Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM
RM27L0U _53 Suspension _049319 TIRE PRESSURE MONITORING _0235729 TIRE PRESSURE WARNING SYSTEM J

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  Tire Pressure Warning Reset Switch Circuit  


DESCRIPTION

Initialization can be started by pressing the tire pressure warning reset switch and holding it for 3 seconds or more.

If the ECU receives the signal from the switch, the tire pressure warning light blinks 3 times (1 second on, 1 second off).

WIRING DIAGRAM

C140098E43
1.895,1.325 4.155,1.502 2.260,0.177 10 Tire Pressure Warning Reset Switch 2.273,0.499 2.415,0.655 0.142,0.156 10 2 3.779,0.492 3.928,0.641 0.149,0.149 10 1 5.467,0.604 5.957,0.753 0.489,0.149 10 CLSW 5.075,2.187 6.814,2.357 1.739,0.170 10 Tire Pressure Warning ECU 5.075,1.991 5.436,2.175 0.361,0.184 10 H40 5.233,0.513 5.355,0.659 0.123,0.147 10 1 1.895,1.119 2.172,1.271 0.277,0.152 10 H52

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU, read the transmitter IDs stored in the old ECU using the Techstream and write them down before removal.

·

It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU, after the ECU and/or tire pressure warning valve and transmitter has been replaced.



PROCEDURE

1.CHECK TIRE PRESSURE WARNING RESET SWITCH FUNCTION
a.

Perform the tire pressure warning reset switch test in Test Mode Procedure (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>TEST MODE PROCEDURE).

OK:
Switch Condition Specified Condition
Tire pressure warning reset switch ON Tire pressure warning light turns on.
Tire pressure warning reset switch OFF Tire pressure warning light blinks.




OK

NG

2.INSPECT TIRE PRESSURE WARNING RESET SWITCH
2.INSPECT TIRE PRESSURE WARNING RESET SWITCH
a.
C158396E11
2.667,2.406 2.552,2.771 false 2.938,2.406 3.052,2.771 false 0.167,0.208 2.646,0.677 2.479,0.469 10 false Component without harness connected: (Tire Pressure Warning Reset Switch) 1.531,2.344 1.771,2.531 0.24,0.188 10 false ON 1.521,2.917 1.906,3.115 0.385,0.198 10 false OFF 2.479,2.823 2.667,2.99 0.188,0.167 10 false 2 3.042,2.823 3.25,3 0.208,0.177 10 false 1

Remove the tire pressure warning reset switch (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RESET SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 ON (Switch is pressed and held) Below 1 Ω
OFF (Switch is not pressed) 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (RESET SWITCH - ECU AND BODY GROUND)

NG

REPLACE TIRE PRESSURE WARNING RESET SWITCH

3.CHECK HARNESS AND CONNECTOR (RESET SWITCH - ECU AND BODY GROUND)
a.

Disconnect the H52 reset switch connector.


b.

Disconnect the H40 ECU connector.


c.
C353182E02
0.677,1.281 1.083,1.49 0.406,0.208 0.677,3.656 1.083,3.865 0.406,0.208 1.917,3.958 2.146,3.865 false 0.146,0.156 2.427,0.375 2.281,0.219 10 false Front view of wire harness connector: 0.156,2.01 2.385,2.406 2.229,0.396 10 false Rear view of wire harness connector: (to Tire Pressure Warning ECU) 0.135,0.323 2.656,0.521 2.521,0.198 10 false (to Tire Pressure Warning Reset Switch) 0.75,1.302 1.063,1.479 0.313,0.177 10 false H52 0.76,3.677 1.073,3.854 0.313,0.177 10 false H40 2.198,3.76 2.844,3.958 0.646,0.198 10 false 1 (CLSW)

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H40-1 (CLSW) - H52-1 Always Below 1 Ω
H40-1 (CLSW) - Body ground Always 10 kΩ or higher
H52-2 - Body ground Always Below 1 Ω




OK

REPLACE TIRE PRESSURE WARNING ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR