Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL
RM27L0U _54 Brake _049322 BRAKE SYSTEM (OTHER) _0235745 BRAKE PEDAL N

BRAKE SYSTEM (OTHER)  BRAKE PEDAL  ADJUSTMENT  


PROCEDURE

Hide 47101 1.CHECK BRAKE PEDAL HEIGHT

a.

Check the brake pedal height.

i.

Turn back the carpet.


ii.

Remove the tibia pad.


iii.
C208542E03
2.24,2.292 1.51,2.823 1.51,2.823 1.354,2.823 true 1.792,3.635 1.063,3.635 false 1.896,3.354 1.417,3.354 1.417,3.354 1.417,3.635 false 0.25,2.74 1.385,3.083 1.135,0.344 10 false Stop Light Switch 1.865,4.188 2.698,4.521 0.833,0.333 10 false Pedal Height 0.302,3.563 1.031,3.906 0.729,0.344 10 false Dash Panel

Measure the shortest distance between the brake pedal surface and dash panel.

Standard pedal height from dash panel:

179.9 to 189.9 mm (7.08 to 7.48 in.)


NOTICE:

Do not adjust the pedal height. Doing so by changing the push rod length will structurally change the pedal ratio.


If the pedal height is incorrect, check that there is no damage in the brake pedal, brake pedal lever, brake pedal bracket and dash panel.

Even if there is damage, there is no problem if the reserve distance is within the standard value. If necessary, replace these parts.



Hide 84340 2.CHECK AND ADJUST STOP LIGHT SWITCH ASSEMBLY

HINT:

If the pedal height is incorrect, check and adjust the stop light switch clearance.


a.

Disconnect the stop light switch connector.


b.

Turn the stop light switch counterclockwise and remove it.


c.
U153434E01
0.469,1.802 1.333,2.125 0.865,0.323 10 false 1.5 to 2.5 mm 1.219,0.083 2.323,0.438 1.104,0.354 10 false Stop Light Switch

Insert the stop light switch until the body hits the cushion.

NOTICE:

When inserting the stop light switch, support the pedal from behind so that the pedal is not pushed in.



d.

Make a quarter turn clockwise to install the stop light switch.

HINT:

Due to the inverse screw structure, if the stop light switch is turned clockwise, the stop light switch moves in the direction to be pulled out.


NOTICE:

The turning torque for installing the stop light switch should be 1.5 N*m (15 kgf*cm, 13 in.*lbf) or less.



e.

Connect the stop light switch connector.


f.

Check the protrusion of the rod.

Standard protrusion of the rod:

1.5 to 2.5 mm (0.0591 to 0.0984 in.)



Hide 47101 3.CHECK PEDAL FREE PLAY

a.
C208541E01
2.619,3.635 3.243,3.971 0.623,0.336 10 Pedal Free Play

Stop the engine and depress the brake pedal several times until there is no more vacuum left in the booster.


b.

Push in the brake pedal until the beginning of the resistance is felt. Measure the distance as shown in the illustration.

Standard pedal free play:

1.0 to 6.0 mm (0.0394 to 0.236 in.)



Hide 47101 4.CHECK PEDAL RESERVE DISTANCE

a.

Release the parking brake pedal.


b.
R000934E39
1.927,1.5 2.854,1.823 0.927,0.323 10 false Pedal Reserve Distance

With the engine running, depress the brake pedal and measure the pedal reserve distance as shown in the illustration.

Standard pedal reserve distance from asphalt sheet at 490 N (50 kgf, 110.2 lbf):

More than 104 mm (4.09 in.)


If incorrect, troubleshoot the brake system (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).