Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER ASSEMBLY(for 4WD)
RM27L0U _52 Drivetrain _049314 AXLE AND DIFFERENTIAL _0235691 FRONT DIFFERENTIAL CARRIER ASSEMBLY(for 4WD) A

AXLE AND DIFFERENTIAL  FRONT DIFFERENTIAL CARRIER ASSEMBLY(for 4WD)  DISASSEMBLY  


PROCEDURE

Hide 41400 1.REMOVE AUTOMATIC DISCONNECTING DIFFERENTIAL ACTUATOR

a.
C159257

Remove the 4 bolts.


b.

Using a hammer handle, remove the actuator.


Hide 41320 2.REMOVE FRONT DIFFERENTIAL TUBE ASSEMBLY

a.
C159258

Remove the 4 bolts.


b.

Using a plastic-faced hammer, remove the differential tube.


Hide 41304P 3.REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL

a.
C159259E01
1.522,1.238 2.127,0.738 false 2.195,0.617 2.735,0.848 0.540,0.231 10 SST

Using SST, tap out the oil seal.

SST
09308-00010  


Hide 41306F 4.REMOVE DIFFERENTIAL SIDE GEAR INTER SHAFT SUB-ASSEMBLY

a.
U152224E01
1.771,1.438 2.802,1.604 2.802,1.604 1.885,1.198 true 2.865,1.531 3.313,1.75 0.448,0.219 10 false SST 2.813,0.188 3.031,0.375 0.219,0.188 10 true *a 0.229,1.104 0.448,1.292 0.219,0.188 10 false *b

Using SST, remove the side gear inter shaft.

SST
09350-20015  (09369-20040)
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04011, 09957-04010, 09958-04011)

Text in Illustration
*a Turn
*b Hold


b.

Remove the snap ring from the side gear inter shaft.


Hide 41204E 5.REMOVE FRONT DRIVE PINION COMPANION FLANGE FRONT NUT

a.
C159261E01
1.704,1.313 2.341,1.041 false 2.375,0.917 2.690,1.073 0.316,0.156 10 SST

Using SST and a hammer, unstake the nut.

SST
09930-00010  


b.
C159262E01
2.742,0.768 2.518,0.991 false 2.783,0.643 3.123,0.810 0.341,0.167 10 SST

Using SST to hold the companion, remove the nut.

SST
09330-00021  (09330-00030)


Hide 41204D 6.REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
C159263E05
1.469,0.635 1.031,0.49 false 0.698,0.385 1.208,0.615 0.51,0.229 10 false SST 2.635,0.74 2.833,0.917 0.198,0.177 10 false *a 0.521,1.479 0.719,1.656 0.198,0.177 10 false *b

Using SST, remove the companion flange from the differential carrier.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

Text in Illustration
*a Turn
*b Hold


Hide 41101D 7.REMOVE FRONT DIFFERENTIAL CARRIER OIL SEAL

a.
C159264E01
1.439,0.804 1.039,0.592 false 0.666,0.501 0.995,0.675 0.330,0.173 10 SST

Using SST, remove the oil seal.

SST
09308-10010  


Hide 41214C 8.REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41141L 9.REMOVE FRONT DIFFERENTIAL CROSS SHAFT BEARING RETAINER

a.
C160133E01
2.303,0.58 2.441,0.750 0.139,0.170 10 A 1.4,0.626 1.539,0.795 0.139,0.170 10 A 0.919,0.767 1.058,0.937 0.139,0.170 10 A 0.524,0.918 0.662,1.088 0.139,0.170 10 A 2.909,1.068 3.047,1.238 0.139,0.170 10 A 3.012,1.569 3.150,1.739 0.139,0.170 10 A 1.389,2.706 1.528,2.876 0.139,0.170 10 A 1.018,2.442 1.156,2.612 0.139,0.170 10 A 0.832,2.235 0.970,2.405 0.139,0.170 10 A 0.623,2.067 0.761,2.237 0.139,0.170 10 A 0.142,1.907 0.281,2.076 0.139,0.170 10 A 2.976,1.927 3.229,2.096 0.253,0.170 10 B 2.71,2.704 2.963,2.874 0.253,0.170 10 B 2.311,2.775 2.564,2.944 0.253,0.170 10 B

Remove the bolts B and front differential front support assembly LH.


b.

Remove the bolts A.


c.

Using a plastic-faced hammer, tap out the bearing retainer.


Hide 10.REMOVE DIFFERENTIAL CASE ASSEMBLY

a.

Remove the differential case from the differential carrier.


Hide 11.REMOVE DIFFERENTIAL DRIVE PINION

a.

Set the differential carrier to an overhaul stand as shown in the illustration.


b.
C159434E03
0.572,2.816 1.019,2.967 0.446,0.151 10 *a 0.77,2.383 0.665,2.794 false

Using a press, press out the drive pinion.

Text in Illustration
*a Block

NOTICE:

Do not drop the drive pinion.



Hide 41211B 12.REMOVE FRONT DRIVE PINION FRONT RADIAL BALL BEARING

a.

Remove the bearing (inner race) from the differential carrier.


Hide 41231F 13.REMOVE FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER

Hide 41183C 14.REMOVE FRONT DIFFERENTIAL BREATHER PLUG OIL DEFLECTOR

a.
C159446

Remove the 2 bolts and oil deflector.


Hide 41110V 15.REMOVE FRONT DIFFERENTIAL UNION

a.
C159447

Remove the front differential union from the differential carrier.


Hide 41211A 16.REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C294202E06
2.854,0.969 2.729,0.969 2.729,0.969 2.729,1.406 false 1.167,1.938 1.052,1.938 1.052,1.938 0.948,1.635 false 2.885,0.896 3.208,1.073 0.323,0.177 10 false SST 1.198,1.844 1.521,2.021 0.323,0.177 10 false SST

Using SST and a press, press out the bearing (inner race).

SST
09950-00020  

If the drive gear or ring gear is damaged, replace them as a set.


Hide 41211A 17.REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C159337

Using a brass bar and hammer, tap out the bearing (outer race) and washer.


Hide 41211B 18.REMOVE FRONT DRIVE PINION FRONT RADIAL BALL BEARING

a.
C159338E01
1.5,1.174 0.718,1.225 0.718,1.225 1.379,1.442 false 0.351,1.141 0.684,1.296 0.333,0.156 10 SST

Using SST and hammer, tap out the bearing (outer race).

SST
09950-70010  (09951-07100)
09950-60010  (09951-00450)
09950-60020  (09951-00710, 09952-06010)


Hide 41311A 19.REMOVE FRONT DIFFERENTIAL CASE BEARING

HINT:
·

Measure the plate washer and note its thickness.

·

Tag the bearing outer races to show the location for reassembly.



a.
C159266E03
1.483,0.836 0.92,0.685 0.92,0.685 1.384,1.129 false 0.561,0.586 0.984,0.748 0.423,0.162 10 SST 1.794,0.099 1.978,0.261 0.184,0.162 10 *1 2.411,0.741 2.001,0.197 false

Using SST and a press, press out the bearing (outer race) and plate washer from the bearing retainer.

SST
09950-60020  (09951-00680)
09950-70010  (09951-07150)

Text in Illustration
*1 Plate Washer


b.
C159267E03
1.327,0.788 0.8,0.53 0.8,0.53 1.223,0.991 false 0.426,0.414 0.766,0.566 0.340,0.152 10 SST 2.342,1.672 2.544,1.824 0.203,0.152 10 *1 2.433,0.857 2.217,1.75 2.217,1.75 2.285,1.75 false

Using SST and a press, press out the outer race and plate washer from the differential carrier.

SST
09950-60020  (09951-00680)
09950-70010  (09951-07150)

Text in Illustration
*1 Plate Washer


Hide 20.REMOVE DIFFERENTIAL RING GEAR

a.
U152222E01
2.01,1.406 2.167,1.74 2.167,1.74 2.208,1.74 false 2.26,1.688 2.458,1.854 0.198,0.167 10 false *a

Place matchmarks on the ring gear and differential case.

Text in Illustration
*a Matchmark


b.

Remove the 12 bolts.


c.

Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.


Hide 41311A 21.REMOVE FRONT DIFFERENTIAL CASE BEARING

a.
U152223E01
1.354,0.637 1.85,0.615 1.85,0.615 1.397,1.328 false 1.897,0.514 2.322,0.673 0.425,0.160 10 SST

Using SST, remove the 2 bearings (inner race).

SST
09950-60010  (09951-00550)
09950-40011  (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)

HINT:

Fix the claws of SST into the notch in the differential case assembly.



Hide 22.DISASSEMBLE DIFFERENTIAL CASE

a.
C159245

Using a pin punch and hammer, tap out the straight pin.


b.

Remove these parts from the differential case assembly.

i.

2 differential side gears


ii.

2 differential side gear thrust washers


iii.

Differential pinion shaft


iv.

2 differential pinion gears


v.

2 differential pinion gear thrust washers



Hide 41039A 23.INSPECT DIFFERENTIAL GEAR KIT

a.

Check that there is no damage to the pinion gear and side gear.

If the pinion gear and/or side gear is damaged, replace the differential gear kit.


Hide 41311 24.INSPECT FRONT DIFFERENTIAL CASE

a.

Check that the differential case is not damaged.

If the differential case is damaged, replace it.


Hide 41331G 25.REMOVE FRONT DIFFERENTIAL SIDE GEAR NEEDLE ROLLER BEARING

a.
C160136

Using a brass bar and hammer, tap out the 2 bearings.


Hide 41434 26.REMOVE DIFFERENTIAL CLUTCH HUB

a.
C159246

Using a snap ring expander, remove the snap ring.


b.

Remove the differential clutch hub.


Hide 41304P 27.REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL

a.
C353020E01
1.146,1.271 1.604,1.583 false 1.656,1.531 2.115,1.729 0.458,0.198 10 false SST

Using SST, tap out the oil seal.

SST
09308-00010  


Hide 41304F 28.REMOVE DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH

a.
C159248

Using a snap ring expander, remove the snap ring.


b.
C159247

Using a plastic-faced hammer, tap out the side gear shaft.


Hide 41311A 29.REMOVE FRONT DIFFERENTIAL SIDE GEAR SHAFT RH BEARING

a.
C159249

Using a snap ring expander, remove the snap ring.


b.
C159250E01
1.614,0.6 0.84,0.741 0.84,0.741 1.207,1.032 false 0.473,0.655 0.792,0.811 0.319,0.156 10 SST 0.84,0.741 1.524,0.829 false

Using SST, a brass bar and press, press out the bearing.

SST
09950-00020  
09950-70010  (09951-07100)
09950-60010  (09951-00450)

NOTICE:

Do not damage the bearing.



Hide 30.INSPECT DIFFERENTIAL CLUTCH SLEEVE AND DIFFERENTIAL CLUTCH HUB

a.
G023141

Check for wear and damage to the clutch hub and clutch sleeve.

If necessary, replace them.


b.

Check that the clutch sleeve slides smoothly on the clutch hub.


Hide 31.INSPECT DIFFERENTIAL CLUTCH SLEEVE AND DIFFERENTIAL SIDE GEAR INTER SHAFT

a.
G023144

Check for wear and damage to the clutch hub and side gear inter shaft.


b.

Check that the clutch sleeve slides smoothly on the side gear inter shaft.


Hide 41433 32.INSPECT DIFFERENTIAL CLUTCH SLEEVE AND CLUTCH SLEEVE FORK CLEARANCE

a.
C159251

Using a feeler gauge, measure the clearance between the sleeve fork and clutch sleeve.

Maximum clearance:

0.35 mm (0.0138 in.)


If the clearance exceeds the maximum, replace the fork or clutch sleeve.