Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY
RM27L0U _52 Drivetrain _049313 DRIVE SHAFT / PROPELLER SHAFT _0235681 FRONT DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY  DISASSEMBLY  


PROCEDURE

Hide 43411C 1.REMOVE FRONT DRIVE INNER SHAFT OUTER SHAFT SNAP RING

a.
C057543

Using a screwdriver, remove the shaft snap ring.

NOTICE:

Do not damage the spline of the inboard joint shaft.



Hide 43448A 2.REMOVE FRONT AXLE NO. 1 INBOARD JOINT BOOT SETTING CLAMP

a.

Using a side cutter, cut the No. 1 inboard joint boot setting clamp and remove it.


Hide 43448B 3.REMOVE FRONT AXLE NO. 2 INBOARD JOINT BOOT SETTING CLAMP

a.

Using a side cutter, cut the No. 2 inboard joint boot setting clamp and remove it.


Hide 04438A 4.DISCONNECT FRONT DRIVE SHAFT INBOARD JOINT BOOT

a.
C353596

Disconnect the inboard joint boot from the inboard joint shaft.


Hide 5.REMOVE FRONT DRIVE SHAFT INBOARD JOINT SHAFT ASSEMBLY

a.
C115632E08
1.885,0.646 1.188,0.229 1.188,0.229 1.521,1.031 false 0.396,0.094 1.198,0.271 0.802,0.177 10 false Matchmarks

Place matchmarks on the inboard joint shaft and inboard joint shaft.

NOTICE:

Do not punch the marks.



b.

Using a screwdriver, remove the snap ring from the outboard joint shaft.


c.

Remove the inboard joint shaft from the outboard joint shaft.


d.
C115633E09
2.573,1.271 2.104,0.125 2.104,0.125 2.458,1.354 false 2.104,0.125 2.406,1.469 false 1.302,0.042 2.104,0.219 0.802,0.177 10 false Matchmarks

Place matchmarks on the outboard joint shaft, inner race and cage.

NOTICE:

Do not punch the marks.



e.

Remove the 6 balls.


f.

Slide the cage to the outboard joint side.


g.
C158392

Using a snap ring expander, remove the snap ring.


h.
C158393

Using a brass bar and hammer, tap out the inner race.

NOTICE:

Be careful not to damage the inner race.



i.

Remove the cage.


Hide 04438A 6.REMOVE FRONT DRIVE SHAFT INBOARD JOINT BOOT

a.

Remove the inboard joint boot from the outboard joint shaft.


Hide 43447A 7.REMOVE FRONT AXLE NO. 1 OUTBOARD JOINT BOOT SETTING CLAMP

a.

Using a side cutter, cut the No. 1 outboard joint boot setting clamp and remove it.


Hide 43447B 8.REMOVE FRONT AXLE NO. 2 OUTBOARD JOINT BOOT SETTING CLAMP

a.

Using a side cutter, cut the No. 2 outboard joint boot setting clamp and remove it.


Hide 04438 9.REMOVE FRONT DRIVE SHAFT OUTBOARD JOINT BOOT

a.

Remove the outboard joint boot from the outboard joint shaft.


Hide 41336E 10.REMOVE FRONT DRIVE SHAFT DUST COVER

a.
C124194E02
1.206,0.924 0.845,0.449 false 0.463,0.357 0.761,0.517 0.298,0.160 10 SST

Using SST and a press, press out the dust cover from the inboard joint shaft.

SST
09950-00020  

NOTICE:

Do not drop the inboard joint shaft.



Hide 43502K 11.REMOVE FRONT AXLE DUST SEAL

a.
C124193E02
1.391,0.763 0.855,0.38 false 0.443,0.288 0.747,0.467 0.304,0.179 10 SST

Using SST and a press, press out the dust seal from the outboard joint shaft assembly.

SST
09950-00020  

NOTICE:

Do not drop the outboard joint shaft assembly.