RING

a.
C162486

Apply transfer oil to a new No. 1 transfer input shaft seal ring.


b.

Install the No. 1 transfer input shaft seal ring to the transfer input shaft.


Hide 36292A 9.INSTALL TRANSFER DRIVEN SPROCKET BEARING

a.
C180923E01
1.746,1.316 2.061,0.989 2.061,0.989 2.147,0.989 false 1.816,1.768 2.061,0.989 false 2.19,0.909 2.492,1.061 0.302,0.152 10 SST

Install a new transfer driven sprocket bearing to the front transfer case in the direction shown in the illustration.

SST
09950-60020  (09951-00790)
09950-70010  (09951-07150)

NOTICE:

Make sure that the transfer driven sprocket bearing is installed in the correct direction.



Hide 36273 10.INSTALL TRANSFER LOW PLANETARY RING GEAR

a.
C180891

Install the transfer input shaft hole snap ring to the front transfer case.


b.
F043457E06
0.853,0.497 1.024,0.698 0.171,0.201 10 *a

Install the transfer low planetary ring gear to the front transfer case.

Text in Illustration
*a Front

NOTICE:

Make sure to install the transfer low planetary ring gear in the correct direction.



c.
C173488

Using a screwdriver, install the transfer low planetary ring gear hole snap ring.

NOTICE:

Make sure that the transfer low planetary ring gear hole snap ring is firmly installed to the groove.



Hide 11.INSTALL INPUT SHAFT ASSEMBLY

a.
C180888

While expanding the transfer input shaft hole snap ring, install the input shaft assembly to the front transfer case.


b.
C180887

Clean the threads of the 2 transfer case plugs and the front transfer case with non-residue solvent.


c.

Apply adhesive to the threads of the 2 transfer case plugs.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


NOTICE:

Install the transfer case plug within 3 minutes of application.



d.

Using a 14 mm hexagon wrench, install the 2 transfer case plugs.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 33449D 12.INSTALL TRANSFER CASE MAGNET

a.
C180886

Install the transfer case magnet.


Hide 36104K 13.INSTALL TRANSFER OIL SEPARATOR SUB-ASSEMBLY

a.
C353572

Install a new O-ring.


b.
C180884

Install the transfer oil separator sub-assembly with the 3 bolts.

Torque:
18 N*m (178 kgf*cm, 13 ft.*lbf)


Hide 41335D 14.INSTALL SIDE GEAR SHAFT HOLDER BEARING

a.
C273276E01
0.927,0.616 0.703,0.307 0.703,0.307 0.583,0.307 false 0.153,0.227 0.476,0.401 0.323,0.174 10 SST

Using SST and a press, install a new side gear shaft holder bearing.

SST
09214-60010  

NOTICE:

Press in the side gear shaft holder bearing until they fit to the edge.



Hide 15.INSTALL REAR OUTPUT SHAFT ASSEMBLY

a.
C180880

Install the rear transfer output shaft snap ring to the rear transfer case.


b.

Fix the rear transfer case in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



c.
C274079

Install the rear output shaft assembly, drive chain and driven sprocket to the rear transfer case.

NOTICE:

Do not drop the front drive clutch sleeve or shifting keys.



d.
C270569

Using a snap ring expander, install the rear transfer output shaft snap ring to the rear output shaft assembly.

NOTICE:

Make sure that the rear transfer output shaft snap ring is firmly installed to the groove.



Hide 36235 16.INSTALL TRANSFER HIGH AND LOW CLUTCH SLEEVE

a.
C270568

Install the transfer high and low clutch sleeve to the rear output shaft assembly.


Hide 36410J 17.INSTALL TRANSFER SHIFT ACTUATOR ASSEMBLY

a.
C353573

Install a new O-ring to the transfer shift actuator assembly.


b.
C180872

Set the No. 1 transfer gear shift fork and No. 2 transfer gear shift fork to the rear output shaft assembly. Then install the transfer shift actuator assembly to the rear transfer case with the 3 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


c.
C180870

Install the 2 bolts.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


d.
C270572

Install the 3 transfer gear shift fork shaft snap rings into the transfer shift actuator assembly.


Hide 36231E 18.INSTALL TRANSFER OUTPUT SHAFT FRONT NEEDLE ROLLER BEARING

a.
C270567

Install the spacer.


b.

Apply transfer oil to the transfer output shaft front needle roller bearing.


c.
C270566

Install the transfer output shaft front needle roller bearing to the rear output shaft assembly.


Hide 36112 19.INSTALL REAR TRANSFER CASE

a.
C160517E03
1.573,0.563 1.573,0.167 1.573,0.167 1.698,0.167 false 1.74,0.073 1.896,0.229 0.156,0.156 10 false *1

Apply seal packing to the rear transfer case as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


Text in Illustration
*1 Seal Packing

NOTICE:

If the removed rear transfer case will be reused: After removing the rear transfer case, perform the following before reinstalling it: 1) using a knife, cut off any old FIPG on the rear transfer case's contact surface, 2) clean off any remaining old FIPG from the rear transfer case's contact surface, and 3) reapply seal packing to the rear transfer case.



b.
C180868

Install the rear transfer case with the 14 bolts.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

NOTICE:

Tighten the bolts of the rear transfer case within 10 minutes of applying the seal packing. The seal packing will dry very quickly.



Hide 36113C 20.INSTALL TRANSFER CASE PLUG

a.

Clean the threads of the transfer case plug and the front transfer case with non-residue solvent.


b.
C180867

Apply adhesive to the threads of the transfer case plug.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


NOTICE:

Install the transfer case plug within 3 minutes of application.



c.

Using a 6 mm hexagon wrench, install the transfer case plug.

Torque:
39 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 36114B 21.INSTALL NO. 1 TRANSFER CASE PLUG

a.
C180865E01
1.417,0.135 1.698,0.135 false 1.469,0.438 1.75,0.438 false 1.573,0.771 1.844,0.771 false 1.75,0.042 1.906,0.208 0.156,0.167 10 false *1 1.802,0.344 1.958,0.51 0.156,0.167 10 false *2 1.896,0.677 2.052,0.844 0.156,0.167 10 false *3

Clean the threads of the No. 1 transfer case plug and the front transfer case with non-residue solvent.


b.

Apply adhesive to the threads of the No. 1 transfer case plug.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


NOTICE:

Install the No. 1 transfer case plug within 3 minutes of application.



c.

Install the pin, compression spring and No. 1 transfer case plug to the front transfer case.

Torque:
No. 1 Transfer Case Plug : 19 N*m (190 kgf*cm, 14 ft.*lbf)

Text in Illustration
*1 No. 1 Transfer Case Plug
*2 Compression Spring
*3 Pin


Hide 36102J 22.INSTALL TRANSFER CASE FRONT OIL SEAL

a.

Apply transfer oil to the spline area of the driven sprocket.


b.
C159301E02
1.419,0.142 1.706,0.323 0.287,0.181 10 SST 1.775,0.232 1.981,0.232 false 1.981,0.232 1.981,0.596 false 2.467,1.707 2.581,1.856 0.114,0.149 10 A

Using SST and a hammer, tap in a new transfer case front oil seal as shown in the illustration.

SST
09316-60011  (09316-00011)

Drive in depth (A):

1.0 to 1.5 mm (0.0394 to 0.0590 in.)



Hide 33309C 23.INSTALL FRONT OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY

a.

Install the front output shaft companion flange sub-assembly onto the driven sprocket.


b.
C270542E01
3.102,1.593 3.277,1.753 0.174,0.161 10 *a 2.753,0.659 2.927,0.819 0.174,0.161 10 *b 2.025,1.415 2.025,1.77 2.025,1.77 1.836,1.77 false 1.458,1.69 1.762,1.865 0.304,0.174 10 SST

Use SST to hold the front output shaft companion flange sub-assembly.

SST
09330-00021  


c.

Using a 32 mm socket wrench, install a new O-ring and a new transfer output shaft nut.

Torque:
112 N*m (1137 kgf*cm, 82 ft.*lbf)

Text in Illustration
*a Hold
*b Turn


d.
F050151E03
0.802,0.25 1,0.448 0.198,0.198 10 false *a 0.802,1.885 0.99,2.083 0.188,0.198 10 false *b

Using a chisel and hammer, stake the transfer output shaft nut.

Text in Illustration
*a Correct
*b Incorrect


Hide 36115C 24.INSTALL TRANSFER CASE REAR OIL SEAL

a.
C180930

Install the 2 output washers.


b.

Apply transfer oil to the spline area of the rear transfer output shaft.


c.
C159303E01
2.031,0.255 2.318,0.436 0.287,0.181 10 SST 1.985,0.357 1.759,0.919 false 1.985,0.357 1.292,0.82 false

Using SST and a hammer, tap in a new transfer case rear oil seal until its surface is flush with the housing upper surface.

SST
09316-60011  (09316-00011)


Hide 33309C 25.INSTALL REAR OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY

a.

Install the rear output shaft companion flange sub-assembly onto the rear transfer output shaft.


b.
C270543E01
2.673,1.799 2.852,1.964 0.179,0.165 10 *a 2.847,0.693 3.027,0.858 0.179,0.165 10 *b 0.977,1.593 1.286,1.753 0.309,0.161 10 SST 1.384,1.682 1.498,1.682 1.498,1.682 1.498,1.398 false

Use SST to hold the rear output shaft companion flange sub-assembly.

SST
09330-00021  


c.

Using a 32 mm socket wrench, install a new O-ring and a new transfer output shaft nut.

Torque:
112 N*m (1137 kgf*cm, 82 ft.*lbf)

Text in Illustration
*a Hold
*b Turn


d.
F050151E03
0.802,0.25 1,0.448 0.198,0.198 10 false *a 0.802,1.885 0.99,2.083 0.188,0.198 10 false *b

Using a chisel and hammer, stake the transfer output shaft nut.

Text in Illustration
*a Correct
*b Incorrect


Hide 36111B 26.INSTALL TRANSFER OIL PUMP PLATE OIL SEAL

a.
U153503E01
1.26,0.542 1.5,0.177 1.5,0.177 1.635,0.177 false 1.396,0.76 1.51,0.177 false 3.115,0 3.417,0 false 2.417,0.792 2.417,1.094 false 1.667,0.104 2.031,0.323 0.365,0.219 10 false SST 2.49,0.719 2.792,0.854 0.302,0.135 10 false A

Using SST and a hammer, tap in a new transfer oil pump plate oil seal as shown in the illustration.

SST
09950-70010  (09951-07100)
09950-60010  (09951-00630)

Drive in depth (A):

0.5 mm or less (0.0196 in. or less)


NOTICE:

Be careful not to damage the transfer oil pump plate.



Hide 36111G 27.INSTALL TRANSFER CASE STRAIGHT PIN

a.
U153631

Install the 2 transfer case straight pins to the transfer input shaft.


Hide 36183A 28.INSTALL TRANSFER OIL PUMP PLATE

a.
C180856

Apply transfer oil to a new O-ring, transfer oil pump drive rotor, transfer oil pump driven rotor and a new transfer oil seal ring.


b.

Install the O-ring.


c.
C180850E02
1.484,0.7 1.209,0.331 1.209,0.331 0.676,0.331 false 0.44,0.241 0.613,0.414 0.173,0.173 10 *1 1.497,1.628 1.278,1.839 1.278,1.839 0.857,1.839 false 0.651,1.753 0.824,1.926 0.173,0.173 10 *2

Install the transfer oil pump drive rotor and transfer oil pump driven rotor.

Text in Illustration
*1 Transfer Oil Pump Drive Rotor
*2 Transfer Oil Pump Driven Rotor


d.
C180851

Install the transfer oil seal ring to the transfer input shaft.


e.
C180849

Install the transfer oil pump plate with the 4 bolts.

Torque:
12 N*m (117 kgf*cm, 8 ft.*lbf)


Hide 36111F 29.INSTALL TRANSFER CASE PLUG

a.
C180854E01
1.76,1.875 2.125,2.521 2.125,2.521 2.51,2.521 false 2.208,1.031 2.115,1.031 2.115,1.031 2.115,0.875 false 2.531,0.594 2.531,0.281 2.531,0.281 2.448,0.281 false 2.896,0.76 2.896,0.948 2.896,0.948 3,0.948 false 2.583,2.427 2.75,2.604 0.167,0.177 10 false *1 2.24,0.885 2.406,1.063 0.167,0.177 10 false *2 2.25,0.198 2.417,0.375 0.167,0.177 10 false *3 3.031,0.854 3.198,1.031 0.167,0.177 10 false *4

Clean the threads of the transfer case plug and the transfer oil pump plate with non-residue solvent.

Text in Illustration
*1 Transfer Case Plug
*2 Compression Spring
*3 Ball
*4 Relief Valve Seat


b.

Apply adhesive to the threads of the transfer case plug.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



c.

Install the relief valve seat, ball and compression spring to the transfer oil pump plate.


d.

Using a 10 mm hexagon wrench, install the transfer case plug.

Torque:
29 N*m (300 kgf*cm, 22 ft.*lbf)


Hide 37109A 30.INSTALL HEAT INSULATOR BRACKET

a.
C180866

Install the heat insulator bracket with the bolt.

NOTICE:

Position the heat insulator bracket against the front transfer case rib so that it will not rotate.


Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)