Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM
RM27L0U _53 Suspension _049319 TIRE PRESSURE MONITORING _0235729 TIRE PRESSURE WARNING SYSTEM J

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This is the power source for the tire pressure warning ECU.

WIRING DIAGRAM

C180358E03
2.24,3.302 3.188,3.49 0.948,0.188 10 false Ignition Switch 2.177,2.813 2.573,2.969 0.396,0.156 10 false AM1 1.365,2.854 1.76,3.01 0.396,0.156 10 false AM1 2.958,2.802 3.292,2.99 0.333,0.188 10 false IG1 1.99,2.594 2.135,2.781 0.146,0.188 10 false 4 1.313,1.865 2.813,2.063 1.5,0.198 10 false IG No. 1 (Built-in Relay) 3.25,2.594 3.438,2.781 0.188,0.188 10 false 1 3.146,0.802 4.021,1.031 0.875,0.229 10 false ECU-IG No. 1 5.188,0.552 5.417,0.75 0.229,0.198 10 false 7 5.177,2.125 5.375,2.323 0.198,0.198 10 false 9 5.406,0.646 5.635,0.813 0.229,0.167 10 false IG 5.396,2.229 5.771,2.458 0.375,0.229 10 false GND 2.26,3.917 3.083,4.146 0.823,0.229 10 false from Battery 4.844,3.625 6.625,3.813 1.781,0.188 10 false Tire Pressure Warning ECU 4.844,3.448 5.219,3.625 0.375,0.177 10 false H40 2.24,3.156 2.635,3.313 0.396,0.156 10 false H10

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU, read the transmitter IDs stored in the old ECU using the Techstream and write them down before removal.

·

It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU after the ECU and/or tire pressure warning valve and transmitter has been replaced.



PROCEDURE

1.INSPECT FUSE (ECU-IG NO. 1)
a.
B443281E01
2.188,1.792 2.448,1.271 true 0.125,0.094 1.208,0.292 1.083,0.198 10 false Main Body ECU: 1.333,1.771 2.198,1.948 0.865,0.177 10 false ECU-IG No. 1

Remove the ECU-IG No. 1 fuse from the main body ECU.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ECU-IG No. 1 fuse Always Below 1 Ω




OK

2.CHECK HARNESS AND CONNECTOR (ECU - BATTERY AND BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (ECU - BATTERY)
2.CHECK HARNESS AND CONNECTOR (ECU - BATTERY AND BODY GROUND)
a.

Disconnect the H40 ECU connector.


b.
U153422E02
1.781,2.656 2.479,3 false 1.333,2.635 0.75,2.896 false 0.25,0.125 2.646,0.667 2.396,0.542 10 false Front view of wire harness connector: (to Tire Pressure Warning ECU) 0.635,2.313 0.906,2.479 0.271,0.167 10 false H40 0.573,2.844 0.885,3.031 0.313,0.188 10 false IG 2.521,2.927 3,3.135 0.479,0.208 10 false GND

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H40-7 (IG) - Body ground Ignition switch ON 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
H40-9 (GND) - Body ground Always Below 1 Ω




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ECU - BATTERY)
a.

Disconnect the H40 ECU connector.


b.
U153423E02
1.344,2.646 0.719,2.875 false 0.25,0.135 2.656,0.677 2.406,0.542 10 false Front view of wire harness connector: (to Tire Pressure Warning ECU) 0.635,2.313 0.906,2.479 0.271,0.167 10 false H40 0.542,2.823 0.854,3.01 0.313,0.188 10 false IG

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H40-7 (IG) - Body ground Always 10 kΩ or higher




OK

REPLACE FUSE

NG

CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE