Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM
RM27L0U _53 Suspension _049315 SUSPENSION CONTROL _0235712 AIR SUSPENSION SYSTEM C

SUSPENSION CONTROL  AIR SUSPENSION SYSTEM  C1793  Height Control Off Switch Circuit  


DESCRIPTION

Height control can be operated or suspended by pressing the height control mode select switch.

By pressing the switch once, height control can be suspended.

By pressing the switch one more time, height control can be operated.

DTC Code Detection Condition Trouble Area
C1793 Height control mode select switch signal does not change.
·

Height control mode select switch (No. 2 absorber control switch)

·

Wire harness or connector

·

Suspension control ECU



HINT:

This DTC is output only when the sensor signal check is done.


WIRING DIAGRAM

C180264E02
5.277,0.79 5.590,0.973 0.313,0.184 10 O16 5.169,2.326 6.770,2.509 1.601,0.184 10 Suspension Control ECU 2.016,1.139 2.329,1.323 0.313,0.184 10 H73 3.799,0.689 3.934,0.873 0.136,0.184 10 6 5.335,0.568 5.547,0.752 0.212,0.184 10 13 5.699,0.783 5.983,0.967 0.284,0.184 10 TD 2.196,0.69 2.332,0.874 0.136,0.184 10 3 2.008,1.322 4.206,1.695 2.198,0.374 10 Height Control Mode Select Switch (No. 2 Absorber Control Switch)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the suspension control ECU, perform registration (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>REGISTRATION).


PROCEDURE

1.READ VALUE USING TECHSTREAM (MANUAL MODE SWITCH)
a.

Turn the ignition switch off.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON, and turn the Techstream main switch on.


d.

Enter the following menus: Chassis / Air suspension / Data List.

Air Suspension
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Manual Mode Switch Height control mode select switch (Manual)/ ON or OFF ON: Height control mode select switch ON condition
OFF: Height control mode select switch OFF condition
-


e.

Check that the value displayed on the Techstream changes by pressing the height control mode select switch.

OK:

Height control mode select switch value changes.


Result
Result Proceed to
NG A
OK (When troubleshooting according to the Problem Symptoms Table) B
OK (When troubleshooting according to the DTC Chart) C



A

2.INSPECT HEIGHT CONTROL MODE SELECT SWITCH

B

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C

2.INSPECT HEIGHT CONTROL MODE SELECT SWITCH
a.

Turn the ignition switch off.


b.
C179512E02
2.565,3.343 3.139,3.594 0.574,0.251 10 Pushed 0.171,0 2.874,0.526 2.703,0.526 10 Component without harness connected: (Height Control Mode Select Switch)

Remove the height control mode select switch.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 - 6 Free 10 kΩ or higher
3 - 6 Pushed in Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (HEIGHT CONTROL MODE SELECT SWITCH - ECU AND BODY GROUND)

NG

REPLACE NO. 2 ABSORBER CONTROL SWITCH

3.CHECK HARNESS AND CONNECTOR (HEIGHT CONTROL MODE SELECT SWITCH - ECU AND BODY GROUND)
a.

Disconnect the O16 ECU connector.

C353470E01
2.385,0.906 2.708,1.125 0.323,0.219 5.073,0.802 5.396,1.021 0.323,0.219 2.073,2.396 2.49,2.083 true 0.448,0.083 2.771,0.771 2.323,0.688 10 false Rear view of wire harness connector: (to Suspension Control ECU) 4.083,0.104 6.5,0.823 2.417,0.719 10 false Front view of wire harness connector: (to Height Control Mode Select Switch) 2.427,0.948 2.885,1.146 0.458,0.198 10 false O16 1.854,2.417 2.927,2.615 1.073,0.198 10 false 13 (TD) 5.115,0.833 5.573,1.031 0.458,0.198 10 false H73


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H73-6 - O16-13 (TD) Always Below 1 Ω
H73-3 - Body ground Always Below 1 Ω
H73-6 or O16-13 (TD) - Body ground Always 10 kΩ or higher




OK

REPLACE SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR