Home › Suspension › SUSPENSION CONTROL › HEIGHT CONTROL SENSOR
RM27L0U _53 Suspension _049315 SUSPENSION CONTROL _0235706 HEIGHT CONTROL SENSOR G

SUSPENSION CONTROL  HEIGHT CONTROL SENSOR  INSPECTION  


PROCEDURE

Hide 89408D 1.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY

C179494E02
0.096,2.387 2.529,2.788 2.434,0.401 10 Component without harness connector: (Rear Height Control Sensor LH) 0.622,1.525 0.907,1.701 0.285,0.176 10 Low 2.726,1.932 3.107,2.108 0.382,0.176 10 High 1.429,2.134 1.909,2.310 0.480,0.176 10 Normal 0.753,3.414 1.274,3.590 0.520,0.176 10 3 (SHB) 2.278,4.246 2.838,4.422 0.560,0.176 10 1 (SHG) 2.272,3.179 2.907,3.355 0.635,0.176 10 2 (SHRL) 1.324,1.63 1.659,1.805 0.334,0.176 10 45° 2.142,1.773 2.476,1.949 0.334,0.176 10 45° 2.212,3.257 1.752,3.758 false 1.929,3.845 2.202,4.329 false 1.608,3.794 1.396,3.488 false

a.

Inspect the rear height control sensor sub-assembly LH.


b.

Connect 3 dry cell batteries of 1.5 V in series.


c.

Connect the positive (+) end of the batteries to terminal 3 (SHB) of the height control sensor and the negative (-) end of the batteries to terminal 1 (SHG). While slowly moving the sensor link up and down, measure the voltage between terminal 2 (SHRL) and terminal 1 (SHG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Sensor Condition Specified Condition
2 (SHRL) - 1 (SHG) High (45°) 3.60 to 4.52 V
Normal (0°) 2.06 to 2.45 V
Low (-45°) 0.40 to 0.51 V


NOTICE:

Do not apply a voltage of more than 6 V.



e.
C179494E01
0.622,1.525 0.907,1.701 0.285,0.176 10 Low 2.726,1.932 3.107,2.108 0.382,0.176 10 High 0.096,2.387 2.529,2.788 2.434,0.401 10 Component without harness connector: (Rear Height Control Sensor RH) 1.429,2.134 1.909,2.310 0.480,0.176 10 Normal 0.753,3.414 1.274,3.590 0.520,0.176 10 3 (SHB) 2.278,4.246 2.838,4.422 0.560,0.176 10 1 (SHG) 2.272,3.179 2.907,3.355 0.635,0.176 10 2 (SHRR) 1.324,1.63 1.659,1.805 0.334,0.176 10 45° 2.142,1.773 2.476,1.949 0.334,0.176 10 45° 2.212,3.257 1.752,3.758 false 1.929,3.845 2.202,4.329 false 1.608,3.794 1.396,3.488 false

Inspect the rear height control sensor sub-assembly RH.


f.

Connect 3 dry cell batteries of 1.5 V in series.


g.

Connect the positive (+) end of the batteries to terminal 3 (SHB) of the height control sensor and the negative (-) end of the batteries to terminal 1 (SHG). While slowly moving the sensor link up and down, measure the voltage between terminal 2 (SHRR) and terminal 1 (SHG).


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Sensor Condition Specified Condition
2 (SHRR) - 1 (SHG) High (45°) 3.60 to 4.52 V
Normal (0°) 2.06 to 2.45 V
Low (-45°) 0.40 to 0.51 V


NOTICE:

Do not apply a voltage of more than 6 V.