Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM27L0U _56 Audio / Visual / Telematics _049330 NAVIGATION / MULTI INFO DISPLAY _0235785 NAVIGATION SYSTEM D

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  OPERATION CHECK  


CHECK NAVIGATION SYSTEM NORMAL CONDITION


a.

If the cause of a symptom is any of the following, the corresponding symptom is normal; it is not a malfunction.

Symptom Answer
A longer route than expected is chosen. Depending on the road conditions, the navigation receiver assembly may determine that a longer route is quicker.
Even when distance priority is high, the shortest route is not shown. Some routes may not be advised due to safety concerns.
When the vehicle is put into motion immediately after the engine starts, the navigation system deviates from the correct position. If the vehicle starts before the navigation system activates, the system may not react.
When driving on certain types of roads, especially new roads, the vehicle position deviates from the correct position. When the vehicle is driving on new roads not available on the SD card, the system attempts to match it to another nearby road, causing the position mark to deviate.


b.
I100066

The following symptoms are not malfunctions, but are caused by errors inherent in the GPS, gyro sensor, speed sensor or navigation receiver assembly.

i.

The current position mark may be displayed on a nearby parallel road.


ii.
I100067

Immediately after a fork in the road, the current vehicle position mark may be displayed on the wrong road.


iii.
I100068

When the vehicle turns right or left at an intersection, the current vehicle position mark may be displayed on a nearby parallel road.


iv.
I100069

When the vehicle is carried, such as on a ferry, and the vehicle itself is not driving, the current vehicle position mark may be displayed in the position where the vehicle was until a measurement can be performed by the GPS.


v.
I100070

When the vehicle travels on a steep hill, the current vehicle position mark may deviate from the correct position.


vi.
I100071

When the vehicle makes a continuous turn (e.g. 360, 720, 1080 degrees), the current vehicle position mark may deviate from the correct position.


vii.
I100072

When the vehicle moves erratically, such as constant lane changes, the current vehicle position mark may deviate from the correct position.


viii.
E106418

When the ignition switch is turned to ACC or ON and the vehicle is turned on a turntable before parking, the current vehicle position mark may not indicate the correct direction. The same will occur when the vehicle comes out of the parking garage.


ix.
I100074

When the vehicle travels on a snowy road or a mountain path with tire chains installed or using a spare tire, the current vehicle position mark may deviate from the correct position.


x.
I100075

When the tires are changed, the current vehicle position mark may deviate from the correct position.

HINT:
·

A change in tire diameter may cause a speed sensor error.

·

Performing "tire change" in calibration mode will allow the system to correct the current vehicle position faster.






CHECK SD CARD


HINT:
·

Check the SD card installed into the navigation receiver assembly.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E273697

Select "Failure Diagnosis" from the "Service Menu" screen.


c.
E277993

Select "SD Check" from the "Failure Diagnosis" screen.


d.
E273699E01
3.107,0.704 3.332,0.883 0.225,0.179 10 *a 2.823,0.821 3.092,0.821 false

SD Check

i.

Select "SD Check" to start the SD card check.


ii.

Check that the result is displayed when the SD check is completed.

Screen Description
Display (Result) Description
Checking Check is in progress
OK SD card is normal
NG SD card is malfunctioning

Text in Illustration
*a Result

HINT:
·

After selecting "SD Check", it may take a while until the result is displayed.

·

If the cabin temperature is -20°C (-4°F) or lower, or 65°C (149°F) or higher, the SD card may not operate normally, and "NG" may be shown on the display. Make sure to perform the inspection with the cabin at an appropriate temperature.

·

If "NG" is displayed even when the cabin temperature is appropriate, replace the SD card with a new one.






CHECK PANEL & STEERING SWITCH


HINT:
·

The navigation receiver assembly panel switches and steering switches are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E273700

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E280376

Select "Panel & Steering Switch" from the "Function Check/Setting I" screen.


d.
E225786E01
2.269,1.407 3.085,1.407 false 0.344,1.149 1.04,1.149 false 2.888,1.063 3.085,1.063 false 0.148,1.048 0.304,1.200 0.156,0.152 10 *a 3.087,0.962 3.243,1.114 0.156,0.152 10 *b 3.087,1.327 3.243,1.480 0.156,0.152 10 *c

Panel & Steering Switch Check Mode

Screen Description
Display Content
*a: Switch condition "Pushed" is displayed when any switch is pushed
*b: Number of switches pushed
·

Number of switches pushed at once is displayed

·

If more than 3 switches are pushed at once, "More than 3" is displayed

·

If 4 or more switches are pushed at once, "More than 3" is displayed


*c: Rotary switch direction Direction of rotary switch is displayed

i.

Operate each switch and check that the switch conditions are correctly displayed.

NOTICE:

When the "APPS" switch is pressed and held for 3 seconds or more, diagnostic mode will be canceled.





CHECK TOUCH SWITCH


HINT:
·

The touch switches on the screen are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E273700

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E280876

Select "Touch Switch" from the "Function Check/Setting I" screen.


d.

Touch Switch Check

i.
E176521

Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.

HINT:
·

A "+" mark is displayed where the display is touched.

·

The "+" mark remains on the display even after the finger is removed.






CHECK MIC & VOICE RECOGNITION


HINT:
·

The microphone and microphone input level are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E273700

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E280877

Select "Microphone Check" from the "Function Check/Setting I" screen.


d.
E268457E20
2.281,0.844 2.563,0.198 true 2.875,1.344 3.052,1.344 true 2.406,1.427 2.406,1.865 true 2.063,1.427 2.063,1.844 true 1.729,1.417 1.729,1.833 true 2.604,0.031 2.813,0.24 0.208,0.208 10 false *a 3.094,1.24 3.302,1.448 0.208,0.208 10 false *e 2.354,1.896 2.563,2.104 0.208,0.208 10 false *d 1.99,1.885 2.198,2.094 0.208,0.208 10 false *c 1.646,1.885 1.854,2.094 0.208,0.208 10 false *b

Microphone Check

Screen Description
Display Content
*a: Microphone input level meter Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels.
*b: Recording switch Starts recording.
*c: Stop switch Stops recording and playing.
*d: Play switch Plays the recorded voice.
*e: Recording indicator Comes on while recording.

i.

When speaking into the microphone, check that the microphone input level meter changes according to the input level.

HINT:

The microphone is active at all times when this screen is displayed.



ii.

Push the recording switch and perform voice recording.

HINT:
·

Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.

·

While recording or playing, the switches other than the stop switch cannot be pushed.

·

When no recording is present, the play switch cannot be pushed.

·

Recording will stop after 5 seconds or when the stop switch is pushed.




iii.

Check that the recording indicator remains on while recording and that the recording can be played normally.




CHECK GPS & VEHICLE SENSORS


HINT:
·

GPS information, vehicle signals and sensor signals are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E273700

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E280878

Select "System Sensor Check" from the "Function Check/Setting I" screen.


d.
E273705E01
3.049,1.279 3.231,1.438 0.181,0.158 10 *d 0.213,0.54 0.395,0.699 0.181,0.158 10 *a 0.213,0.95 0.395,1.108 0.181,0.158 10 *b 0.213,1.185 0.395,1.343 0.181,0.158 10 *c 0.218,1.507 0.399,1.665 0.181,0.158 10 *e 0.58,0.632 0.391,0.632 false 0.403,1.053 0.594,1.053 false 0.4,1.288 0.511,1.288 false 0.403,1.6 0.609,1.6 false 2.849,1.38 3.035,1.38 false

System Sensor Check

*a: GPS
Display Content
Reception number Displays reception condition of the satellites used to determine vehicle position Blue: P (In use) System is using GPS signal for location.
Yellow: T (Receiving) System is tracking GPS signal for location.
No color: Not in use System cannot receive GPS signal. (Searching for GPS signal)
Status Displays reception status of the satellites used to determine vehicle position OK (H3D) High accuracy 3-dimensional location method is being used.
OK (H2D) High accuracy 2-dimensional location method is being used.
OK (3D) 3-dimensional location method is being used.
OK (2D) 2-dimensional location method is being used.
NG Location data cannot be used.
error Reception error has occurred.
- Any other state.
Measurement ratio Displays the ratio of satellites performing measurements 3D The ratio of satellites performing 3D positioning, Hyper 3D positioning and Hyper 2D positioning is displayed.
2D The ratio of satellites performing 2D positioning is displayed.
NG The ratio of satellites not performing measurement is displayed.
Date Date/time information obtained from GPS signals is displayed in Greenwich Mean Time (GMT).
Position Latitude and longitude information on current position is displayed.

*b: SPD
Display Content
Pulse count Displays the accumulated number of input pulses beginning when this screen is displayed
Speed Displays vehicle speed

*c: Sensor Signal
Display Content Note
Gyro Voltage Displays the output voltage of the gyro sensor -
0 point Voltage Displays the zero-point voltage of the gyro sensor -
Relative bearing Displays the output angle of the gyro sensor The amount of change in bearing angle (degrees) after the system sensor check screen is displayed (clockwise: "+", counterclockwise: "-").

*d: Reset
Display Content
Reset When this switch is pressed and held for 3 seconds or more, the values for display items of SPD signal and gyro sensor signal are reset and display "0".

*e: Gyro/Distance correction study situation
Display Content
Gyro/Distance correction study situation Displays learning status of Gyro/Distance correction

i.

When the "System Sensors Check" screen is displayed, check all the sensor signals.

HINT:

This screen is updated once per second.




e.
E235422E01
0.158,0.597 0.333,0.781 0.174,0.184 10 *a 0.356,0.695 0.631,0.695 false 0.158,0.872 0.333,1.056 0.174,0.184 10 *b 0.356,0.97 0.631,0.97 false 0.158,1.198 0.333,1.382 0.174,0.184 10 *c 0.356,1.297 0.631,1.297 false 3.089,1.202 3.263,1.386 0.174,0.184 10 *c 2.466,1.301 3.08,1.301 false 3.089,0.755 3.263,0.94 0.174,0.184 10 *d 2.672,0.854 3.08,0.854 false 3.087,1.529 3.261,1.713 0.174,0.184 10 *e 2.923,1.628 3.078,1.628 false 2.665,1.125 3.033,1.125 3.033,1.125 3.033,0.859 false

GPS Time Setting

Screen Description
Display Content
*a: Time display Displays the date and time in the device.
*b: Time setting screen Setting is possible only when GPS signals are not being received.
*c: Cursor movement switch Moves the cursor on the date and time setting screen to the right and left.
*d: Adjustment switch Adjusts values of items selected by the cursor.
*e: OK switch Selecting this switch after setting the date and time updates the date and time in the device (only when GPS signals are not received).

i.

When GPS signals are not being received, the data and time in the device can be adjusted.

HINT:

Time setting is possible only when GPS signals are not being received. When the navigation system is receiving GPS signals, priority is given to displaying the time and date received via GPS.





CHECK VEHICLE SIGNAL


HINT:
·

Vehicle signals received by the navigation receiver assembly are checked in the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E273700

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E280879

Select "Vehicle Signal" from the "Function Check/Setting I" screen.


d.
E285757

Vehicle Signal Check Mode

Screen Description
Display Content
Battery Battery voltage is displayed.
IG Ignition switch ON/OFF state is displayed.
PKB Parking brake ON/OFF state is displayed.
REV Reverse signal ON/OFF state is displayed.
SPEED Vehicle speed is displayed in km/h.
TAIL Tail signal (Light control switch) ON/OFF state is displayed.

HINT:
·

Only conditions have inputs are displayed.

·

This screen displays vehicle signals input to the navigation receiver assembly.



i.

When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.




CHECK HANDS-FREE VOICE QUALITY AND VOLUME SETTING


NOTICE:
·

Adjustment of the settings is required for each registered cellular phone.

·

If no cellular phone has been registered, all switches cannot be selected.



HINT:
·

The hands-free volume of a "Bluetooth" compatible phone can be adjusted using the following procedure.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.




b.
E273700

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E280880

Select "HF Voice Quality Setting" from the "Function Check/Setting I" screen.


d.
E273710E01
3.058,0.884 3.320,1.096 0.262,0.211 10 *a 3.064,1.4 3.326,1.611 0.262,0.211 10 *b 1.669,1.812 1.931,2.024 0.262,0.211 10 *c 2.88,0.976 3.029,0.976 false 2.857,1.48 3.029,1.48 false 1.786,1.554 1.786,1.829 false

Hands-Free Voice Quality Setting (Voice Quality Type adjustment)

Screen Description
*a Numeric keypad
*b Setting button
*c Reset button

i.

If necessary, refer to the table below to adjust the voice quality type with the numeric keypad.


ii.

When adjusting the settings, use the number pad on the screen to input the voice quality type according to the table.

Settings
Parameter Target Phenomenon Voice Quality Type Positive Effect of Changing Voice Quality Negative Effect of Changing Voice Quality
A
(Noise)
The other party hears background noise when listening to your voice. 1000 The amount of background noise the other party hears when listening to your voice is reduced. The volume of voice the other party hears when listening to your voice may temporarily drop.
B
(Noise)
The other party hears a lot of background noise when listening to your voice. 2000 The amount of background noise the other party hears when listening to your voice is sharply reduced. The volume of voice the other party hears when listening to your voice may temporarily drop.
C
(Echo)
The other party hears weak echoes. 0100 The amount of echo is reduced (low level). Sound quality of the other party deteriorates (low level).
D
(Echo)
The other party hears strong echoes. 0200 The amount of echo is reduced (high level). Sound quality of the other party deteriorates (high level).

Settings (When Multiple Phenomena Occurred)
Parameter Target Phenomenon Voice Quality Type Positive Effect of Changing Voice Quality Negative Effect of Changing Voice Quality
A+C The other party hears background noise and weak echoes when listening to your voice. 1100
·

The amount of background noise the other party hears when listening to your voice is reduced.

·

The amount of echo is reduced (low level).


·

The volume of voice may drop temporarily.

·

Sound quality of the other party deteriorates (low level).


A+D The other party hears background noise and strong echoes when listening to your voice. 1200
·

The amount of background noise the other party hears when listening to your voice is reduced.

·

The amount of echo is reduced (high level).


·

The volume of voice may drop temporarily.

·

Sound quality of the other party deteriorates (high level).


B+C The other party hears a lot of background noise and weak echoes when listening to your voice. 2100
·

The amount of background noise the other party hears when listening to your voice is sharply reduced.

·

The amount of echo is reduced (low level).


·

The volume of voice may drop temporarily.

·

Sound quality of the other party deteriorates (low level).


B+D The other party hears a lot of background noise and strong echoes when listening to your voice. 2200
·

The amount of background noise the other party hears when listening to your voice is sharply reduced.

·

The amount of echo is reduced (high level).


·

The volume of voice may drop temporarily.

·

Sound quality of the other party deteriorates (high level).



HINT:
·

The default value is "0000".

·

Settings will be applied when the setting button is selected.

·

If voice quality type values that are not in the table are input, the setting will not be applied and a positive effect may not be gained.

·

If the quality of phone calls decreases due to the changed settings, return the settings to "0000" by pressing the "INIT" switch.






CHECK SPEAKER


HINT:
·

This function is used when checking the speaker wiring and whether the speakers are functioning properly.

·

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.



a.

Turn audio mode on and play any audio source.

HINT:

This audio source will be used for the speaker check.




c.
E268484

Select "Failure Diagnosis" from the "Service Menu" screen.


d.
E276579

Select "System Check" from the "Failure Diagnosis" screen.


e.
E273721

Select "SP Check ON" from the "System Check Mode" screen.


f.

Check the speaker wiring and check that the speakers are functioning properly.

HINT:
·

Check that each speaker outputs sound from the selected audio source properly.

·

"SP Check OFF" is displayed during the speaker check.

·

Sound can be heard from the speakers around the vehicle in order beginning from the speaker on the front passenger side.

·

More than one speaker may sound simultaneously depending on the speaker wiring.




g.

Sound stops when any of the following conditions are met.

i.

The "SP Check OFF" switch is pressed.


ii.

Ignition switch off.


iii.

Diagnostic mode is turned off.


iv.

The screen is changed to another screen.


v.

Audio mode is turned off.




ENTUNE RESET PROCEDURE (w/ Entune Function)


a.

Duplicate the problem symptom.


b.

Check for DTCs and repair the systems for which any DTCs are output (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).


c.

Check cellular phone compatibility.

i.

Go to Toyota website and check if the cellular phone/vehicle is compatible.


ii.

If the cellular phone is not compatible, recommend to the customer a compatible cellular phone.



d.

Delete all paired devices from the cellular phone.

i.

The procedure varies based on phone model. Contact the service provider or cellular phone manufacturer if assistance is required.



e.

Remove the Entune app from the phone.

NOTICE:

Only perform this step if the customer is present and approves.


i.

The procedure varies based on phone model. Contact the service provider or cellular phone manufacturer if assistance is required.



f.

Reset the phone.

NOTICE:

Only perform this step if the customer is present and approves.


i.

Turn off the phone and remove the battery for 15 seconds. For instructions on how to reset cellular devices, refer to the appropriate manufacturer's website.



g.

Reinstall the Entune app on the phone. (If removed.)

i.

The procedure varies based on phone model. Contact the service provider or cellular phone manufacturer if assistance is required.



h.

Delete all personal data from the head unit.

i.

Record all radio station presets.


ii.

Delete all personal data from the head unit.

NOTICE:

Only perform this step if the customer is present and approves.


HINT:

Re-installation of applications must be completed before applications will appear on the head unit.




i.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


i.

Record all radio station presets.


ii.

Disconnect the cable from the negative (-) battery terminal and leave it disconnected for 2 minutes.



j.

Check if the problem symptom has been repaired.