Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM
RM27L0U _53 Suspension _049315 SUSPENSION CONTROL _0235712 AIR SUSPENSION SYSTEM C

SUSPENSION CONTROL  AIR SUSPENSION SYSTEM  C1762  Continuous Electric Current to Exhaust Solenoid  


DESCRIPTION

DTC Code Detection Condition Trouble Area
C1762 With the exhaust valve activated, the vehicle does not go down to the standard vehicle height after 105 seconds have elapsed.
·

Clogging in the air tube or each valve

·

Wire harness or connector

·

Leveling solenoid valve (No. 2 height control valve)

·

Gate solenoid valve (No. 2 height control valve)

·

Exhaust solenoid valve (No. 1 height control compressor)

·

Suspension control ECU



WIRING DIAGRAM

C179528E03
1.48,2.007 1.794,2.191 0.313,0.184 10 Q3 1.521,1.783 1.676,1.967 0.154,0.184 10 2 1.521,1.265 1.676,1.449 0.154,0.184 10 1 1.48,1.489 1.794,1.673 0.313,0.184 10 Q3 5.422,1.488 5.735,1.672 0.313,0.184 10 O18 5.851,1.494 6.230,1.677 0.378,0.184 10 SLEX 5.31,0.859 6.910,1.042 1.601,0.184 10 Suspension Control ECU 0.103,0.563 2.214,0.895 2.111,0.332 10 No. 1 Height Control Compressor (Exhaust Solenoid Valve) 5.517,1.273 5.671,1.457 0.154,0.184 10 9

CAUTION / NOTICE / HINT

NOTICE:

After replacing the suspension control ECU, perform registration (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>REGISTRATION).


PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (REAR GATE SOLENOID)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON, and turn the Techstream main switch on.


c.

Enter the following menus: Chassis / Air suspension / Active Test.

Air Suspension
Tester Display Test Part Control Range Diagnostic Note
Rear Gate Solenoid Gate solenoid valve/ ON or OFF Operation sound of solenoid (clicking sound) can be heard

OK:

Operation of solenoid (clicking sound) can be heard




OK

2.PERFORM ACTIVE TEST USING TECHSTREAM (REAR LEVELING SOLENOID)

NG

REPLACE NO. 2 HEIGHT CONTROL VALVE SUB-ASSEMBLY

2.PERFORM ACTIVE TEST USING TECHSTREAM (REAR LEVELING SOLENOID)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON, and turn the Techstream main switch on.


c.

Enter the following menus: Chassis / Air suspension / Active Test.

Air Suspension
Tester Display Test Part Control Range Diagnostic Note
Rear Leveling Solenoid Leveling solenoid valve ON or OFF Operation sound of solenoid (clicking sound) can be heard

OK:

Operation of solenoid (clicking sound) can be heard




OK

3.PERFORM ACTIVE TEST USING TECHSTREAM (EXHAUST SOLENOID)

NG

REPLACE NO. 2 HEIGHT CONTROL VALVE SUB-ASSEMBLY

3.PERFORM ACTIVE TEST USING TECHSTREAM (EXHAUST SOLENOID)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON, and turn the Techstream main switch on.


c.

Enter the following menus: Chassis / Air suspension / Active Test.

Air Suspension
Tester Display Test Part Control Range Diagnostic Note
Exhaust Solenoid Exhaust solenoid valve ON or OFF Operation sound of solenoid (clicking sound) can be heard

OK:

Operation of solenoid (clicking sound) can be heard




OK

4.INSPECT NO. 1 HEIGHT CONTROL COMPRESSOR (EXHAUST SOLENOID VALVE)

NG

REPLACE NO. 1 HEIGHT CONTROL COMPRESSOR

4.INSPECT NO. 1 HEIGHT CONTROL COMPRESSOR (EXHAUST SOLENOID VALVE)
a.

Turn the ignition switch off.


b.
C165645E10
1.458,2.042 0.948,2.583 0.948,2.583 0.948,2.76 true 1.948,2.042 2.458,2.583 2.458,2.583 2.458,2.76 true 0.917,2.792 1.083,3.021 0.167,0.229 10 false 2 2.438,2.792 2.625,2.958 0.188,0.167 10 false 1 0.208,0.094 2.688,0.76 2.479,0.667 10 false Component without harness connected: (Exhaust Valve)

Disconnect Q3 solenoid valve connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 10 to 14 Ω



d.

Connect the battery positive (+) lead to terminal 1 and the negative (-) lead to terminal 2 of the solenoid valve connector. Then check that the valve makes an operating sound.

OK:

Operation of solenoid (clicking sound) can be heard




OK

5.CHECK HARNESS AND CONNECTOR (EXHAUST SOLENOID VALVE - ECU AND BODY GROUND)

NG

REPLACE NO. 1 HEIGHT CONTROL COMPRESSOR

5.CHECK HARNESS AND CONNECTOR (EXHAUST SOLENOID VALVE - ECU AND BODY GROUND)
a.

Disconnect the O18 ECU connector.

C353464E01
0.854,0.813 1.198,1.021 0.344,0.208 4.49,1.365 4.833,1.573 0.344,0.208 1.365,2.26 0.844,1.854 true 0.396,0.063 2.75,0.708 2.354,0.646 10 false Rear view of wire harness connector: (to Suspension Control ECU) 1.375,2.271 2.604,2.469 1.229,0.198 10 false 9 (SLEX) 4.219,0.073 6.615,0.729 2.396,0.656 10 false Front view of wire harness connector: (to Exhaust Solenoid Valve) 4.573,1.396 4.885,1.594 0.313,0.198 10 false Q3 0.906,0.844 1.365,1.042 0.458,0.198 10 false O18


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q3-1 - O18-9 (SLEX) Always Below 1 Ω
Q3-1 or O18-9 (SLEX) - Body ground Always 10 kΩ or higher
Q3-2 - Body ground Always Below 1 Ω




OK

REPLACE SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR