CHECK SUSPENSION CONTROL ECU
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| O16-1 (IG) - O16-5 (GND) | R - W-B | IG power supply | Ignition switch ON | 10 to 14 V |
| O16-3 (B) - O18-10 (GND) | SB - W-B | +B power supply | Ignition switch ON | 10 to 14 V |
| O16-5 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1.0 Ω |
| O16-7 (CANH) - O18-10 (GND) | B - W-B | CAN communication line | Ignition switch ON | Pulse generation
(See waveform 2) |
| O16-8 (CANL) - O18-10 (GND) | W - W-B | CAN communication line | Ignition switch ON | Pulse generation
(See waveform 1) |
| O16-13 (TD) - O16-5 (GND) | L - W-B | Height control mode select switch | Ignition switch ON, Height control select switch ON | Below 1.5 V |
| Ignition switch ON, Height control select switch OFF | 10 to 14 V | |||
| O16-14 (DNSW) - O16-5 (GND) | GR - W-B | Height control switch (DOWN) | Ignition switch ON, "DOWN" button of height control switch pushed in | Below 1.5 V |
| Ignition switch ON, "DOWN" button of height control switch released | 10 to 14 V | |||
| O16-15 (UPSW) - O16-5 (GND) | Y - W-B | Height control switch (UP) | Ignition switch ON, "UP" button of height control switch pushed in | Below 1.5 V |
| Ignition switch ON, "UP" button of height control switch released | 10 to 14 V | |||
| O16-16 (SGR3) - O16-5 (GND) | B - W-B | Front acceleration sensor LH ground | Always | Below 1.0 Ω |
| O16-17 (SBR3) - O16-16 (SGR3) | P - B | Front acceleration sensor LH power source | Ignition switch ON | 4.5 to 5.5 V |
| O16-22 (TSW2) - O16-5 (GND) | V - W-B | Absorber control switch (SPORT) | Ignition switch ON, Absorber control switch select "NORMAL" | 10 to 14 V |
| Ignition switch ON, Absorber control switch select "SPORT" | Below 1.5 V | |||
| O16-23 (TSW1) - O16-5 (GND) | R - W-B | Absorber control switch (COMFORT) | Ignition switch ON, Absorber control switch select "NORMAL" | 10 to 14 V |
| Ignition switch ON, Absorber control switch select "COMFORT" | Below 1.5 V | |||
| O16-26 (SGRR) - O16-16 (SGR3) | BE - B | Front acceleration sensor LH | Always | 0.5 to 4.5 V |
| O17-9 (SBR) - O17-10 (SGR) | G - V | Front acceleration sensor RH power source | Ignition switch ON | 4.5 to 5.5 V |
| O17-10 (SGR) - Body ground | V - Body ground | Front acceleration sensor RH ground | Always | Below 1.0 Ω |
| O17-15 (SLRL) - O16-5 (GND) | BE - W-B | Height control valve (Gate solenoid valve) | Ignition switch ON | Below 1.0 V |
| Engine idling, button of height control switch is pushed from "DOWN" to "UP" | 9 V or more | |||
| O17-16 (SLRR) - O16-5 (GND) | B - W-B | Height control valve (Leveling solenoid valve) | Ignition switch ON | Below 1.0 V |
| Engine idling, button of height control switch is pushed from "DOWN" to "UP" | 9 V or more | |||
| O17-17 (RM-) - O16-5 (GND) | P - W-B | Motor lock (-) | Always | Below 1.0 Ω |
| O17-18 (SGFR) - O17-10 (SGR) | Y - V | Front acceleration sensor RH | Always | 0.5 to 4.5 V |
| O17-19 (RM+) - O16-5 (GND) | G - W-B | Motor lock (+) | Engine idling, vehicle height changes from "NORMAL" to "HIGH" by pressing the height control switch (While height control compressor assembly is working). | Below 1.0 Ω |
| O18-9 (SLEX) - O16-5 (GND) | V - W-B | Exhaust valve | Ignition switch ON | Below 1.0 V |
| Engine idling, button of height control switch is pushed from "UP" to "DOWN" | 9 V or more | |||
| O18-10 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1.0 Ω |
| O18-13 (SBR2) - O18-16 (SGR2) | L - BR | Height control sensor RH power source | Ignition switch ON | 4.5 to 5.5 V |
| O18-14 (SBL2) - O18-15 (SGL2) | LG - V | Height control sensor LH power source | Ignition switch ON | 4.5 to 5.5 V |
| O18-15 (SGL2) - O16-5 (GND) | V - W-B | Height control sensor LH ground | Always | Below 1.0 Ω |
| O18-16 (SGR2) - O16-5 (GND) | BR - W-B | Rear height control sensor RH ground | Always | Below 1.0 Ω |
| O18-22 (RC) - O16-5 (GND) | LG - W-B | Suspension control relay | Ignition switch ON | Below 1.0 V |
| Engine idling, button of height control switch is pushed from "DOWN" to "UP" | 9 V or more | |||
| O18-24 (SHRL) - O18-15 (SGL2) | Y - V | Height control sensor LH | Ignition switch ON | 0.5 to 4.5 V |
| Engine idling, vehicle height is changed from "HIGH" to "NORMAL" by pressing the height control switch | 2.4 to 2.7 V | |||
| O18-26 (SHRR) - O18-16 (SGR2) | R - BR | Height control sensor RH | Ignition switch ON | 0.5 to 4.5 V |
| Engine idling, vehicle height is changed from "HIGH" to "NORMAL" by pressing the height control switch | 2.4 to 2.7 V |
If the result is not as specified, the ECU may have a malfunction.
Using an oscilloscope, check the waveform 1.
| Terminal No. (Symbol) | O16-8 (CANL) - O18-10 (GND) |
| Tool Setting | 1 V/DIV, 10 μs/DIV |
| Vehicle Condition | Ignition switch ON, Engine stopped |
Using an oscilloscope, check the waveform 2.
| Terminal No. (Symbol) | O16-7 (CANH) - O18-10 (GND) |
| Tool Setting | 1 V/DIV, 10 μs/DIV |
| Vehicle Condition | Ignition switch ON, Engine stopped |