Home › Drivetrain › AXLE AND DIFFERENTIAL › AUTOMATIC DISCONNECTING DIFFERENTIAL ACTUATOR(for 4WD)
RM27L0U _52 Drivetrain _049314 AXLE AND DIFFERENTIAL _0235692 AUTOMATIC DISCONNECTING DIFFERENTIAL ACTUATOR(for 4WD) G

AXLE AND DIFFERENTIAL  AUTOMATIC DISCONNECTING DIFFERENTIAL ACTUATOR(for 4WD)  INSPECTION  


PROCEDURE

Hide 41400 1.REMOVE AUTOMATIC DISCONNECTING DIFFERENTIAL ACTUATOR

a.
C237690E03
1.021,0.875 0.49,0.875 false 1.25,0.896 1.25,1.281 1.25,1.281 1.5,1.281 false 1.5,0.729 1.5,0.208 1.5,0.208 1.219,0.208 false 1.781,0.719 1.781,0.198 1.781,0.198 2.115,0.198 false 2.313,2.958 2.938,2.958 false 2.521,3.146 2.792,3.146 2.792,3.146 2.792,2.958 false 2.063,3.469 1.271,3.469 false 2.458,3.521 2.896,3.521 false 0.219,0.792 0.521,0.958 0.302,0.167 10 false DL1 1.542,1.188 1.844,1.354 0.302,0.167 10 false DL2 0.885,0.125 1.24,0.292 0.354,0.167 10 false GND 2.177,0.104 2.531,0.271 0.354,0.167 10 false ADD 2.99,2.885 3.177,3.052 0.188,0.167 10 false *1 1.052,3.375 1.24,3.542 0.188,0.167 10 false *a 2.927,3.417 3.115,3.583 0.188,0.167 10 false *b 2.167,4.156 2.354,4.323 0.188,0.167 10 false *c

Measure the resistance between terminals 1 and 2.

Standard:

0.1 to 100 Ω



b.

Measure the resistance between terminal 1 or 2 and body ground.

Standard:

5 MΩ or more


If the result is not as specified, replace the differential motor actuator.


c.

Check the actuator using one of the following methods.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Measurement Condition Specified Condition
3 (ADD) - 4(GND) Battery positive (+) → Terminal 1 Battery negative (-) → Terminal 2 Below 1 Ω
Battery positive (+) → Terminal 2 Battery negative (-) → Terminal 1 10 kΩ or higher
4 (GND) - 5 (DL2) Battery positive (+) → Terminal 1 Battery negative (-) → Terminal 2 Below 1 Ω
Battery positive (+) → Terminal 2 Battery negative (-) → Terminal 1 10 kΩ or higher
4 (GND) - 6 (DL1) Battery positive (+) → Terminal 1 Battery negative (-) → Terminal 2 Below 1 Ω
Battery positive (+) → Terminal 2 Battery negative (-) → Terminal 1 10 kΩ or higher


Text in Illustration
*1 Shift Fork
*a 2WD Side
*b 4WD Side
*c 12 mm (0.472 in.)

If the result is not as specified, replace the differential motor actuator assembly.


ii.

Check the actuator status.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 2
2WD → 4WD
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1
4WD → 2WD


If the result is not as specified, replace the differential motor actuator assembly.