Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY
RM27L0U _52 Drivetrain _049314 AXLE AND DIFFERENTIAL _0235701 REAR DIFFERENTIAL CARRIER ASSEMBLY A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY  DISASSEMBLY  


PROCEDURE

Hide 41204 1.INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
C181030E03
1.667,1.823 2.719,2.021 1.052,0.198 10 true 72 mm (2.83 in.)

Using a dial indicator, measure the runout of the companion flange vertically and laterally.

Maximum Runout:
Runout Specified Condition
Vertical runout 0.1 mm (0.00394 in.)
Lateral runout 0.1 mm (0.00394 in.)


If the runout is greater than the maximum, replace the companion flange.


Hide 41334B 2.REMOVE REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL

a.
C181010E02
0.844,1.198 0.906,1.344 false 0.802,1.375 1.104,1.573 0.302,0.198 10 false SST

Using SST, tap out the 2 differential side gear shaft oil seals.

SST
09308-00010  


Hide 41204B 3.REMOVE REAR DRIVE PINION NUT

a.
C181003E03
1.667,1.073 1.5,1.458 false 1.354,1.458 1.656,1.615 0.302,0.156 10 false SST

Using SST and a hammer, unstake the rear drive nut.

SST
09930-00010  


b.
C181026E02
1.948,2.479 1.615,3.125 false 1.396,3.156 1.698,3.313 0.302,0.156 10 false SST

Using SST to hold the rear drive pinion companion flange sub-assembly.

SST
09330-00021  


c.

Using a socket wrench (30mm), remove the rear drive pinion nut.

NOTICE:

Install nuts on the bolts to protect them, as shown in the illustration.



Hide 41204 4.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
C181017E01
2.164,1.081 2.463,1.233 0.298,0.152 10 SST 2.164,1.162 1.743,1.55 false

Using SST, remove the rear drive pinion companion flange sub-assembly from the rear differential carrier assembly.

HINT:

Use the propeller shaft installation nuts when mounting SST on the flange.


SST
09950-30012  (09951-03010, 09953-03010, 09954-03010)
09955-03050  


Hide 41201C 5.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

a.
C181008E01
1.204,1.144 1.517,1.299 0.313,0.155 10 SST 1.251,1.007 1.355,1.144 false

Using SST, remove the rear differential carrier oil seal.

SST
09308-10010  


Hide 41214 6.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

a.
C181009

Remove the rear differential drive pinion oil slinger from the rear differential carrier assembly.


Hide 41201B 7.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C180990E01
2.97,0.573 3.311,0.787 0.341,0.213 10 SST 2.398,0.923 2.953,0.665 2.953,0.665 2.351,0.801 false 2.657,1.127 2.953,0.665 false

Remove the bearing (inner race) from the differential carrier.

SST
09950-40011  (09951-04010, 09953-04020, 09952-04010, 09954-04010)
09955-04110  
09958-04020  


Hide 41141B 8.REMOVE REAR DIFFERENTIAL SIDE BEARING RETAINER

a.
C180991

Remove the 12 bolts and 2 straight pin.


b.

Using a plastic-faced hammer, tap out the rear differential side bearing retainer.


Hide 41301 9.REMOVE REAR DIFFERENTIAL CASE SUB-ASSEMBLY

a.
C180993

Remove the differential case from the differential carrier.


Hide 10.REMOVE DIFFERENTIAL DRIVE PINION

a.

Remove the differential case from the differential drive pinion.


Hide 41183 11.REMOVE REAR DIFFERENTIAL BREATHER PLUG OIL DEFLECTOR

a.
C180994

Remove the 2 bolts and rear differential breather plug oil deflector.


Hide 41108C 12.REMOVE REAR DIFFERENTIAL CARRIER COVER BREATHER PLUG

a.
C181031

Remove the rear differential carrier cover breather plug from the rear differential carrier.


Hide 41201A 13.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C116049E02
0.542,0.198 0.813,0.198 false 0.813,0.198 0.813,1.01 false 0.25,0.115 0.583,0.271 0.333,0.156 10 false SST

Using SST and a press, press out the bearing (inner race).

SST
09950-00020  

If the drive gear or ring gear is damaged, replace them as a set.


Hide 41201B 14.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C159337

Using a brass bar and hammer, tap out the bearing (outer race) and washer.


Hide 41201A 15.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C181151E01
1.5,0.732 0.614,0.611 0.614,0.611 1.39,0.996 false 0.258,0.563 0.554,0.754 0.297,0.191 10 SST

Using SST and hammer, tap out the bearing (outer race).

SST
09950-70010  (09951-07100)
09950-60020  (09952-06010, 09951-00680, 09951-00730)


Hide 41301A 16.REMOVE REAR DIFFERENTIAL CASE BEARING

HINT:
·

Measure the plate washer and note its thickness.

·

Tag the bearing outer races to show the location for reassembly.



a.
C180996E01
0.645,1.004 0.958,1.160 0.313,0.156 10 SST 1.527,1.359 1.011,1.096 1.011,1.096 1.658,1.216 false

Using SST and a press, press out the bearing (outer race) and plate washer from the bearing retainer.

SST
09950-60020  (09951-00790)
09950-70010  (09951-07150)


b.
C180998E01
0.676,0.855 0.973,1.008 0.297,0.153 10 SST 1.254,1.235 1.023,0.944 1.023,0.944 1.34,1.087 false

Using SST and a press, press out the outer race and plate washer from the differential carrier.

SST
09950-60020  (09951-00790)
09950-70010  (09951-07150)


Hide 41311A 17.REMOVE FRONT DIFFERENTIAL CASE BEARING

a.
C181000E02
1.156,1.688 0.438,2.344 0.438,2.344 1.625,2.323 true 1.323,2.177 0.438,2.344 false 0.063,2.292 0.385,2.479 0.323,0.188 10 false SST

Using SST, remove the 2 bearings (inner race).

SST
09950-60010  (09951-00390, 09951-00560, 09952-06010)
09950-40011  (09951-04010, 09953-04020, 09952-04010, 09954-04010, 09957-04010, 09958-04011)
09955-04120  

HINT:

Fix the claws of SST into the notch in the differential case assembly.



Hide 18.REMOVE DIFFERENTIAL RING GEAR

a.
C181001E01
2.322,1.302 3.120,1.468 0.798,0.166 10 Matchmarks 2.039,1.219 2.322,1.399 false

Place matchmarks on the ring gear and differential case.


b.

Remove the 12 bolts.


c.

Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.