Home › Brake › PARKING BRAKE › PARKING BRAKE SYSTEM
RM27L0U _54 Brake _049325 PARKING BRAKE _0235754 PARKING BRAKE SYSTEM N

PARKING BRAKE  PARKING BRAKE SYSTEM  ADJUSTMENT  


PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 2.ADJUST PARKING BRAKE SHOE CLEARANCE

a.

Temporarily install the hub nuts.


b.

Remove the hole plug.


c.
C158874E03
1.781,0.313 1.99,0.458 0.208,0.146 10 false (X) 1.698,1.063 1.927,1.271 0.229,0.208 10 true (Y)

Insert a screwdriver into the adjustment hole of the disc. Rotate the adjustment wheel in the "X" direction until the shoes are locked. Then rotate the adjustment wheel in the "Y" direction 8 notches.


d.

Check that the disc can be rotated smoothly. If not, rotate the adjustment wheel in the "Y" direction and check again.


e.

Install the hole plug.


f.

Remove the hub nuts.


Hide 3.INSTALL REAR WHEEL

Torque:
for Aluminum Wheel : 131 N*m (1336 kgf*cm, 97 ft.*lbf)
for Steel Wheel : 209 N*m (2131 kgf*cm, 154 ft.*lbf)

Hide 4.CHECK PARKING BRAKE PEDAL TRAVEL

a.

Firmly depress the parking brake pedal.


b.

Release the parking brake.


c.

Slowly depress the parking brake pedal with a force of approximately 300 N (31 kgf, 67.4 lbf) and count the number of clicks.

Standard:

6 to 9 clicks



Hide 5.ADJUST PARKING BRAKE PEDAL TRAVEL

a.

Depress the parking brake pedal.


b.

Release the parking brake pedal to the original position.


c.
C208921

Loosen the pedal side No. 1 parking brake cable lock nut.


d.

Turn the pedal side No. 1 parking brake cable adjustment nut until the parking brake pedal travel is correct.

Standard Parking Brake Pedal Travel:
Pedal Load Specified Condition
300 N (31 kgf, 67.4 lbf) 6 to 9 clicks



e.

Using a wrench or equivalent to hold the adjustment nut, tighten the lock nut.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

Pay attention that the adjustment nut does not rotate with the lock nut during tightening.



f.

Additionally, excessive pedal travel can be adjusted on the No. 1 parking brake cable underbody side as follows.

i.

Release the parking brake pedal to the original position.


ii.
U153668E02
2,1.583 2,0.885 2,0.885 1.469,0.885 false 0.802,1.708 0.802,2.833 false 0.458,0.823 1.49,1.146 1.031,0.323 10 false Adjustment Nut 0.281,2.854 2.031,3.177 1.75,0.323 10 false No. 1 Parking Brake Cable 1.146,0.344 1.76,0.656 0.615,0.313 10 false Lock Nut

Loosen the underbody side No. 1 parking brake cable lock nut.


iii.

Turn the underbody side No. 1 parking brake cable adjustment nut until the parking brake pedal travel is correct.

Standard Parking Brake Pedal Travel:
Pedal Load Specified Condition
300 N (31 kgf, 67.4 lbf) 6 to 9 clicks



iv.

Tighten the No. 1 parking brake cable underbody lock nut.

Torque:
13 N*m (128 kgf*cm, 9 ft.*lbf)

NOTICE:

Pay attention that the adjustment nut does not rotate with the lock nut during tightening.




g.

Depress to full stroke and release the parking brake pedal 3 or 4 times. Then check the number of clicks when depressing the pedal.

Standard:

6 to 9 clicks


If the result is not as specified, adjust the parking brake pedal travel again.


h.

Check whether the parking brake drags or not.

If the parking brake drags, adjust the shoe clearance.


i.

When operating the parking brake pedal, check that the parking brake pedal indicator light comes on at the first notch.

If not, adjust the parking brake switch installation position.