Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM
RM27L0U _53 Suspension _049315 SUSPENSION CONTROL _0235712 AIR SUSPENSION SYSTEM C

SUSPENSION CONTROL  AIR SUSPENSION SYSTEM  C1715  Front Acceleration Sensor RH Malfunction  C1716  Front Acceleration Sensor LH Malfunction  C1717  Rear Acceleration Sensor Malfunction  C1796  Front Acceleration Sensor RH Malfunction (Test Mode DTC)  C1797  Front Acceleration Sensor LH Malfunction (Test Mode DTC)  C1798  Rear Acceleration Sensor Malfunction (Test Mode DTC)  


DESCRIPTION

The acceleration sensor (up and down G sensor) detects the upward and downward acceleration of the vehicle, and outputs it as a voltage to the suspension control ECU. Up and down G sensors are installed in 3 locations: 1) the suspension control ECU, 2) the driver side instrument panel, and 3) the passenger side instrument panel. Each up and down G sensor independently detects the upward and downward acceleration. During a test mode inspection, the suspension control ECU reads the fluctuations in each sensor's signal. If a sensor's signal does not fluctuate, test mode DTCs C1796, C1797 and C1798 are output.

DTC Code Detection Condition Trouble Area
C1715 With the ignition switch ON, a voltage of 4.7 V or more, or 0.3 V or less at front acceleration sensor RH is detected for 1 second.
·

Wire harness or connector

·

Front acceleration sensor RH

·

Suspension control ECU


C1716 With the ignition switch ON, a voltage of 4.7 V or more, or 0.3 V or less at front acceleration sensor LH is detected for 1 second.
·

Wire harness or connector

·

Front acceleration sensor LH

·

Suspension control ECU


C1717 With the ignition switch ON, a voltage of 4.7 V or more, or 0.3 V or less at rear acceleration sensor is detected for 1 second.
·

Suspension control ECU


C1796 On level surface, G sensor input is +/- 1.96 m/s2 or more for 1 second or more.
·

Wire harness or connector

·

Front acceleration sensor RH

·

Suspension control ECU


C1797 On level surface, G sensor input is +/- 1.96 m/s2 or more for 1 second or more.
·

Wire harness or connector

·

Front acceleration sensor LH

·

Suspension control ECU


C1798 On level surface, G sensor input is +/- 1.96 m/s2 or more for 1 second or more.
·

Suspension control ECU



HINT:

If DTCs C1717 and C1798 (Rear Acceleration Sensor Malfunction) are output, replace the suspension control ECU (houses rear acceleration sensor).


WIRING DIAGRAM

C179515E15
0.24,2.323 0.563,2.51 0.323,0.188 10 false H75 0.24,2.521 2.26,2.896 2.021,0.375 10 false Front Acceleration Sensor LH 1.542,1.729 1.698,1.938 0.156,0.208 10 false 1 0.281,5.063 2.302,5.438 2.021,0.375 10 false H74 0.271,5.24 2.292,5.615 2.021,0.375 10 false Front Acceleration Sensor RH 5.344,5.094 7.01,5.469 1.667,0.375 10 false Suspension Control ECU 1.542,1.135 1.698,1.344 0.156,0.208 10 false 2 1.542,0.542 1.698,0.75 0.156,0.208 10 false 3 5.604,0.438 5.813,0.615 0.208,0.177 10 false 17 5.604,1.031 5.802,1.198 0.198,0.167 10 false 16 5.896,0.635 6.323,0.844 0.427,0.208 10 false SBR3 5.896,1.229 6.323,1.438 0.427,0.208 10 false SGR3 5.896,1.823 6.323,2.031 0.427,0.208 10 false SGRR 1.125,0.625 1.479,0.833 0.354,0.208 10 false SGV 1.042,1.229 1.469,1.438 0.427,0.208 10 false SGND 1.021,1.792 1.448,2 0.427,0.208 10 false SGRR 5.896,3.354 6.323,3.563 0.427,0.208 10 false SBR 5.896,3.948 6.323,4.156 0.427,0.208 10 false SGR 5.896,4.542 6.323,4.75 0.427,0.208 10 false SGFR 5.604,1.635 5.813,1.813 0.208,0.177 10 false 26 5.646,3.167 5.792,3.333 0.146,0.167 10 false 9 5.604,3.781 5.823,3.958 0.219,0.177 10 false 10 5.604,4.354 5.823,4.521 0.219,0.167 10 false 18 5.531,0.635 5.823,0.802 0.292,0.167 10 false O16 1.552,4.448 1.708,4.656 0.156,0.208 10 false 1 1.552,3.865 1.708,4.073 0.156,0.208 10 false 2 1.552,3.271 1.708,3.479 0.156,0.208 10 false 3 1.135,3.354 1.49,3.563 0.354,0.208 10 false SHB 1.115,3.948 1.458,4.156 0.344,0.208 10 false SHG 1.073,4.552 1.5,4.76 0.427,0.208 10 false SGFL 5.542,1.229 5.844,1.438 0.302,0.208 10 false O16 5.531,1.823 5.833,2.031 0.302,0.208 10 false O16 5.542,3.365 5.844,3.573 0.302,0.208 10 false O17 5.531,3.958 5.833,4.167 0.302,0.208 10 false O17 5.542,4.552 5.844,4.76 0.302,0.208 10 false O17

CAUTION / NOTICE / HINT

NOTICE:

After replacing the suspension control ECU, perform registration (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>REGISTRATION).


PROCEDURE

1.READ VALUE USING TECHSTREAM (G SENSOR)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON, and turn the Techstream main switch on.


c.

Enter the following menus: Chassis / Air suspension / Data List.

Air Suspension
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
(Up & Down) G Sensor FR G (up & down) front acceleration sensor RH reading /
min.: -1045.29 m/s2
max.: 1045.26 m/s2
0 +/- 0.98 m/s2 at still condition Reading changes when vehicle (FR) is bounced
(Up & Down) G Sensor FL G (up & down) front acceleration sensor LH reading /
min.: -1045.29 m/s2
max.: 1045.26 m/s2
0 +/- 0.98 m/s2 at still condition Reading changes when vehicle (FL) is bounced
(Up & Down) G Sensor Rear G (up & down) rear acceleration sensor reading /
min.: -1045.29 m/s2
max.: 1045.26 m/s2
0 +/- 0.98 m/s2 at still condition Reading changes when vehicle (rear) is bounced

OK:

Acceleration value changes.




OK

NG

2.INSPECT ACCELERATION SENSOR (FRONT LH OR RH)
2.INSPECT ACCELERATION SENSOR (FRONT LH OR RH)
a.

Turn the ignition switch off.


b.
C179517E03
1.802,1.646 1.573,2.083 true 2.219,1.635 2.49,2.083 true 2.042,1.563 2.448,1.042 true 1.896,2.854 2.427,3.052 0.531,0.198 10 false Upside 1.281,4.229 2.042,4.417 0.76,0.188 10 false Downside 1.229,2.052 1.604,2.25 0.375,0.198 10 false SHB 2.521,2.073 2.979,2.271 0.458,0.198 10 false SGFL 2.469,0.896 2.896,1.073 0.427,0.177 10 false SHG 0.052,0.042 2.646,0.771 2.594,0.729 10 false Component without harness connected: (Front Acceleration Sensor RH)

Check the acceleration sensor RH: (C1715, C1796).

i.

Remove the acceleration sensor RH (See page Suspension>SUSPENSION CONTROL>FRONT ACCELERATION SENSOR>REMOVAL).


ii.

Connect 3 dry cell batteries of 1.5 V in series.


iii.

Connect the positive (+) end of the batteries to terminal 3 (SHB) of the acceleration sensor and the negative (-) end of the batteries to terminal 2 (SHG). Then measure the voltage between terminal 1 (SGFL) and terminal 2 (SHG).


iv.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Sensor Condition Specified Condition
1 (SGFL) - 2 (SHG) Sensor stationary Approx. 2.0 to 2.5 V
Sensor is tilted Changes between approx. 0.9 to 2.3 V




c.
C179517E04
1.792,1.635 1.563,2.073 true 2.219,1.646 2.49,2.094 true 2.042,1.573 2.448,1.052 true 1.927,2.729 2.458,2.927 0.531,0.198 10 false Upside 1.281,4.229 2.042,4.417 0.76,0.188 10 false Downside 2.469,0.906 2.99,1.104 0.521,0.198 10 false SGND 2.531,2.083 2.99,2.281 0.458,0.198 10 false SGRR 1.26,2.063 1.688,2.24 0.427,0.177 10 false SGV 0.052,0.021 2.594,0.792 2.542,0.771 10 false Component without harness connected: (Front Acceleration Sensor LH)

Check the acceleration sensor LH: (C1716, C1797).

i.

Remove the acceleration sensor LH (See page Suspension>SUSPENSION CONTROL>FRONT ACCELERATION SENSOR>REMOVAL).


ii.

Connect 3 dry cell batteries of 1.5 V in series.


iii.

Connect the positive (+) end of the batteries to terminal 3 (SGV) of the acceleration sensor and the negative (-) end of the batteries to terminal 2 (SGND). Then measure the voltage between terminal 1 (SGRR) and terminal 2 (SGND).


iv.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Sensor Condition Specified Condition
1 (SGRR) - 2 (SGND) Sensor stationary Approx. 2.0 to 2.5 V
Sensor is tilted Changes between approx. 0.9 to 2.3 V


NOTICE:

Do not apply a voltage of more than 6 V.


HINT:

When the acceleration sensor is tilted, it may output a different value.


Result
Result Proceed to
OK A
NG (Front acceleration sensor RH) B
NG (Front acceleration sensor LH) C




A

3.CHECK HARNESS AND CONNECTOR (FRONT ACCELERATION SENSOR - ECU AND BODY GROUND)

B

REPLACE FRONT ACCELERATION SENSOR RH

C

REPLACE FRONT ACCELERATION SENSOR LH

3.CHECK HARNESS AND CONNECTOR (FRONT ACCELERATION SENSOR - ECU AND BODY GROUND)
a.
U153726E02
1.833,1.323 1.833,1.688 true 1.646,1.25 1.229,1.635 true 2.021,1.302 2.469,1.677 true 2.281,4.115 1.917,4.042 true 2.177,4.417 1.979,4.115 true 1.281,4.104 1.833,4.031 true 0.073,2 2.333,2.667 2.26,0.667 10 false Rear view of wire harness connector: (to Suspension Control ECU) 0.073,0.031 2.396,0.792 2.323,0.76 10 false Front view of wire harness connector: (to Front Acceleration Sensor RH) 1.625,2.781 1.927,2.948 0.302,0.167 10 false O17 2.333,4.063 2.917,4.26 0.583,0.198 10 false 9 (SBR) 0.677,4.031 1.323,4.219 0.646,0.188 10 false 10 (SGR) 2.208,4.406 2.958,4.594 0.75,0.188 10 false 18 (SGFR) 0.906,1.188 1.208,1.354 0.302,0.167 10 false H74 0.917,1.656 1.313,1.823 0.396,0.167 10 false SGFL 1.667,1.719 2.042,1.896 0.375,0.177 10 false SHG 2.417,1.688 2.76,1.854 0.344,0.167 10 false SHB

Check the acceleration sensor RH: (C1715, C1796).

i.

Disconnect the O17 ECU connector.


ii.

Disconnect the H74 sensor connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H74-1 (SGFL) - O17-18 (SGFR) Always Below 1 Ω
H74-2 (SHG) - O17-10 (SGR) Always Below 1 Ω
H74-3 (SHB) - O17-9 (SBR) Always Below 1 Ω
H74-1 (SGFL) or O17-18 (SGFR) - Body ground Always 10 kΩ or higher
H74-2 (SHG) or O17-10 (SGR) - Body ground Always 10 kΩ or higher
H74-3 (SHB) or O17-9 (SBR) - Body ground Always 10 kΩ or higher




b.
U153727E02
1.615,1.26 1.021,1.667 true 1.813,1.313 1.823,1.677 true 2.052,1.26 2.615,1.688 true 1.51,4.146 1.813,4.083 true 1.531,4.427 1.823,4.146 true 2.49,4.281 1.885,4.094 true 0.063,2.031 2.302,2.802 2.24,0.771 10 false Rear view of wire harness connector: (to Suspension Control ECU) 0.073,0.01 2.396,0.698 2.323,0.688 10 false Front view of wire harness connector: (to Front Acceleration Sensor LH) 1.958,2.958 2.25,3.125 0.292,0.167 10 false O16 0.844,4.063 1.542,4.271 0.698,0.208 10 false 17 (SBR3) 2.531,4.229 3.271,4.417 0.74,0.188 10 false 16 (SGR3) 0.854,4.385 1.604,4.573 0.75,0.188 10 false 26 (SGRR) 0.906,1.167 1.208,1.333 0.302,0.167 10 false H75 0.583,1.708 1.031,1.906 0.448,0.198 10 false SGRR 1.646,1.729 2.115,1.927 0.469,0.198 10 false SGND 2.552,1.708 3.083,1.938 0.531,0.229 10 false SGV

Check the acceleration sensor LH: (C1716, C1797).

i.

Disconnect the O16 ECU connector.


ii.

Disconnect the H75 sensor connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H75-1 (SGRR) - O16-26 (SGRR) Always Below 1 Ω
H75-2 (SGND) - O16-16 (SGR3) Always Below 1 Ω
H75-3 (SGV) - O16-17 (SBR3) Always Below 1 Ω
H75-1 (SGRR) or O16-26 (SGRR) - Body ground Always 10 kΩ or higher
H75-2 (SGND) or O16-16 (SGR3) - Body ground Always 10 kΩ or higher
H75-3 (SGV) or O16-17 (SBR3) - Body ground Always 10 kΩ or higher





OK

REPLACE SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR