Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › REAR DRIVE SHAFT ASSEMBLY
RM27L0U _52 Drivetrain _049313 DRIVE SHAFT / PROPELLER SHAFT _0235682 REAR DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  REAR DRIVE SHAFT ASSEMBLY  DISASSEMBLY  


PROCEDURE

Hide 42360M 1.REMOVE REAR DRIVE SHAFT INBOARD JOINT SHAFT SNAP RING

a.
C057543

Using a screwdriver, remove the inboard joint shaft snap ring.

NOTICE:

Do not damage the spline of the inboard joint shaft.



Hide 42347D 2.REMOVE REAR DRIVE SHAFT INBOARD JOINT BOOT CLAMP

a.

Using a side cutter, cut the inboard joint boot clamp and remove it.


Hide 42347F 3.REMOVE REAR DRIVE SHAFT NO. 2 INBOARD JOINT BOOT CLAMP

a.

Using a side cutter, cut the No. 2 inboard joint boot clamp and remove it.


Hide 04437D 4.DISCONNECT REAR DRIVE SHAFT INBOARD JOINT BOOT

a.
C353596

Disconnect the inboard joint boot from the inboard joint shaft.


Hide 5.REMOVE REAR DRIVE SHAFT INBOARD JOINT SHAFT ASSEMBLY

a.
C115632E08
1.885,0.646 1.188,0.229 1.188,0.229 1.521,1.031 false 0.396,0.094 1.198,0.271 0.802,0.177 10 false Matchmarks

Place matchmarks on the inboard joint shaft and outboard joint shaft.

NOTICE:

Do not punch the marks.



b.

Using a screwdriver, remove the snap ring from the inboard joint shaft.


c.

Remove the inboard joint shaft from the outboard joint shaft.


d.
C115633E09
2.573,1.271 2.104,0.125 2.104,0.125 2.458,1.354 false 2.104,0.125 2.406,1.469 false 1.302,0.042 2.104,0.219 0.802,0.177 10 false Matchmarks

Place matchmarks on the outboard joint shaft, inner race and cage.

NOTICE:

Do not punch the marks.



e.

Remove the 6 balls.


f.

Slide the cage to the outboard joint side.


g.
C158392

Using a snap ring expander, remove the snap ring.


h.
C158393

Using a brass bar and hammer, tap out the inner race.

NOTICE:

Be careful not to damage the inner race.



i.

Remove the cage.


Hide 04437D 6.REMOVE REAR DRIVE SHAFT INBOARD JOINT BOOT

a.

Remove the inboard joint boot from the outboard joint shaft.


Hide 42346D 7.REMOVE REAR DRIVE SHAFT OUTBOARD JOINT BOOT CLAMP

a.

Using a side cutter, cut the outboard joint boot clamp and remove it.


Hide 42346F 8.REMOVE REAR DRIVE SHAFT NO. 2 OUTBOARD JOINT BOOT CLAMP

a.

Using a side cutter, cut the No. 2 outboard joint boot clamp and remove it.


Hide 04438Q 9.REMOVE REAR DRIVE SHAFT OUTBOARD JOINT BOOT

a.

Remove the outboard joint boot from the outboard joint shaft.


Hide 41336K 10.REMOVE REAR DRIVE SHAFT DUST COVER

a.
C124194E02
1.206,0.924 0.845,0.449 false 0.463,0.357 0.761,0.517 0.298,0.160 10 SST

Using SST and a press, press out the dust cover from the inboard joint shaft.

SST
09950-00020  

NOTICE:

Do not drop the inboard joint shaft.



Hide 11.REMOVE REAR DRIVE SHAFT DUST SEAL

a.
C124193E02
1.391,0.763 0.855,0.38 false 0.443,0.288 0.747,0.467 0.304,0.179 10 SST

Using SST and a press, press out the dust seal from the outboard joint shaft assembly.

SST
09950-00020  

NOTICE:

Do not drop the outboard joint shaft assembly.