Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM
RM27L0U _53 Suspension _049315 SUSPENSION CONTROL _0235712 AIR SUSPENSION SYSTEM C

SUSPENSION CONTROL  AIR SUSPENSION SYSTEM  C1792  Height Control Switch Circuit (Test Mode DTC)  


DESCRIPTION

Vehicle height can be chosen by pressing the height control switch.

By pressing the "UP" side, vehicle height goes up.

By pressing the "DOWN" side, vehicle height goes down.

DTC Code Detection Condition Trouble Area
C1792 Height control switch signal does not change.
·

Height control switch (No. 1 absorber control switch)

·

Wire harness or connector

·

Suspension control ECU



HINT:

This DTC is output only when the sensor signal check is done.


WIRING DIAGRAM

C180262E04
5.284,1.218 5.597,1.402 0.313,0.184 10 O16 5.284,0.548 5.597,0.731 0.313,0.184 10 O16 5.169,2.326 6.770,2.509 1.601,0.184 10 Suspension Control ECU 2.502,1.625 2.815,1.809 0.313,0.184 10 H72 3.799,1.123 3.934,1.306 0.136,0.184 10 4 3.799,0.456 3.934,0.639 0.136,0.184 10 5 5.351,1.003 5.563,1.187 0.212,0.184 10 14 5.351,0.337 5.563,0.520 0.212,0.184 10 15 5.699,1.213 6.173,1.396 0.474,0.184 10 DNSW 5.699,0.546 6.173,0.730 0.474,0.184 10 UPSW 3.355,1.126 3.742,1.309 0.387,0.184 10 LSW 3.355,0.459 3.742,0.643 0.387,0.184 10 HSW 2.646,0.781 2.795,0.965 0.149,0.184 10 E 2.997,0.472 3.188,0.656 0.190,0.184 10 HI 3.016,1.245 3.236,1.429 0.219,0.184 10 LO 2.459,0.791 2.594,0.974 0.136,0.184 10 6 2.493,1.807 4.275,2.175 1.781,0.368 10 Height Control Switch (No. 1 Absorber Control Switch)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the suspension control ECU, perform registration (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>REGISTRATION).


PROCEDURE

1.READ VALUE USING TECHSTREAM (HEIGHT CONTROL SWITCH)
a.

Turn the ignition switch off.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON, and turn the Techstream main switch on.


d.

Enter the following menus: Chassis / Air suspension / Data List.

Air Suspension
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Height Control Switch(Up) Height control switch (Up) / ON or OFF ON: Height control switch "UP" button pressed
OFF: -
-
Height Control Switch(Down) Height control switch (Down) / ON or OFF ON: Height control switch "DOWN" button pressed
OFF: -
-


e.

Check that the value displayed on the Techstream changes by pressing the height control switch "UP" or "DOWN".

OK:

Height control switch value changes.


Result
Result Proceed to
NG A
OK (When troubleshooting according to the Problem Symptoms Table) B
OK (When troubleshooting according to the DTC Chart) C



A

2.INSPECT HEIGHT CONTROL SWITCH

B

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C

2.INSPECT HEIGHT CONTROL SWITCH
a.

Turn the ignition switch off.


b.
C179509E01
2.433,3.923 2.835,4.098 0.402,0.175 10 Down 2.433,2.84 2.835,3.016 0.402,0.175 10 Up 1.482,2.273 1.902,2.449 0.420,0.176 10 HSW 2.066,2.273 2.486,2.449 0.420,0.176 10 LSW 1.109,2.264 1.247,2.440 0.138,0.176 10 E 0.171,0.072 2.719,0.598 2.548,0.526 10 Component without harness connected: (Height Control Switch) 1.632,1.712 1.677,2.267 false 1.449,1.706 1.18,2.243 false 1.835,1.705 2.2,2.239 false 2.375,2.945 2.062,3.127 false 2.42,3.994 2.108,3.883 false

Remove the height control switch.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (LSW) - 6 (E) Down operation Below 1 Ω
4 (LSW) - 6 (E) Up operation 10 kΩ or higher
5 (HSW) - 6 (E) Down operation 10 kΩ or higher
5 (HSW) - 6 (E) Up operation Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (HEIGHT CONTROL SWITCH - ECU AND BODY GROUND)

NG

REPLACE NO. 1 ABSORBER CONTROL SWITCH

3.CHECK HARNESS AND CONNECTOR (HEIGHT CONTROL SWITCH - ECU AND BODY GROUND)
a.

Disconnect the O16 ECU connector.

C353469E01
2.385,0.885 2.708,1.094 0.323,0.208 5.333,0.719 5.656,0.927 0.323,0.208 5.24,1.927 5.417,1.708 true 5.625,1.927 5.573,1.708 true 6.052,1.938 5.708,1.698 true 1.823,2.417 2.375,2.052 true 2.792,2.448 2.438,2.063 true 4.146,0.073 6.5,0.729 2.354,0.656 10 false Front view of wire harness connector: (to Height Control Switch) 0.385,0.052 2.74,0.708 2.354,0.656 10 false Rear view of wire harness connector: (to Suspension Control ECU) 2.427,0.917 2.885,1.115 0.458,0.198 10 false O16 1.438,2.448 2.813,2.646 1.375,0.198 10 false 15 (UPSW) 2.458,2.458 3.833,2.656 1.375,0.198 10 false 14 (DNSW) 5.031,1.948 5.49,2.146 0.458,0.198 10 false LSW 5.479,1.948 5.938,2.146 0.458,0.198 10 false HSW 6.083,1.948 6.24,2.146 0.156,0.198 10 false E 5.375,0.75 5.833,0.948 0.458,0.198 10 false H72


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H72-5 (HSW) - O16-15 (UPSW) Always Below 1 Ω
H72-4 (LSW) - O16-14 (DNSW) Always Below 1 Ω
H72-6 (E) - Body ground Always Below 1 Ω
H72-5 (HSW) or O16-15 (UPSW) - Body ground Always 10 kΩ or higher
H72-4 (LSW) or O16-14 (DNSW) - Body ground Always 10 kΩ or higher




OK

REPLACE SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR