Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049329 AUDIO / VIDEO _0235782 AUDIO AND VISUAL SYSTEM C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  B158A  Extension Module Noise Adjustment Malfunction  B15FE  XM Tuner Antenna Disconnected  B15FF  XM Tuner Antenna Short  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the satellite radio antenna which is connected to the radio and display assembly.

DTC Code DTC Detection Condition Trouble Area
B158A Noise adjustment is malfunction.
·

Satellite radio antenna assembly

·

Amplifier antenna assembly

·

Antenna cord sub-assembly

·

Stereo component tuner assembly

·

Radio and display receiver assembly


B15FE Satellite radio antenna is not connected.
B15FF A short occurs in satellite radio antenna.

WIRING DIAGRAM

E283175E04
5.917,2.25 6.375,2.448 0.458,0.198 10 false SD 5.917,2.448 7.094,3.104 1.177,0.656 10 false Stereo Component Tuner Assembly 0.229,1.469 1.406,2.063 1.177,0.594 10 false Satellite Radio Antenna Assembly 1.417,2.156 2.51,2.885 1.094,0.729 10 false Amplifier Antenna Assembly 5.458,1.094 5.917,1.292 0.458,0.198 10 false 1 5.344,1.365 5.802,1.563 0.458,0.198 10 false 1-1 2.292,1.083 2.75,1.281 0.458,0.198 10 false 9 2.302,1.365 2.76,1.563 0.458,0.198 10 false 9-1 3.563,2.25 4.469,2.771 0.906,0.521 10 false Antenna Cord Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Some satellite radio broadcasts require payment. A contract must be made between a satellite radio company and the user. If the contract expires, it will not be possible to listen to the broadcast.


·

After replacing the stereo component tuner assembly of vehicles subscribed to pay-type satellite radio broadcasts, XM radio ID registration is necessary.



PROCEDURE

1.CHECK CONNECTION OF SATELLITE RADIO ANTENNA CABLE
a.

Check if the satellite radio antenna cable is securely connected to the stereo component tuner assembly.

OK:

Satellite radio antenna cable is securely connected.




OK

2.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

SECURELY CONNECT SATELLITE RADIO ANTENNA CABLE

2.CHECK ANTENNA CORD SUB-ASSEMBLY
a.
U154196E02
2.563,0.948 2.74,0.49 2.74,0.49 2.969,0.49 true 1.802,2.625 2.042,2.406 2.042,2.406 2.26,2.406 true 0.24,1.958 0.479,2.198 0.24,0.24 10 false *b 0.24,0.135 0.479,0.375 0.24,0.24 10 false *a 3,0.406 3.302,0.646 0.302,0.24 10 false 9-1 2.313,2.333 2.615,2.573 0.302,0.24 10 false 1-1 1.021,2.49 1.292,2.667 0.271,0.177 10 false SD

Disconnect the stereo component tuner assembly connector.


b.

Disconnect the antenna connector from the amplifier antenna assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
SD-1 - 9 Always Below 1 Ω
SD-1-1 - 9-1 Always Below 1 Ω
SD-1 - Body ground Always 10 kΩ or higher
SD-1-1 - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Amplifier Antenna Assembly)
*b Front view of wire harness connector
(to Stereo Component Tuner Assembly)



OK

3.CHECK SATELLITE RADIO ANTENNA ASSEMBLY

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY

3.CHECK SATELLITE RADIO ANTENNA ASSEMBLY

OK

END (SATELLITE RADIO ANTENNA ASSEMBLY IS DEFECTIVE)

NG

4.CHECK AMPLIFIER ANTENNA ASSEMBLY
4.CHECK AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the amplifier antenna assembly.


b.

Check if radio broadcasts can be received normally.

OK:

Radio broadcasts can be received normally.




OK

END (AMPLIFIER ANTENNA ASSEMBLY IS DEFECTIVE)

NG

5.CHECK STEREO COMPONENT TUNER ASSEMBLY
5.CHECK STEREO COMPONENT TUNER ASSEMBLY

OK

END (STEREO COMPONENT TUNER ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY