Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY
RM27L0U _52 Drivetrain _049313 DRIVE SHAFT / PROPELLER SHAFT _0235681 FRONT DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY  REASSEMBLY  


PROCEDURE

Hide 43502K 1.INSTALL FRONT AXLE DUST SEAL

a.
C115634E02
0.513,1.239 0.822,1.427 0.309,0.188 10 SST 1.266,1.685 0.874,1.331 false

Using SST and a press, press in a new dust seal to the outboard joint shaft assembly.

SST
09950-00020  

NOTICE:

Be careful not to damage the dust seal.



Hide 41336E 2.INSTALL FRONT DRIVE SHAFT DUST COVER

a.
C115635E02
1.313,0.771 1.781,0.219 false 0.51,1.875 0.74,1.552 false 1.823,0.094 2.604,0.281 0.781,0.188 10 false Steel Plate 0.198,1.844 0.51,2.042 0.313,0.198 10 false SST

Using SST, a steel plate and press, press in a new dust cover to the inboard joint shaft.

SST
09316-20011  

NOTICE:

Be careful not to damage the dust cover.



Hide 04438 3.INSTALL FRONT DRIVE SHAFT OUTBOARD JOINT BOOT

a.

Wrap the spline of the outboard joint shaft with vinyl tape to prevent the boots from being damaged.


b.

Install the new outboard joint boot to the outboard joint shaft.


c.

Pack the outboard joint shaft and boot with grease from the boot kit.

Standard grease capacity:

292 to 312 g (10.3 to 11.0 oz.)



d.

Install the outboard joint boot into the groove on the outboard joint shaft.

NOTICE:

Keep the groove where you are fitting the boot free of grease.



Hide 43447B 4.INSTALL FRONT AXLE NO. 2 OUTBOARD JOINT BOOT SETTING CLAMP

a.

Install the No. 2 outboard joint boot setting clamp onto the outboard joint boot.


b.
C115638E01
0.874,0.454 1.238,0.652 0.364,0.198 10 SST 2.155,1.064 1.304,0.617 false

Using SST, pinch the clamp.

SST
09521-24010  

NOTICE:

Do not overtighten SST.



Hide 43447A 5.INSTALL FRONT AXLE NO. 1 OUTBOARD JOINT BOOT SETTING CLAMP

a.

Install the No. 1 outboard joint boot setting clamp onto the outboard joint boot.


b.
C115637E01
0.186,0.282 0.509,0.452 0.323,0.170 10 SST 1.77,1.194 0.565,0.471 false

Using SST, pinch the clamp.

SST
09521-24010  

NOTICE:

Do not overtighten SST.



Hide 6.INSPECT AND ADJUST FRONT AXLE OUTBOARD JOINT BOOT SETTING CLAMP

a.
C162200E05
1.781,1.427 1.229,1.531 false 0.927,1.469 1.271,1.656 0.344,0.188 10 false SST 0.865,0.531 1.208,0.719 0.344,0.188 10 false (A)

Using SST, inspect and adjust the clearance of the boot setting clamps.

SST
09240-00020  

Standard Clearance:
Boot setting clamp Clearance
Inside 2.8 to 3.8 mm (0.110 to 0.150 in.)
Outside 3.0 to 4.0 mm (0.118 to 0.157 in.)



Hide 04438A 7.TEMPORARILY INSTALL FRONT DRIVE SHAFT INBOARD JOINT BOOT

a.

Wrap the spline of the outboard joint shaft with vinyl tape to prevent the boots from being damaged.


b.

Temporarily install the new inboard joint boot to the outboard joint shaft.


Hide 8.INSTALL FRONT DRIVE SHAFT INBOARD JOINT SHAFT ASSEMBLY

a.
C158357E01
2.661,1.255 3.299,1.595 0.638,0.340 10 Outboard Joint Side

Install the cage to the outboard joint shaft.

NOTICE:

Install the cage with its smaller inner diameter side facing the outboard joint.



b.
C158394E03
0.876,1.833 2.025,1.766 2.025,1.766 1.353,1.522 false 2.084,1.68 2.858,1.833 0.774,0.152 10 Matchmarks

Align the matchmarks and install the inner race onto the outboard joint shaft.


c.
C158392

Using a snap ring expander, install a new snap ring.


d.
C158395E08
2.542,1.271 1.958,0.146 1.958,0.146 2.438,1.354 false 1.958,0.146 2.396,1.5 false 1.198,0.031 1.99,0.188 0.792,0.156 10 false Matchmarks

Align the matchmarks placed before removal, and install the cage to the inner race.


e.
C115633

Install the 6 balls.

HINT:

Apply grease onto the balls to keep them from falling out.



f.

Pack the inboard joint shaft and boot with grease from the boot kit.

Standard grease capacity:

380 to 400 g (13.4 to 14.1 oz.)



g.
C115632E03
0.215,0.122 1.019,0.301 0.804,0.179 10 Matchmarks 1.888,0.649 1.183,0.225 1.183,0.225 1.521,1.027 false

Align the matchmarks placed before removal, and install the inboard joint shaft to the outboard joint shaft.


h.

Install a new snap ring.


Hide 04438A 9.INSTALL FRONT DRIVE SHAFT INBOARD JOINT BOOT

a.

Install the inboard joint boot into the groove on the outboard joint shaft and inboard joint shaft.

NOTICE:

Keep the groove where you are fitting the boot free of grease.



b.
C175125E03
1.375,1.594 1.781,1.844 0.406,0.25 10 false (A)

Check whether the drive shaft dimensions are within the following specifications.

Standard drive shaft length (A):

625.8 mm (24.64 in.)



Hide 43448B 10.INSTALL FRONT AXLE NO. 2 INBOARD JOINT BOOT SETTING CLAMP

a.

Install the No. 2 inboard joint boot setting clamp.

HINT:

Use the same procedure as for the outboard side.



Hide 43448A 11.INSTALL FRONT AXLE NO. 1 INBOARD JOINT BOOT SETTING CLAMP

a.

Install the inboard joint boot setting clamp.

HINT:

Use the same procedure as for the outboard side.



Hide 12.INSPECT AND ADJUST FRONT AXLE INBOARD JOINT BOOT SETTING CLAMP

a.

Inspect and adjust the clearance of the boot setting clamps.

HINT:

Use the same procedure as for the outboard side.



Hide 43411C 13.INSTALL FRONT DRIVE INNER SHAFT OUTER SHAFT SNAP RING

a.
C174231

Install a new snap ring onto the inboard joint shaft.


Hide 43420 14.INSPECT FRONT DRIVE SHAFT ASSEMBLY

a.
C175125E03
1.375,1.594 1.781,1.844 0.406,0.25 10 false (A)

Check whether the drive shaft dimensions are within the following specifications.

Standard drive shaft length (A):

625.8 mm (24.64 in.)



b.
C175123

Check for noticeable looseness when turning the joint up and down, left and right, and in the thrust direction.


c.

Check for cracks, damage and grease leakage on the boot joint.

NOTICE:

Keep the drive shaft level while moving it.