The transmitter IDs of each tire pressure warning valve and transmitter are registered to the tire pressure warning ECU.
When the IDs have never been registered, a DTC is stored.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C2171/71 | Transmitter ID is not registered (when a transmitter ID is unregistered for 3 minutes or more). | Tire pressure warning ECU |
When replacing the tire pressure warning ECU, read the transmitter IDs stored in the old ECU using the Techstream and note them down before removal.
It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU after the ECU has been replaced.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item/Display | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Registered ID1 Code | Registered ID1 code/
min.: 0 max.: FFFFFFFF* |
The transmitter ID registered in the transmitter ID1 is displayed | *: Displayed only when the transmitter ID is not registered. |
| Registered ID2 Code | Registered ID2 code/
min.: 0 max.: FFFFFFFF* |
The transmitter ID registered in the transmitter ID2 is displayed | *: Displayed only when the transmitter ID is not registered. |
| Registered ID3 Code | Registered ID3 code/
min.: 0 max.: FFFFFFFF* |
The transmitter ID registered in the transmitter ID3 is displayed | *: Displayed only when the transmitter ID is not registered. |
| Registered ID4 Code | Registered ID4 code/
min.: 0 max.: FFFFFFFF* |
The transmitter ID registered in the transmitter ID4 is displayed | *: Displayed only when the transmitter ID is not registered. |
| Result | Proceed to |
|---|---|
| The registered transmitter IDs are not displayed on the Techstream screen. | A |
| The registered transmitter IDs are displayed on the Techstream screen. | B |
A
B
Register the transmitter IDs for all 4 tires (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION).
NEXT
Perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION).
NEXT
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| ID 1 Tire Inflation Pressure | ID1 tire inflation pressure /
min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure / 449.35 kPa (4.6 kgf/cm2, 65 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi) |
Actual tire inflation pressure | If 100 kPa (1 kgf/cm2, 14 psi) is displayed for absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for relative pressure, data has not been received*. |
| ID 2 Tire Inflation Pressure | ID2 tire inflation pressure /
min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure / 449.35 kPa (4.6 kgf/cm2, 65 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi) |
Actual tire inflation pressure | If 100 kPa (1 kgf/cm2, 14 psi) is displayed for absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for relative pressure, data has not been received*. |
| ID 3 Tire Inflation Pressure | ID3 tire inflation pressure /
min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure / 449.35 kPa (4.6 kgf/cm2, 65 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi) |
Actual tire inflation pressure | If 100 kPa (1 kgf/cm2, 14 psi) is displayed for absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for relative pressure, data has not been received*. |
| ID 4 Tire Inflation Pressure | ID4 tire inflation pressure /
min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure / 449.35 kPa (4.6 kgf/cm2, 65 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi) |
Actual tire inflation pressure | If 100 kPa (1 kgf/cm2, 14 psi) is displayed for absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for relative pressure, data has not been received*. |
*: It may take about 5 to 6 minutes until the values are displayed.
When no "ID Tire Inflation Pressure" has changed, rotate the tire 90 to 270°. Then recheck it.
| Result | Proceed to |
|---|---|
| All tire pressure readings are equal to specified values. | A |
| Tire pressure values are not displayed. | B |
A
B